Agilent Technologies B2901 Bedienungsanleitung

Agilent B2901/02/11/12A Precision Source/Measure Unit

How to source continuous pulses without any measurement

This material shows how to setup the instrument to source continuous pulses without any measurement using the

B2901/02/11/12A, through example to source 2 V continuous pulses with the timing parameters such as 300 us pulse

delay, 200 us pulse width and 500 us source trigger period.

Figure 1 shows the timing chart for the continuous pulse source.

Figure 1. Timing chart for the continuous pulse source

It is required to abort the instrument when you’d like to stop sourcing continuous pulses.

This material also shows how to abort the instrument to stop continuous pulses.

Setting up the pulse condition

Step 1. Press to edit the source function, and then select to set the source function to the voltage

source.

TIMER TriggerOutput ON

Source Value

Output

Off State

V or I

Time

TPD TPW

Pulse

Peak Value

TPD TPW TPD TPW

TSP TSP TSP

TPW : Pulse WidthTPD : Pulse Delay TSP : Source Trigger Period

(1) Press Mode (2) Press VOLTS (V)

Agilent B2901/02/11/12A Precision Source/Measure Unit

Step 2. Press to edit the source value, and then enter 0 V to set the source value to 0 V.

Step 3. Press to edit the limit value, and then enter 10 mA to set the limit value to 10 mA.

Step 4. Press to change the keys shown in Assist keys, and then press to show Pulse Sub-Panel.

Step 5. Press , then press to set the pulse source ON. After turning on the pulse source, you can

see Source Shape which shows the pulse source mode.

(1) Press Source (2) Enter Source Value

(1) Press Limit (2) Enter Limit Value

(1) Press Show Pulse (2) Pulse Sub-Panel appears

(1) Press ON Source Shape

Agilent B2901/02/11/12A Precision Source/Measure Unit

Step 6. Rotate to select Channel 1 Pulse Parameters and set them up as below.

(Peak: 2 V, Delay: 300 us, Width: 200 us)

Step 7. Press to show Trigger Sub-Panel.

Step 8. Press to edit the trigger type, and then select to set the trigger type to MANUAL.

(1) Press Show Trigger (2) Trigger Sub-Panel appears

(2) Press MANUAL(1) Press

Agilent B2901/02/11/12A Precision Source/Measure Unit

Step 9. Rotate to select the source trigger period and press to edit it. Then enter 500 us to set the

source trigger period to 500 us.

Step 10. Rotate to select the source trigger source and press to edit it. Then press to set

the source trigger source to TIMER.

Step 11. If you aren’t on the top of the Function menu, press repeatedly to return to the top level.

Step 12. Press and then press to open Trigger Configuration dialogue.

(2) Enter Source Trigger Period(1) Rotate and press

Source Trigger Period

to edit

(2) Press TIMER(1) Rotate and press

Source Trigger Source

to edit

On the top level of the Function menu

In the middle level of the Function menu

Any tree structure can’t be seen

Some tree structure can be seen

(1) Press Trigger

(2) Press Config

Agilent B2901/02/11/12A Precision Source/Measure Unit

Step 13. Press and select to specify the layer, the trigger parameters of which are configured.

Step 14. Rotate to select the arm count and press to edit it. Then press to set the arm

count to INFINITY.

Step 15. Press to make the modification effective.

(2) Press ARM(1) Press

(2) Press INF.

(1) Rotate and press

ARM Count

to edit

(1) Press OK to make the modification effective

Agilent B2901/02/11/12A Precision Source/Measure Unit

Starting sourcing the continuous pulses

Step 16. If you aren’t on the top of the Function menu, press repeatedly to return to the top level.

Step 17. Press , , , and then press to start sourcing the

continuous pulses.

On the top level of the Function menu

In the middle level of the Function menu

Any tree structure can’t be seen

Some tree structure can be seen

(1) Press Trigger

(2) Press Initiate

(3) Press Trans.

(4) Press Ch 1

Agilent B2901/02/11/12A Precision Source/Measure Unit

Stopping sourcing the continuous pulses

Step 18. If you aren’t on the top of the Function menu, press repeatedly to return to the top level.

Step 19. Press , , , and then press to stop sourcing the

continuous pulses.

On the top level of the Function menu

In the middle level of the Function menu

Any tree structure can’t be seen

Some tree structure can be seen

(1) Press Trigger

(2) Press Abort

(3) Press Trans.

(4) Press Ch 1

Andere Handbücher für B2901

Dieses Handbuch passt für folgende Modelle

Andere Agilent Technologies Messgerät Handbücher

Agilent Technologies

Agilent Technologies 3588A Bedienungsanleitung

Agilent Technologies

Agilent Technologies Agilent 86120B Bedienungsanleitung

Agilent Technologies

Agilent Technologies E8362C Installations- und Betriebshandbuch

Agilent Technologies

Agilent Technologies 16901A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 2200 TapeStation Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8719ET Handbuch

Agilent Technologies

Agilent Technologies InfiniiVision 7000B Series Bedienerhandbuch

Agilent Technologies

Agilent Technologies PSA Series Installations- und Betriebshandbuch

Agilent Technologies

Agilent Technologies X Series Benutzerhandbuch

Agilent Technologies

Agilent Technologies U1701B Handbuch

Agilent Technologies

Agilent Technologies G7035A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 490 Micro GC Bedienungs- und Wartungsanleitung

Agilent Technologies

Agilent Technologies Agilent 4396B Bedienungsanleitung

Agilent Technologies

Agilent Technologies E4980A Bedienungsanleitung

Agilent Technologies

Agilent Technologies E5071C Bedienungsanleitung

Agilent Technologies

Agilent Technologies PNA Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies FieldFox N9923A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6800 Series Kurzanleitung

Agilent Technologies

Agilent Technologies 4284A Installationsanleitung

Agilent Technologies

Agilent Technologies E5071C ENA Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies N6705 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8711C Bedienungsanleitung

Agilent Technologies

Agilent Technologies 89410A Handbuch

Agilent Technologies

Agilent Technologies Cary 100 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung