Agilent Technologies Agilent E5252A Bedienungsanleitung

Installation Guide

Agilent E5252A 10´12 Matrix Switch

Agilent Part No. E5252-90000

Printed in Japan January 2000

Edition 2

2 Agilent E5252A Installation Guide, Edition 2

Legal Notice

The information contained in this document is subject to change without notice.

This document contains information which is protected by copyright. All rights are

reserved. Reproduction, adaptation, or translation without prior written permission

is prohibited, except as allowed under the copyright laws.

• Product Warranty

Agilent Technologies warrant Agilent Technologies hardware, accessories and

supplies against defects in materials and workmanship for the period of one year

from the warranty start date specified below. If Agilent Technologies receive

notice of such defects during the warranty period, Agilent Technologies will, at

its option, either repair or replace products which prove to be defective.

Replacement products may be either new or like-new.

Warranty service of this product will be performed at Agilent Technologies.

Buyer shall prepay shipping charges to Agilent Technologies and Agilent

Technologies shall pay shipping charges to return the product to Buyer.

However, Buyer shall pay all shipping charges, duties, and taxes for products

returned to Agilent Technologies from another country.

Agilent Technologies do not warrant that the operation of Agilent Technologies

products will be uninterrupted or error free. If Agilent is unable, within a

reasonable time, to repair or replace any product to a condition as warranted,

customer will be entitled to a refund of the purchase price upon prompt return of

the product.

The Agilent Technologies products may contain remanufactured parts

equivalent to new in performance or may have been subject to incidental use.

The warranty period begins on the date of delivery or on the date of installation

if installed by Agilent Technologies. If customer schedules or delays Agilent

Technologies installation more than 30 days after delivery, warranty begins on

the 31st day from delivery.

Warranty does not apply to defects resulting from (a) improper or inadequate

maintenance or calibration, (b) software, interfacing, parts or supplies not

supplied by Agilent Technologies, (c) unauthorized modification or misuse, (d)

operation outside of the published environmental specifications for the product,

or (e) improper site preparation or maintenance.

Agilent E5252A Installation Guide, Edition 2 3

To the extent allowed by local law, the above warranties are exclusive and no

other warranty or condition, whether written or oral, is expressed or implied and

Agilent Technologies specifically disclaim any implied warranties or conditions

of merchantability, satisfactory quality, and fitness for a particular purpose.

Agilent Technologies will be liable for damage to tangible property per incident

up to the greater of $300,000 or the actual amount paid for the product that is the

subject of the claim, and for damages for bodily injury or death, to the extent

that all such damages are determined by a court of competent jurisdiction to

have been directly caused by a defective Agilent Technologies product.

To the extent allowed by local law, the remedies in this warranty statement are

customer’s sole and exclusive remedies. Expect as indicated above, in no event

will Agilent Technologies or its suppliers be liable for loss of date or for direct,

special, incidental, consequential (including lost profit or date), or other damage,

whether based in contract, tort, or otherwise.

For consumer transactions in Australia and New Zealand: the warranty terms

contained in this statement, except to the extent lawfully permitted, do not

exclude, restrict or modify and are in addition to the mandatory statutory rights

applicable to the sale of this product to you.

•Assistance

Product maintenance agreements and other customer assistance agreements are

available for Agilent Technologies products.

For any assistance, contact your nearest Agilent Technologies Sales Office.

•Certification

Agilent Technologies Inc. certifies that this product met its published

specifications at the time of shipment from the factory. Agilent further certifies

that its calibration measurements are traceable to the National Institute of

Standards and Technology (NIST), to the extent allowed by the Institute’s

calibration facility, and to the calibration facilities of other International

Standards Organization members.

4 Agilent E5252A Installation Guide, Edition 2

•Safety Symbols

The general definitions of safety symbols used on equipment or in manuals are

listed below.

Instruction manual symbol: the product will be marked with this symbol when it

is necessary for the user to refer to the instruction manual in order to protect

against damage to the instrument.

Indicates dangerous voltage and potential for electrical shock. Do not touch

terminals that have this symbol when instrument is on.

Protective conductor terminal. For protection against electrical shock in case of

a fault. Used with field wiring terminals to indicate the terminal which must be

connected to ground before operating equipment.

Frame or chassis terminal. A connection to the frame (chassis) of the equipment

which normally includes all exposed metal structures.

Indicates earth (ground) terminal.

Alternating current.

Direct current.

ON (Supply).

OFF (Supply).

STANDBY (Supply).

Means INSTALLATION CATEGORY I. Measurement terminals on the rear

panel comply with INSTALLATION CATEGORY I.

WARNING The warning sign denotes a hazard. It calls attention to a procedure, practice,

condition or the like, which, if not correctly performed or adhered to, could

result in injury or death to personal.

CAUTION The caution sign denotes a hazard. It calls attention to an operating procedure,

practice, condition or the like, which, if not correctly performed or adhered to, could

result in damage to or destruction of part or all of the product.

CAT 1

Agilent E5252A Installation Guide, Edition 2 5

Printing History

Edition 1: November 1995

Edition 2: January 2000

6 Agilent E5252A Installation Guide, Edition 2

Product Description

Agilent E5252A 10´12 Matrix Switch is a 10-input to 12-output switching matrix

card for Agilent E5250A Low Leakage Switch Mainframe. The E5252A is designed

for semiconductor dc parametric measurement applications that need to switch some

instruments connected to Device Under Test (DUT), or need to scan instrument

input/output for many DUTs, automatically.

The E5250A can be installed with maximum four E5252As. And the input terminals

of the E5252As are connected together inside the E5250A. So, the E5250A can also

configure a 10´24 matrix (two E5252As), 10´36 matrix (three E5252As), and

10´48 matrix (four E5252As).

The E5252A block diagram and output connectors are shown below:

Agilent E5252A Block Diagram

1234567891011 12

INPUT

OUTPUT

SMU1

SMU2

SMU3

SMU4

SMU5

HF1

CV1

SMU6

HF2

CV2

Agilent E5252A Installation Guide, Edition 2 7

Agilent E5252A Output Ports

WARNING Do not touch the force and guard terminals of the output connectors while the

E5250A is turned on. Dangerous voltages up to the maximum input voltage

may be present at the output connectors.

8 Agilent E5252A Installation Guide, Edition 2

Installation

This section describes how to install the E5252A card into the E5250A Mainframe.

You can install the card in card slots 1 to 4 of the E5250A easily. The following

procedure explains the card installation and removal.

WARNING Only qualified service personnel should install the E5252A. Before removing or

installing the cards, disconnect the following from the rear side of the E5250A:

1. Disconnect the power cable.

2. Disconnect all cables from input/output terminals.

CAUTION When the E5252A is shipped from factory, it has been confirmed that the E5252A

satisfies its specifications.

But after you install the E5252A into your E5250A, the specifications of your

E5250A with the card are not guaranteed.

For verifying the specifications, contact your nearest Agilent Technologies Service

Center.

CAUTION Use clean handling and anti-static procedures when removing, configuring, and

installing the plug-in cards. The cards contain components that can be damaged by

static electricity.

CAUTION Be careful about the module pins used for internal connection to the E5250A. The

pins can be damaged easily.

Agilent E5252A Installation Guide, Edition 2 9

Procedure:

1. Turn off the E5250A, then wait at least 10 seconds before you remove or install

a card.

2. Remove blank panel or card from the slot where you want to install the new card

as follows:

•To remove blank panel, do as follows:

Loosen the screws on both the left and right edges of the blank panel by

using the wrench furnished with the E5252A, then remove the blank panel.

•To remove a card, do as follows:

a. Screw the Module Extractor into the screw hole for the extractor. See

figure below. Module Extractor is furnished with the E5250A.

b. Loosen the screws on left and right edges of the card by using the wrench

furnished with the E5252A.

c. Gently pull the Module Extractor to extract the card from the card slot.

Module Extractor and Location of the Screw Hole

3. Install the card as follows:

a. Align the card with the left and right slot guide rails. The component side

should be facing up.

b. Push the card into the slot until you feel it seat firmly into the connector at

the back of the card slot.

c. Screw in the screws on the left and right edges of the card by using the

wrench furnished with the E5252A.













10 Agilent E5252A Installation Guide, Edition 2

4. Execute the Relay Test as follows:

NOTE To execute the relay test, you need the Relay Test Adapter (Agilent E5250A Option

301). Prepare the Relay Test Adapter.

a. Attach the Relay Test Adapter to the E5250A input connectors as shown in

the following figure.

b. Set switch on the Relay Test Adapter to Relay Test position.

c. Make sure no output cables are connected to any cards in the E5250A

mainframe.

d. Turn on the E5250A.

e. Press the Local/Self Test key on the E5250A front panel. The Relay Test

executes.

f. Wait until the LED in Local/Self Test key turns off.

Relay Test Adapter Connection

NOTE After executing the relay test, if the Fail LED turns on, the cause is one of the

following:

a. The Relay Test Adapter is not connected.

b. A plug-in card may be defective. Contact your nearest Agilent Technologies

Service Center.

Relay Test Adapter

Inhaltsverzeichnis

Andere Agilent Technologies Schalten Handbücher

Agilent Technologies

Agilent Technologies L4445A Bedienungsanleitung

Agilent Technologies

Agilent Technologies Agilent 34980A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 86062C Bedienungsanleitung

Agilent Technologies

Agilent Technologies 34950A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 3488A Kurzanleitung

Agilent Technologies

Agilent Technologies 34901A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8710 Series Service-Handbuch

Agilent Technologies

Agilent Technologies Agilent 34980A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 86060A Bedienungsanleitung

Agilent Technologies

Agilent Technologies Agilent E6474A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 34972A Bedienungsanleitung

Agilent Technologies

Agilent Technologies Series N6700 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 34970A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 86060C Series Bedienungs- und Sicherheitshinweise

Agilent Technologies

Agilent Technologies Agilent E5250A Bedienungsanleitung

Agilent Technologies

Agilent Technologies B2200A Bedienungsanleitung

Agilent Technologies

Agilent Technologies Agilent 34980A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 75000 Series C Bedienungsanleitung

Agilent Technologies

Agilent Technologies U2121A-101 RF Bedienungsanleitung

Agilent Technologies

Agilent Technologies Agilent 34980A Bedienungsanleitung

Agilent Technologies

Agilent Technologies E1463A Betriebsanleitung

Agilent Technologies

Agilent Technologies 86060C Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 11713A Service-Handbuch

Agilent Technologies

Agilent Technologies Switch/Measure Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung