AEG Vampyr 6000 Kurzanleitung

SERVICE MANUAL

Muggenhofer Straße 135

D-904 9 Nürnberg

Germany

Fax +49 (0)911 3 3 14 0

TSE - N

Publ.-Nr.:

599 50 77 62

685

05.00

VACUUM CLEANERS

Edition:

Vacuum cleaners

Vampyr 6000

Vampyr 7000

Vampyr 8000

Repair notes

- 2 -

TSE-N 05.00 A. B. 599 50 77 62 EN

- 3 -

TSE-N 05.00 A. B. 599 50 77 62 EN

Disassembly and Assembly of Separate Components

Lid 16 Guided on both sides with hinge and lid necks. When removing,

raise the lid and press the flaps with the lid necks outward.

When closing the lid, the paper filter must be put in, raise the lid in

upright position and insert the hinge and lid necks in both sides.

Lock Key 13 Press key to the front using a screwdriver between lid 16 and key.

Locking Piece 15 Take out the spring wire, press the 2 clips of the lid 16 upward one

after the other using a small screwdriver while moving that piece

forward.

Accessory Tray 17 Guided with 2 necks (axes) on both sides.

Accessory Lid 1Press the lid in the middle of its front side down with your fingers,

the lid leaps up, press the 2 guiding necks inward and pull the lid

up.

During assembly first put the spring onto the axis, then put the lid

in open position to the necks, press downward and let it lock in; if

necessary, place the spring into the guide groove.

Accessory Lid Lock 14 Put a small screwdriver into the support, unlock it and press it

down.

During assembly put the guide bolt into the support and press it

from below to top into the device.

Paper Filter Safety

Device 22 Apply the screwdriver inside and press outward.

Switch Key,

Stop Key 18 The keys are snapped twice each.

It is better to raise and/or remove the lid completely when

performing these activities.

During disassembly press the key and put the screwdriver between

the key and potentiometer panel, slider panel respectively control

panel or key 4 (250 W, 110 W), apply to the snap-in catches and

press outward (possibly by turning), put the screwdriver between

the key and printed panel 2 (inclined ribs and press outward

(possibly by turning).

During assembly unlock the printed panel 2 respectively remove it

completely. Guide both outside snap-in catches of the key into the

pockets inside the rim of the support part 8 and press the key at

the inside down (possibly with a slight beat of your ball of the

thumb), so that the snap-in catch will be locked inside the

potentiometer panel 3, slider panel 20 respectively control panel or

key 4. Locking in respectively putting on the printed panel 2 leads

to the second lock of the key.

Printed Panel 2Unlock the snap-in catches, which are each snapped in twice on

the left and right side, one after the other, using a screwdriver.

Potentiometer Panel,

Slider Panel and Blind

Panel

20 Only mounted on, can be taken off.

3 – Keys 4Can be taken off and mounted on again; by mounting on the

printed panel 2 the keys are locked

- 4 -

TSE-N 05.00 A. B. 599 50 77 62 EN

Control Panel ?,

Rocker Switch 5

6Unlock the control panel, take off the rocker switch, put in the

rocker switch again with mounted-on adjusting spring and lock in

the control panel with the compression spring.

Rotary Electronic 27 Put in the rotary potentiometer into the device in support part 8.

Sliding Electronic 21 Insert the gear wheel symmetrically into the sliding part with the

slide potentiometer and apply it in the centre of rack and guide bar

move the complete unit to the right to the end of the rack and put

on the slider panel 20 with slider 19 the end stop at the right side;

in doing so, check the function whether the slide potentiometer is

guided by slider 19.

Slider 19 Lever the slider using a screwdriver between slider and panel.

During assembly put in the angle spring into the neck of the slider

and lock in the slider using a screwdriver.

Brake Lever 23 Expand the support (2 legs) using circlip pliers.

Lower Housing 24 Unscrew the 7 screws (1 of them below the microfilter box 12).

Microfilter Key 12 Press from outside to inside and unlock.

Wheel 26 Has to be unlocked with a screwdriver or pliers, if necessary lever

with a screwdriver between lower housing 24 and wheel.

Front Wheel 25 Lever with a screwdriver between lower housing 24 and wheel,

additionally unlock the neck in the middle with pliers or another

screwdriver.

Plug Box 9Press up the snap-in catch in the cable roller box and move a bit

outward, now press the plug box together from the outside and

unhinge the hang-in catches above and below.

Plug Funnel 10 Push out of the guide (cable roller side) upward. During assembly

the plug funnel must be pushed in first outside the support part 8

slightly inclined, so that both flaps reach the guide left and right at

the cable roller side; in doing so, the stopper must be adjacent

below outside the support part 8. Then push in the plug box 9 from

the outside passing the rims left and right of the plug funnel.

Fan 11 Remove both rubber buffers with pliers.

Electronic 7Unlock the 3 catches and pull them through downward; in doing so,

take out the indications in the printed panel 2 because of the wire

lengths.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AEG Staubsauger Handbücher

AEG

AEG UltraFlex Bedienungsanleitung

AEG

AEG VAMPYR Multi Bedienungsanleitung

AEG

AEG Precision Brushroll Clean Bedienungsanleitung

AEG

AEG ergospace Bedienungsanleitung

AEG

AEG Li-50 (21 Bedienungsanleitung

AEG

AEG RSE 1400 Bedienungsanleitung

AEG

AEG LX8 Bedienungsanleitung

AEG

AEG AP 2-200 ELCP Bedienungsanleitung

AEG

AEG VX9-4-8IBX Bedienungsanleitung

AEG

AEG WX7 Series Bedienungsanleitung

AEG

AEG Ergorapido Bedienungsanleitung

AEG

AEG erhorapido 10,8V Bedienungsanleitung

AEG

AEG ergorapido 2in1 Bedienungsanleitung

AEG

AEG AP218E2-0 Bedienungsanleitung

AEG

AEG ultrasilencer Bedienungsanleitung

AEG

AEG LX5-2-2SW Bedienungsanleitung

AEG

AEG Electrolux smart 450 Bedienungsanleitung

AEG

AEG X CONVENIENCE HX6 Series Bedienungsanleitung

AEG

AEG X CONVENIENCE HX6 Series Bedienungsanleitung

AEG

AEG VAMPYR 831i electronic Bedienungsanleitung

AEG

AEG BHSS18C Bedienungsanleitung

AEG

AEG X SILENCE VX8 Bedienungsanleitung

AEG

AEG X PERFORMANCE RX7 Bedienungsanleitung

AEG

AEG VAMPYRETTE 315 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung