AEG Ergorapido 2in1 Bedienungsanleitung

16 9

Front Back

3Content

English

Thank you for choosing an AEG Ergorapido vacuum

cleaner. Ergorapido is a rechargeable handheld

stick vacuum cleaner intended for use on light dry

household debris. In order to ensure the best results,

always use original AEG accessories. They have been

designed especially for your vacuum cleaner.

Table of contents

Unpacking and assembly ......................4

Charging ...................................5

Vacuuming..................................6

Emptying and cleaning ........................7

Cleaning brush roll, hose and wheels .............8

Removing the batteries .......................10

Safety precaution ...........................11

Consumer information........................11

Features/Accessories

1 On/off button

2 On/off button, hand unit

3 Handle

4 Locking screw

5 Release button, hand unit

6 Charging station, wall unit

7 Charging station, ﬂoor unit

8 Adaptor

9 Fine ﬁlter (inner ﬁlter)

10 Pre ﬁlter (outer ﬁlter)

11 Release button, dust container

12 Battery display, Lithium version*

13 Dust container

14 Vacuum cleaner lid

15 Brush

16 Crevice nozzle

17 Brush roll release button*

18 Hatch cover for brush roll*

19 Brush roll

20 BRUSHROLLCLEAN™ TECHNOLOGY button*

21 Nozzle front lights

22 Charging indicator, NiMH version*

23 Parking strip

* Certain models only

Unpacking and assembly

Charging station

1. Check that all parts are in the box. Fit the handle

by carefully inserting it into the lower main body.

Make sure that the cable does not jam.

2. Secure the handle by tightening the locking screw

supplied. Use a screwdriver or a coin.

1. Position the charging station well away from

heat sources, direct sunlight or wet places. Insert

the adaptor into the mains and connect it to the

charging station.

2. On the bottom of the charging station there is a

hollow space where unused cable can be wound.

3. The wall unit can also be mounted on a wall.

Separate it from the ﬂoor unit. Always ensure that

the wall can withstand the weight of Ergorapido.

Unpacking and assembly

1. 3 blue lights: battery capacity >75%

2 blue lights: battery capacity 75-25%

1 blue light: battery capacity <25%

1 blue blinking light: battery capacity – empty

2. If a red light is lit: Unit is too hot. Clean ﬁlters,

brush roll, hose and put on charge.

3. If a red light is blinking: Motor is overloaded.

Clean brush roll.

4. When fully charged the LED’s* will turn off

and go into standby mode = much lower power

consumption, indicated with one blink per minute.

5. The red and blue light are blinking: please refer

to page 9.

1. Ergorapido: The indicator light will come on

once the Ergorapido is positioned correctly in the

charging station. When fully charged, the LED will

be on for a few seconds per minute.

2. Ergorapido Plus: The battery capacity display

lights will come on one after another as the

machine is charging after being positioned

correctly in the charging station.

3. When fully discharged, approximately 16 hours’

charging is required to regain full battery capacity

(4 hours for Ergorapido Plus). Leave Ergorapido

on charge when not used to maintain battery

performance.

Charging

Battery capacity display*

*Ergorapido Plus

3. Adjust the power level by pushing the lower part of

the on/off button:

2. Start Ergorapido by pushing the on/off button.

3. Start/stop the hand unit by pushing the start

button.

1. You should regularly check that the nozzle

wheels and the brush roll are clean in order to

avoid scratching sensitive ﬂoors.

1. Remove the hand unit by pressing the release

buttons. The crevice nozzle and small brush are

stored in the charging station.

2. Attach the crevice nozzle to facilitate cleaning

of areas difﬁcult to reach, or attach the brush for

dusting.

Vacuuming floors and carpets

Vacuuming furniture, car seats etc.

Vacuuming

Ergorapido’s dust container must be emptied

regularly and the dust container and the ﬁlters need

to be cleaned to maintain a high suction power.

Never wash dust containers or ﬁlters in a dishwasher.

1. Quick emptying of the dust container. Open the

vacuum cleaner lid. Clean the dust container by

placing the hose of another vacuum cleaner at the

opening.

2. Emptying of the dust container. Remove the

ﬁlters, empty the contents into a dustbin. Return

ﬁlters and click dust container back into place.

3. Quick cleaning of the ﬁne ﬁlter. (Recommended

every cleaning). Release the dust container, pull/

release spring 5-6 times to dislodge dust.

4a.Cleaning of dust container and ﬁlters.

(Recommended every 5th cleaning). Release dust

container, take out both ﬁlters by pressing release

buttons.

4b.Separate both ﬁlters. Dust container and ﬁlters

can be shaken clean or rinsed in warm water

(never in dishwasher). All parts must be dry before

reassembled in reverse order.

Emptying and cleaning

The brush roll, the hose and the wheels may need to

be cleaned if they become blocked or jammed for any

reason.

Some Ergorapido models are equipped with

BRUSHROLLCLEAN™ TECHNOLOGY – a brush

cleaning function that helps to keep a clean brush

easily.

Please note that the BRUSHROLLCLEAN™

TECHNOLOGY function might not be able to remove

thick threads, wires or thick carpet ﬁbres caught in the

brush roll.

It is recommended to use this function once a week.

For best results use the BRUSHROLLCLEAN™

TECHNOLOGY function when the Ergorapido is fully

charged. 1. Make sure the cleaner is switched on and

stands on hard even surface. Do not use the

BRUSHROLLCLEAN™ TECHNOLOGY function on

deep carpets or long haired rugs.

2. Press the BRUSHROLLCLEAN™ TECHNOLOGY

button with your foot while the cleaner is switched

on. Hold for ca. 5 seconds or until all dirt and hair

is removed. Release the button.

There will be a cutting noise during this process,

this is normal

Cleaning the brush roll with the BRUSHROLLCLEAN™ TECHNOLOGY function*

Cleaning

* Certain models only

When the button is released, the brush is rotating and the nozzle front lights are on again. You can continue to use the Ergorapido for vacuuming as usual. The

BRUSHROLLCLEAN™ TECHNOLOGY function will remain disabled. To reset, the Ergorapido must be charged continuously for at least 10 minutes in the charging stand.

1. Ergorapido plus:

If - while holding the BRUSHROLLCLEAN™

TECHNOLOGY button pressed down – the brush

stops rotating, the nozzle front lights switch off

and the battery indicator light blinks red and blue,

release the BRUSHROLLCLEAN™ TECHNOLOGY

button.

2. Ergorapido:

If - while holding the BRUSHROLLCLEAN™

TECHNOLOGY button pressed down – the brush

stops rotating and the nozzle front lights switch off,

release the BRUSHROLLCLEAN™ TECHNOLOGY

button.

The BRUSHROLLCLEAN™ TECHNOLOGY function

is equipped with an overheating protection. It will

deactivate the brush roll if the BRUSHROLLCLEAN™

TECHNOLOGY function has been activated for more

than 30 sec (constant or interrupted) within one

discharging period.

1. First turn Ergorapido off. Push the brush roll

release button. The hatch cover will come slightly

free and the brush roll can be removed.

1. Loosen the catch and pull the hose from the

attachment. Remove any debris. Put the hose

back, lock using the catch.

2. If the wheels needs to be cleaned, remove them

carefully by using a small screwdriver.

3. Remove objects that may have become

jammed in the wheel shafts. Reassemble the

wheels by pressing them back into their tracks.

2. Lift out the brush roll and clean it. Use a sharp

object to remove threads. Reassemble the roll,

making sure it can spin freely. Close hatch cover.

Cleaning the brush roll

Cleaning the hose and wheels

To remove thicker threads or wires as well

as on models that are not equipped with the

BRUSHROLLCLEAN™ TECHNOLOGY, the brush

should be cleaned according to the following

instructions.

Cleaning 9

1. Batteries should always be run ﬂat before

removed. Ergorapido must be disconnected

from the charging station when removing the

batteries. Undo the screws. Carefully lift the hood.

2. Cut the connecting cables, remove the batteries,

put tape over the visible metal areas. Place

batteries in suitable packaging.

Improper handling of the batteries may be

hazardous. Return the complete handheld unit to a

recycling station. Batteries must be removed from

the appliance before it is scrapped or recycled.

Never dispose used batteries with household waste.

Removing batteries

Removing the batteries

Andere Handbücher für ergorapido 2in1

Inhaltsverzeichnis

Andere AEG Staubsauger Handbücher

AEG

AEG BHSS18 Bedienungsanleitung

AEG

AEG X Precision VX9 Bedienungsanleitung

AEG

AEG Electrolux minion ATI 7650 Bedienungsanleitung

AEG

AEG VAMPYR 831i electronic Bedienungsanleitung

AEG

AEG Liliput Bedienungsanleitung

AEG

AEG Rapido AG5104WDB Bedienungsanleitung

AEG

AEG X POWER VX7 Bedienungsanleitung

AEG

AEG VX4 Bedienungsanleitung

AEG

AEG Vampyr TC Electronic Series Bedienungsanleitung

AEG

AEG LX8 Bedienungsanleitung

AEG

AEG CX7 Li-21 Bedienungsanleitung

AEG

AEG AP 2-200 ELCP Bedienungsanleitung

AEG

AEG Liliout Bedienungsanleitung

AEG

AEG RSE 1400 Bedienungsanleitung

AEG

AEG UltraFlex Bedienungsanleitung

AEG

AEG VAMPYR 831i electronic Bedienungsanleitung

AEG

AEG Vampyr 5 Compact Series Bedienungsanleitung

AEG

AEG UltraCaptic Bedienungsanleitung

AEG

AEG LX9 X PRECISION Bedienungsanleitung

AEG

AEG CLEAN 6000 Bedienungsanleitung

AEG

AEG LX7 Power Bedienungsanleitung

AEG

AEG Green UltraOne oko Bedienungsanleitung

AEG

AEG VAMPYR CE Series Bedienungsanleitung

AEG

AEG Precision Brushroll Clean Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch

AEG ergorapido 2in1 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken