Advantech PCE-7210 Bedienungsanleitung

PCE-7210

Dual Socket 604 Intel® Xeon® / LV Xeon®

Processor Card with PCI Express / IPMI /

VGA/ Dual Gigabit LAN / FSB 800MHz

User Manual

PCE-7210 User Manual ii

This document is copyrighted, 2006, by Advantech Co., Ltd. All rights

are reserved. Advantech Co., Ltd. reserves the right to make improve-

ments to the products described in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated or transmit-

ted in any form or by any means without the prior written permission of

Advantech Co., Ltd. Information provided in this manual is intended to

be accurate and reliable. However, Advantech Co., Ltd. assumes no

responsibility for its use, nor for any infringements upon the rights of

third parties which may result from its use.

Acknowledgements

• PICMG™ and the PICMG™ logos are trademarks of the PCI Industrial

Computers Manufacturers Group.

• All other product names or trademarks are properties of their respective

owners.

Certifications

• CE

• FCC Class A

Part No. 2002721000 1st Edition

Printed in Taiwan June, 2006

iii

A Message to the Customer

Advantech customer services

Each and every Advantech product is built to the most exacting specifica-

tions to ensure reliable performance in the harsh and

demanding conditions typical of industrial environments. Whether your

new Advantech equipment is destined for the laboratory or the factory

floor, you can be assured that your product will provide the reliability and

ease of operation for which the name Advantech has come to be known.

Your satisfaction is our primary concern. Here is a guide to

Advantech’s customer services. To ensure you get the full benefit of our

services, please follow the instructions below carefully.

Technical support

We want you to get the maximum performance from your products. So if

you run into technical difficulties, we are here to help. For the most fre-

quently asked questions, you can easily find answers in your product doc-

umentation. These answers are normally a lot more detailed than the ones

we can give over the phone.

So please consult this manual first. If you still cannot find the answer,

gather all the information or questions that apply to your problem, and

with the product close at hand, call your dealer. Our dealers are well

trained and ready to give you the support you need to get the most from

your Advantech products. In fact, most problems reported are minor and

are able to be easily solved over the phone.

In addition, free technical support is available from Advantech engineers

every business day. We are always ready to give advice on application

requirements or specific information on the installation and operation of

any of our products.

PCE-7210 User Manual iv

Product warranty

Advantech warrants to you, the original purchaser, that each of its prod-

ucts will be free from defects in materials and workmanship for two years

from the date of purchase.

This warranty does not apply to any products which have been repaired or

altered by persons other than repair personnel authorized by Advantech,

or which have been subject to misuse, abuse, accident or improper instal-

lation. Advantech assumes no liability under the terms of this warranty as

a consequence of such events.

If an Advantech product is defective, it will be repaired or replaced at no

charge during the warranty period. For out-of-warranty repairs, you will

be billed according to the cost of replacement materials, service time and

freight. Please consult your dealer for more details.

If you think you have a defective product, follow these steps:

1. Collect all the information about the problem encountered. (For

example, type of PC, CPU speed, Advantech products used, other

hardware and software used, etc.) Note anything abnormal and list

any on-screen messages you get when the problem occurs.

2. Call your dealer and describe the problem. Please have your man-

ual, product, and any helpful information readily available.

3. If your product is diagnosed as defective, obtain an RMA (return

material authorization) number from your dealer. This allows us to

process your return more quickly.

4. Carefully pack the defective product, a fully-completed Repair and

Replacement Order Card and a photocopy proof of purchase date

(such as your sales receipt) in a shippable container. A product

returned without proof of the purchase date is not eligible for war-

ranty service.

5. Write the RMA number visibly on the outside of the package and

ship it prepaid to your dealer.

Before you begin installing your single board computer, please make sure

that the following materials have been shipped:

If any of these items are missing or damaged, contact your distributor or

sales representative immediately.

We have carefully inspected the PCE-7210 mechanically and

electrically before shipment. It should be free of marks and scratches and

in perfect working order upon receipt.

As you unpack the PCE-7210, check it for signs of shipping damage. (For

example, damaged box, scratches, dents, etc.) If it is damaged or it fails to

meet the specifications, notify our service department or your local sales

representative immediately. Also notify the carrier. Retain the shipping

carton and packing material for inspection by the carrier. After inspec-

tion, we will make arrangements to repair or replace the unit.

PCE-7210 User Manual vi

Initial Inspection

Before you begin installing your single board computer, please make sure

that the following materials have been shipped:

If any of these items are missing or damaged, contact your distributor or

sales representative immediately.

We have carefully inspected the PCE-7210 mechanically and electrically

before shipment. It should be free of marks and scratches and in perfect

working order upon receipt.

As you unpack the PCE-7210, check it for signs of shipping damage. (For

example, damaged box, scratches, dents, etc.) If it is damaged or it fails to

meet the specifications, notify our service department or your local sales

representative immediately. Also notify the carrier. Retain the shipping

carton and packing material for inspection by the carrier. After inspec-

tion, we will make arrangements to repair or replace the unit.

1 PCE-7210 Dual Intel® Xeon® / LV Xeon® processor-based single

board computer

1 PCE-7210 Startup Manual

1 CD with driver utility and manual (in PDF format)

1 FDD cable P/N: 1700340640

2 Ultra ATA 66/100 HDD cables P/N: 1701400452

2 Serial ATA HDD data cable P/N: 1700071000

2 Serial ATA HDD power cable P/N: 1703150102

1 Printer (parallel) port & COM port cable kit P/N: 1701260305

1 Dual COM port cable kit P/N: 1701092300

1 Y cable for PS/2 keyboard and PS/2 mouse P/N: 1700060202

2 CPU cooler P/N: 1750000282

1 VGA cable P/N: 1700000259

1 Video Cable (S / Composite terminal) P/N: 1700000784

Warranty card

vii

Verified CPU List

Verified Memory List

Table 1.1: Verified CPU List

CPU Freq. Spec.

Core

Step-

ping

Thermal Vcore FSB Mfg.

Tech HT L2

cache

Pack-

age Type

XEON 3.6 G SL7ZC N0 110W 1.4V max 800 90nm Y 2MB NA 604 pin

XEON 3.2 G SL7ZE N0 110W 1.4V max 800 90nm Y 2MB NA 604 pin

XEON 3.0 G SL7ZF N0 110W 1.4V max 800 90nm Y 2MB NA 604 pin

XEON 2.8 G SL7ZG N0 110W 1.4V max 800 90nm Y 2MB NA 604 pin

XEON 3.6 G SL7PH E0 103W 1.4V max 800 90nm Y 1MB NA 604 pin

XEON 3.0 G SL7TC E0 103W 1.4V max 800 90nm Y 1MB NA 604 pin

Table 1.2: Verified Memory List

Brand Size Speed Type ECC Part Number Memory

Apacer

(RoHS)

512MB DDR2 400 Register

DDR2

Y 78.91G57.421 ELPIDA E5108AE-5C-E

(64x8)

1GB DDR2 400 Register

DDR2

Y 78.01G57.420 ELPIDA E5108AE-5C-E

(64x8)

Unigen

(RoHS)

1GB DDR2 400 Register

DDR2

Y UG12T7200L8DR-

5AC

ELPIDA E5108AG-5C-E

(64x8)

2GB DDR2 400 Register

DDR2

Y UG25T7200L4DR-

5AW

ELPIDA E5104AE-5C-E

(128x4)

Trancend

512MB DDR2 400 Register

DDR2

Y NA SEC K4T51043QC

2GB DDR2 400 Register

DDR2

Y NA SEC K4T51043QC

PCE-7210 User Manual viii

Certification and Safety Instructions

This device complies with the requirements in part 15 of the FCC rules: Operation is sub-

ject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may

cause undesired operation

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide rea-

sonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio fre-

quency energy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of this device in a

residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his/her own expense. The user is advised that any

equipment changes or modifications not expressly approved by the party responsible for

compliance would void the compliance to FCC regulations and therefore, the user's

authority to operate the equipment.

CAUTION!!

There is a danger of a new battery exploding if it is incorrectly installed. Do not

attempt to recharge, force open, or heat the battery. Replace the battery only with

the same or equivalent type recommended by the manufacturer. Discard used bat-

teries according to the manufacturer’s instructions.

Contents

Chapter 1 Hardware Configuration .................................2

1.1 Introduction ....................................................................... 2

1.2 Features ............................................................................. 4

1.3 Specifications .................................................................... 5

1.3.1 System............................................................................. 5

1.3.2 Memory........................................................................... 5

1.3.3 Input/Output.................................................................... 5

1.3.4 VGA interface................................................................. 6

1.3.5 Ethernet LAN.................................................................. 6

1.3.6 Industrial features ........................................................... 6

1.3.7 Mechanical and environmental specifications................ 6

1.4 Jumpers and Connectors.................................................... 7

Table 1.1:Jumper descriptions ........................................ 7

Table 1.2:Connector descriptions ................................... 7

1.5 Board Layout: Jumper and Connector Locations.............. 9

Figure 1.1:Jumper and Connector locations ................... 9

1.6 PCE-7210 Block Diagram.............................................. 10

Figure 1.2:Block Diagram ............................................ 10

1.7 Safety Precautions .......................................................... 11

1.8 Jumper Settings ............................................................... 12

1.8.1 How to set jumpers ....................................................... 12

1.8.2 CMOS clear (CMOS1) ................................................. 12

Table 1.3:CMOS (CMOS1).......................................... 12

1.8.3 Watchdog timer output (JWDT1) ................................. 13

Table 1.4:Watchdog timer output (JWDT1)................. 13

1.9 System Memory .............................................................. 14

Figure 1.3:PCE-7210 DIMM location .......................... 14

Table 1.5:Memory Configuration ................................. 15

1.10 Memory Installation Procedures ..................................... 15

1.11 Processor Installation ...................................................... 16

1.12 CPU Cooler Installation .................................................. 17

Figure 1.4:CPU Cooler Installation .............................. 17

Chapter 2 Connecting Peripherals .................................20

2.1 Introduction ..................................................................... 20

2.2 1st & 2nd IDE Connectors (IDE1, IDE2) ....................... 20

Figure 2.1: PCE-7210 IDE1 and IDE2 location ........... 20

2.3 Floppy Drive Connector (FDD1) .................................... 21

Figure 2.2: PCE-7210 FDD1 location .......................... 21

2.4 Parallel Port (LPT1) ........................................................ 22

PCE-7210 User Manual x

Figure 2.3: PCE-7210 LPT1 location ........................... 22

2.5 VGA Connector (VGA1) ................................................ 23

Figure 2.4:VGA Connector (VGA1) ............................ 23

2.6 VGA-2 Connector (VGA2)............................................. 23

Figure 2.5:VGA Connector (VGA2) ............................ 23

2.7 DVI connector (DVI1) .................................................... 24

Figure 2.6:DVI connector (DVI1) ................................ 24

2.8 Serial Ports (COM1, COM3, COM4) ............................. 25

Figure 2.7:Serial Ports (COM1, COM3, COM4) ......... 25

2.9 PS/2 Keyboard/Mouse Connector (KBMS1).................. 26

Figure 2.8:

PS/2 Keyboard/Mouse Connector (KBMS1)

..... 26

2.10 External Keyboard Connector (KBMS2)........................ 26

Figure 2.9: External Keyboard Connector (KBMS2)... 26

2.11 CPU Fan Connectors (CPUFAN1, CPUFAN2).............. 27

Figure 2.10:

CPU Fan Connectors (CPUFAN1, CPUFAN2)

2.12 Front Panel Connectors (JFP1, JFP2, JFP3) .................. 27

Figure 2.11:

Front Panel Connectors (JFP1, JFP2, JFP3)

.... 27

Figure 2.12:Detail (JFP1, JFP2, JFP3) ......................... 28

2.12.1 ATX soft power switch (JFP1 / PWR_SW) ................. 28

2.12.2 2.12.2 Reset (JFP1 / RESET)........................................ 28

2.12.3 HDD LED (JFP2 / HDDLED)...................................... 28

2.12.4 SM Bus Connector (JFP2 / SNMP) .............................. 28

2.12.5 External speaker (JFP2 / SPEAKER) ........................... 28

2.12.6 Power LED and keyboard lock connector (JFP3 /

PWR_LED&KEY LOCK) ........................................... 29

Table 2.1:ATX power supply LED status (No support for

AT power)..................................................... 29

2.13 HW Monitor Alarm (JOBS1).......................................... 30

Figure 2.13:HW Monitor Alarm (JOBS1).................... 30

Table 2.2:Hardware Monitor Alarm setting ................. 30

2.14 Dual Giga LAN RJ45 connector (LAN12) ..................... 31

Figure 2.14:Dual Giga LAN RJ45 connector (LAN12)31

2.15 AC'97 Link connector (AC97) ........................................ 31

Figure 2.15:AC'97 Link connector (AC97) .................. 31

2.16 Serial ATA interface (SATA1, SATA2)......................... 32

Figure 2.16:Serial ATA interface (SATA1, SATA2)... 32

2.17 LAN1 and LAN2 LED connector (LANLED1) ............. 32

Figure 2.17:

LAN1 and LAN2 LED connector (LANLED1)

2.18 BMC connector (BMC1)................................................. 33

Figure 2.18: BMC connector (BMC133

2.19 GPIO header (GPIO1)..................................................... 33

Figure 2.19:GPIO header (GPIO1)............................... 33

Inhaltsverzeichnis

Andere Advantech Hauptplatine Handbücher

Advantech

Advantech MIC-3385 Bedienungsanleitung

Advantech

Advantech AIMB-701 LGA1155 Installations- und Betriebshandbuch

Advantech

Advantech PCA-6751 Series Bedienungsanleitung

Advantech

Advantech ROM-DB3900 Bedienungsanleitung

Advantech

Advantech ASMB-786 Bedienungsanleitung

Advantech

Advantech PCE-5128 Bedienungsanleitung

Advantech

Advantech ASMB-782 Installations- und Betriebshandbuch

Advantech

Advantech PCM-9365 Installations- und Betriebshandbuch

Advantech

Advantech SOM-AB5810 Bedienungsanleitung

Advantech

Advantech PCM-9576F Bedienungsanleitung

Advantech

Advantech PCM-4862 Installations- und Betriebshandbuch

Advantech

Advantech AIMB-584 Bedienungsanleitung

Advantech

Advantech PCM-9380 Installations- und Betriebshandbuch

Advantech

Advantech AIMB-216 Bedienungsanleitung

Advantech

Advantech PCM-3341 Series Bedienungsanleitung

Advantech

Advantech MIO-3360 Bedienungsanleitung

Advantech

Advantech SIMB-A01 Bedienungsanleitung

Advantech

Advantech MIC-3355 Bedienungsanleitung

Advantech

Advantech PCM-4825 Bedienungsanleitung

Advantech

Advantech PCM-9374 Installations- und Betriebshandbuch

Advantech

Advantech AIMB-586 Bedienungsanleitung

Advantech

Advantech AIMB-213 Installations- und Betriebshandbuch

Advantech

Advantech PCA-6013 Bedienungsanleitung

Advantech

Advantech SOM-4475 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung