Agilent Technologies CrossLab CS Bedienungsanleitung

Agilent CrossLab CS

ADM Flow Meter

Operation Manual

Notices

No part of this manual may be reproduced

in any form or by any means (including

electronic storage and retrieval or

translation into a foreign language) without

prior agreement and written consent from

Agilent Technologies, Inc. as governed by

United States and international

Manual Part Number

G6691-90000

Edition

Third edition, December 2021

Printed in USA

Agilent Technologies, Inc.

2850 Centerville Road

Wilmington, DE 19808-1610 USA

Warranty

The material contained in this document is

provided “as is,” and is subject to being

changed, without notice, in future editions.

Further, to the maximum extent permitted

by applicable law, Agilent disclaims all

warranties, either express or implied, with

regard to this manual and any information

contained herein, including but not limited to

the implied warranties of merchantability

and fitness for a particular purpose. Agilent

shall not be liable for errors or for incidental

or consequential damages in connection

with the furnishing, use, or performance of

this document or of any information

contained herein. Should Agilent and the

user have a separate written agreement

with warranty terms covering the material in

this document that conflict with these

terms, the warranty terms in the separate

agreement shall control.

Safety Notices

CAUTION

A CAUTION notice denotes a

hazard. It calls attention to an

operating procedure, practice, or the

like that, if not correctly performed or

adhered to, could result in damage to

the product or loss of important

data. Do not proceed beyond a

CAUTION notice until the indicated

conditions are fully understood

and met.

WARNING

A WARNING notice denotes a

hazard. It calls attention to an

operating procedure, practice, or the

like that, if not correctly performed or

adhered to, could result in personal

injury or death. Do not proceed

beyond a WARNING notice until the

indicated conditions are fully

understood and met.

Agilent CrossLab CS ADM Flow Meter Operation Manual 3

ADM Flow Meter

Introduction 5

Power/Mode button 5

Enter/Clear/Toggle button 6

Switching the ADM flow meter On and Off 7

Notes, Cautions, and Warnings 8

Principles of Operation 10

Product Specifications 11

Display 12

Operating Modes 13

Volumetric flow mode 13

Mass flow mode 13

Split mode 14

Info mode 14

Making a Flow Measurement 20

Storing Flow Measurements 21

Reading and Setting a Split Ratio 23

About Flow Measurements 25

USB Interface 26

Warning and Error Indications 28

Warning indication 28

Error indication 28

Low battery indication 29

Power Indications 30

Installing and Replacing the Cartridge 31

Installing the cartridge 31

Swapping or replacing the cartridge with ADM

ADM Flow Meter

4 Agilent CrossLab CS ADM Flow Meter Operation Manual

flow meter cartridge 31

Replacing the Batteries 33

Upgrading the Firmware/Retrieving

Certificate of Calibration 35

Using the Flow Meter Stand 36

A Note About Backpressure 37

Technical Support 37

Other Features 37

Safety and Regulatory Certification 38

Class A EMC certification 38

ADM Flow Meter

Introduction

Agilent CrossLab CS ADM Flow Meter Operation Manual 5

Introduction

The Agilent ADM flow meter is controlled with two buttons on

the front of the instrument directly below the screen, as shown

in Figure 1. The functions of these buttons are described in

this section.

Power/Mode button

The Power/Mode button is used to switch the flow meter on

and off, as well as to scroll through and select different

operational modes.

•To turn on the instrument, briefly press and release the

Power/Mode button.

•To turn off the instrument, press and hold the Power/Mode

button for three seconds.

•To scroll through the available modes, when the

instrument is on, briefly press and release the

Power/Mode button.

Figure 1. The Agilent CrossLab CS ADM flow meter front

screen buttons.

ADM Flow Meter

Enter/Clear/Toggle button

6 Agilent CrossLab CS ADM Flow Meter Operation Manual

Enter/Clear/Toggle button

The Enter/Clear/Toggle button is used to access additional

functionality within the operating modes.

•To store flow measurements in Volume mode and Mass

mode, briefly press and release Enter/Clear/toggle button.

•To set a reference value in Split mode, briefly press and

release Enter/Clear/Toggle button.

•To change the settings in Info mode, press and hold the

Enter/Clear/Toggle button for two seconds.

ADM Flow Meter

Switching the ADM flow meter On and Off

Agilent CrossLab CS ADM Flow Meter Operation Manual 7

Switching the ADM flow meter On

and Off

With the flow meter powered off, briefly press and release

Power/Mode button to turn the unit on. The screen will flash the

words ADM Flow Meter for approximately three seconds, then

begin operating.

With the unit powered on, press and hold the Power/Mode

button for three seconds to power down the unit.

Figure 2. The initial screen display for the Agilent ADM flow meter.

Figure 3. The shutdown screen for the Agilent ADM flow meter.

ADM Flow Meter

Notes, Cautions, and Warnings

8 Agilent CrossLab CS ADM Flow Meter Operation Manual

Notes, Cautions, and Warnings

NOTE

•The ADM flow meter cartridge is a calibrated device.

•Using the USB port to supply power does not recharge the

installed batteries.

•The ADM flow meter can also be powered by

rechargeable batteries, but the battery indicator may not

display correctly.

CAUTION

• Do not use the ADM flow meter in temperatures outside

of its specified operating range.

• The ADM flow meter should not be misused for

other purposes.

• The measurement calibration can be affected if the

instrument is exposed to temperatures above 50 °C for

extended periods of time.

• Please inspect the temperature label attached to the

inside of cartridge packaging to verify that your cartridge

has not been damaged in shipment. A gray circle is

acceptable, a black circle indicates that the cartridge

may have been exposed to an extreme temperature.

• Please contact Agilent Technical Support if your

cartridge is delivered with a temperature indicator

that is black.

• Do not use the flow meter to measure corrosive gases.

WARNING

• Use only a 5 V DC, 0.5 A USB power source and the

supplied USB cable to run this device.

• Do not use the ADM flow meter as safety equipment.

ADM Flow Meter

Notes, Cautions, and Warnings

Agilent CrossLab CS ADM Flow Meter Operation Manual 9

WARNUNGWARNUNG

• Verwenden Sie zum Aufladen dieses Geräts

ausschließlich eine 5v DC, 0,5A USB-Stromquelle und das

mitgelieferte USB-Kabel.

• Verwenden Sie den ADM-Durchflussmesser nicht als

Sicherheitsausrüstung.

ATTENTION

• Utilisez uniquement une source d'alimentation USB 5 V

CC, 0,5 A et le câble USB fourni pour charger cet appareil.

• N’utilisez-pas le débitmètre ADM comme équipement

de sécurité.

ATTENZIONE

• Per caricare questo dispositivo, utilizzare solo una fonte

di alimentazione USB da 5 V CC, 0,5 A e il cavo USB

in dotazione.

• Non utilizzare il misuratore di portata ADM come

apparecchiatura di sicurezza.

ADVERTENCIA

• Para cargar este dispositivo, use solamente una fuente

de alimentación USB de 0,5A, DC 5V y el cable de

alimentación suministrado.

• No utilice el flujómetro ADM como equipo de seguridad.

警告

•仅使用 5v DC、0.5A USB 电源和随附的 USB 电缆为本设

备充电。

•请勿将 ADM 流量计用作安全设备。

ADM Flow Meter

Principles of Operation

10 Agilent CrossLab CS ADM Flow Meter Operation Manual

Principles of Operation

The ADM flow meter provides continuous, real-time

measurements of dry gas flows, such as those used for gas

chromatography. Unlike bubble flow meters, the flow meter

operates without liquids, bubbles, or glass parts. When

activated, a solenoid actuated valve interrupts the gas flow

momentarily. The gas flow moves a diaphragm in proportion to

the flow rate. This movement is transformed by the flow

meter's electronics into a digital value, which is displayed on the

flow meter's screen. The flow meter provides two different

types of flow measurements: volumetric flow (mL/min) and

mass flow reported in standard cubic centimeters per minute

(sccm). Mass flow values are calculated from the volumetric

measurements by correcting for ambient temperature and

atmospheric pressure, and reporting the flow rate referenced to

0 °C and one atmosphere of pressure, using digital temperature

and pressure sensors installed in the mainframe of the

flow meter.

The flow meter uses a replaceable cartridge that contains all

parts subject to calibration. This eliminates the need to ship the

entire meter back to the factory to maintain its calibration. The

cartridge calibration is valid for a period of one year from its first

use. A new, calibrated cartridge can be ordered in advance, and

installed when necessary.

When the flow meter is powered on with a new cartridge

installed, the current date is written to the cartridge’s memory

based on the mainframe’s internal clock. Each time the flow

meter is turned on, the meter will compare the current date to

the initial turn on date of the cartridge. If the initial turn on date

is more than a year from the current date, the flow meter will

flash a notification to the user that the calibration has expired.

The flow meter will still function with an expired calibration. This

eliminates downtime, enabling you to keep working. See

Installing and Replacing the Cartridge on page 31.

The flow meter is powered by three AA alkaline batteries. Power

can also be supplied via the micro USB port located on the side

of the unit.

Andere Handbücher für CrossLab CS

Inhaltsverzeichnis

Andere Agilent Technologies Messgerät Handbücher

Agilent Technologies

Agilent Technologies 8712ET Bedienungsanleitung

Agilent Technologies

Agilent Technologies 4200 FlexScan Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1731B Bedienungsanleitung

Agilent Technologies

Agilent Technologies FieldFox N9912A Bedienungsanleitung

Agilent Technologies

Agilent Technologies ENA Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies E5080 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies N5225-60114 Installations- und Betriebshandbuch

Agilent Technologies

Agilent Technologies 8453 Bedienungsanleitung

Agilent Technologies

Agilent Technologies U3051C Betriebsanleitung

Agilent Technologies

Agilent Technologies 1660C Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies N1913a Bedienungsanleitung

Agilent Technologies

Agilent Technologies OmniBER 725 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 4263B Bedienungsanleitung

Agilent Technologies

Agilent Technologies Agile or Elusive Signals Using Handbuch

Agilent Technologies

Agilent Technologies E4980A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 4263B Bedienungsanleitung

Agilent Technologies

Agilent Technologies FRG-700 Bedienungsanleitung

Agilent Technologies

Agilent Technologies ADM series Bedienungsanleitung

Agilent Technologies

Agilent Technologies E8362A Bedienungsanleitung

Agilent Technologies

Agilent Technologies Agilent 86120B Bedienungsanleitung

Agilent Technologies

Agilent Technologies E4443A Kurzanleitung

Agilent Technologies

Agilent Technologies 1664A Bedienungsanleitung

Agilent Technologies

Agilent Technologies EMC Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies L4532A Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung