Agilent Technologies 34136A Bedienungsanleitung

User’s Guide

Agilent Technologies 34136A High Voltage Probe

WARNING This high voltage probe is designed to prevent accidental shock to the operator when properly used.

This operating note must be read and understood prior to using the probe. Improper procedures or

incorrect analysis of the measurement situation can result in serious shock.

General Information

The Agilent Technologies 34136A High Voltage Probe is an accessory to be used with analog or digital

multimeters having an input resistance of 10 M Ω ( ±1 %) . The Agilent Technologies 34136A is a

1000:1 divider which extends a voltmeter’s measurement capability to 40 kV dc/ 28 kV rms ac.

Specifications

Other Characteristics

AC output derates with frequency to

-3db at 300 Hz. The graph at the right

shows typical AC accuracy.

Actual AC accuracy varies with the

amount of shunted input capacitance.

Maximum Input Voltage Temperature Coefficient

DC Voltage: 40kV

AC Voltage: (0 to 300 Hz) 28 kV

RMS

Less than 200ppm/ °C

Accuracy Division Ratio Accuracy

DC volts: ±2 % ( 1 kV to 20 kV)

±3 % ( 2 0 kV to 40 kV)

1000:1 ±1% when terminated in 10 MΩ

2000:1 ±6 % when terminated in 1 MΩ

Note: For the 34401A, 34405A, L4411A, 34410A/11A,

and 3458A multimeters, the ACV input impedance function

has a 1 MΩinput impedance.

Pollution Degree 2

Input Resistance Operating Temperature

1000 MΩ0°C to +50 ° C

Cable Length: Storage Temperature:

1 meter −20 ° C to +70 °C

Altitude: Humidity

Up to 4,600 meters (15,000 ft) Up to 80% relative humidity at +40

°C

Accuracy

AC Volts: 5% at 60 Hz

-3

Atten

(dB)

Frequency

DC 300 Hz

Safety Precautions

• This high voltage probe must only be used by personnel who are trained, experienced, or otherwise

qualified to recognize hazardous situations and who are trained in the safety precautions that are

necessary to avoid possible injury when using such a device.

• Do not work alone when working with high voltage circuits

• For your own safety, inspect the probes for cracks and frayed or broken leads before each use.

If defects are noted, DO NOT use the probe.

• Hands, shoes, floor and work bench must be dry. Avoid making measurements under humid,

damp or other environmental conditions that might effect the safety of the measurement situation.

• It is advisable to turn the high voltage source off before connecting or disconnecting the probe.

• The probe body should be kept clean and free of any conductive contamination. Refer to the section

on cleaning.

Operation

• Connect the plugs to the volts [Hi] and com [Lo] terminals of your voltmeter

• Select the desired voltage function and range; do not use autoranging

• Whenever possible, turn the high voltage source off before making any connections

• Connect the divider probe common lead (alligator clip) to a good earth ground or reliable chassis

ground

Warning • Do not attempt to take measurements from sources where the chassis or return lead is not grounded

• The ground lead is critical to the safe operation of the probe. Failure to make this connection when

making high voltage measurements may result in personal injury or damage to the probe or voltmeter.

This connection must always be made BEFORE the probe tip comes in contact with the high voltage

and must not be removed until the probe tip has been removed from the high voltage source.

• Do not connect the ground clip lead to the high voltage source for any reason.

• Before turning the high voltage on, make sure that no part of your body is in contact with the device

under test.

• Measure the voltage remembering that the voltage being measured is 1000 times greater than the

voltmeter reading.

• Turn the high voltage off.

• Disconnect the probe tip from the high voltage source BEFORE removing the ground clip lead.

Cleaning

• Clean only the exterior probe body and cables. Use a soft cotton cloth lightly moistened with a mild

solution of detergent and water. Do not allow any portion of the probe to be submerged at any time.

• Dry the probe thoroughly before attempting to make voltage measurements.

• Do not subject the probe to solvents or solvent fumes as these can cause deterioration of the probe

body and cables.

Manual Part Number

34136-92000

*34136-92000*

Edition 2, September 2011

Andere Agilent Technologies Messgerät Handbücher

Agilent Technologies

Agilent Technologies 8702D Bedienungsanleitung

Agilent Technologies

Agilent Technologies 4352B Bedienungsanleitung

Agilent Technologies

Agilent Technologies N9010A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 16517A Service-Handbuch

Agilent Technologies

Agilent Technologies E8361C Kurzanleitung

Agilent Technologies

Agilent Technologies WireScope 350 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 71612 Bedienungsanleitung

Agilent Technologies

Agilent Technologies Agilent 4396B Bedienungsanleitung

Agilent Technologies

Agilent Technologies u8903a Bedienungsanleitung

Agilent Technologies

Agilent Technologies E8362 Bedienungsanleitung

Agilent Technologies

Agilent Technologies Cary 60 Bedienungsanleitung

Agilent Technologies

Agilent Technologies HP 5890 II Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies E8364BPNA Series Kurzanleitung

Agilent Technologies

Agilent Technologies 490 Micro GC Bedienungsanleitung

Agilent Technologies

Agilent Technologies HP E5574A Bedienungsanleitung

Agilent Technologies

Agilent Technologies E5071C ENA Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 4285A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 4285A Bedienungsanleitung

Agilent Technologies

Agilent Technologies E4404B Kurzanleitung

Agilent Technologies

Agilent Technologies 85051B Handbuch

Agilent Technologies

Agilent Technologies PNA Series Betriebsanleitung

Agilent Technologies

Agilent Technologies 4263B Bedienungsanleitung

Agilent Technologies

Agilent Technologies U5303A Benutzerhandbuch

Agilent Technologies

Agilent Technologies 8753ES Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung