Agilent Technologies 5DX II Series Bedienungsanleitung

Agilent Technologies

5/16/02

Agilent 5DX Series II

Installation Guide

E7200-90023

Revision A.1

April, 1998

E7200-90034

Emergency Shut Down Procedure

In the event of a disaster or system emergency, shut down the Agilent

5DX by pressing one of the Emergency Stop Buttons, as indicated in

Figure T-1:

For additional information on Safety and the Agilent 5DX System, see

the Safety Summary in the Agilent 5DX Series II Service Guide.

Figure T-3 Emergency Stop Button Locations

WARNING 120 Volt AC Power Connections are for Agilent Installed

Accessories ONLY. Do not use these connections as utility

outlets. Improper handling of these connections can result in

electrical shock.

Emergency Stop

Release Keys

Emergency Stop Button

(Locking Switch)

Emergency Stop Button locks

when pressed

X-ray On Indicator

- iii

Agilent 5DX Series II Installation Guide Contents

Emergency Shut Down Procedure ii

Warranty and Regulatory Data v

Safety Information ix

SAFETY SYMBOLS ix

Electromagnetic Compatibility Requirements xii

Emergency Stop xiii

Preparing for 5DX Installation 1

System Arrival, Inspection and Placement 3

System Hardware Installation 9

System Performance Verification Procedure 24

Power Checks 24

System Startup 27

Panel Handling 30

Wiring Configuration 45

200-240 Volt 1-Phase Earthed 50

200-240 Volt 1-Phase Non-Earthed 52

200-240 Volt 3-Phase Delta with Phase Junction Earthed 54

200 - 220 Volt 3-Phase Wye or Delta 56

380-415 Volt 3-Phase Wye with Neutral 58

SMEMA Interface 61

X-RAY Safety Reference 67

- iv

5/16/02

Notices

Warranty and Regulatory Data

NOTICE

This manual is provided “as is” and is subject to change without notice.

AGILENT TECHNOLOGIES MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT,

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Agilent shall not be liable for errors contained

herein, nor for direct, indirect, general, special, incidental or consequential damages in connection with the furnishing,

performance, or use of this material.

Adobe™ is a trademark of Adobe Systems Incorporated which may be registered in certain jurisdictions.

Microsoft®is a U.S. registered trademark of Microsoft Corp.

Windows®and MS Windows®are U.S. registered trademarks of Microsoft Corp.

Printed in USA

E7200-90034 Printed: April, 1998

Manual Printing History And System Software Revisions:

This page lists this manual's printing history and the system's software revisions. If you receive manual updates or system

software revisions, a new Printing History Page will accompany the updates and revisions. It is important that you insert the

new Printing History Page in the manual and remove the old one.

Agilent 5DX Installation Guide

Software Revision Manual Revision

---------------------------------------------------------------

5.2 Rev. A, April, 1998

‘

AGILENT TECHNOLOGIES WARRANTY STATEMENT

Agilent PRODUCT DURATION OF WARRANTY

Agilent 5DX System and Accessories 1 (One) Year

1. Agilent warrants Agilent hardware, accessories and supplies against defects in materials and workmanship for the

period specified above. If Agilent receives notice of such defects during the warranty period, Agilent will, at its

option, either repair or replace products which prove to be defective. Replacement products may be either new or

like-new.

2. Agilent warrants that Agilent software will not fail to execute its programming instructions, for the period specified

above, due to defects in material and workmanship when properly installed and used. If Agilent receives notice of

such defects during the warranty period, Agilent will replace software media which does not execute its

programming instructions due to such defects.

3. Agilent does not warrant that the operation of Agilent products will be uninterrupted or error free. If Agilent is

unable, within a reasonable time, to repair or replace any product to a condition as warranted, customer will be

entitled to a refund of the purchase price upon prompt return of the product.

4. Agilent products may contain remanufactured parts equivalent to new in performance or may have been subject to

incidental use.

5. The warranty period begins on the date of delivery or on the date of installation if installed by Agilent. If customer

schedules or delays Agilent installation more than 30 days after delivery, warranty begins on the 31st day from

delivery.

6. Warranty does not apply to defects resulting from (a) improper or inadequate maintenance or calibration, (b)

software, interfacing, parts or supplies not supplied by Agilent, (c) unauthorized modification or misuse, (d)

operation outside of the published environmental specifications for the product, or (e) improper site preparation or

maintenance.

7. TO THE EXTENT ALLOWED BY LOCAL LAW, THE ABOVE WARRANTIES ARE EXCLUSIVE ANDNO

OTHER WARRANTY OR CONDITION, WHETHER WRITTEN OR ORAL, IS EXPRESSED OR IMPLIED

AND AGILENT SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OR CONDITIONS OF

MERCHANTABILITY, SATISFACTORY QUALITY, AND FITNESS FOR A PARTICULAR PURPOSE.

8. Agilent will be liable for damage to tangible property per incident up to the greater of $300,000 or the actual amount

paid for the product that is the subject of the claim, and for damages for bodily injury or death, to the extent that all

such damages are determined by a court of competent jurisdiction to have been directly caused by a defective

Agilent product.

9. TO THE EXTENT ALLOWED BY LOCAL LAW, THE REMEDIES IN THIS WARRANTY STATEMENT ARE

CUSTOMER'S SOLE AND EXCLUSIVE REMEDIES. EXCEPT AS INDICATED ABOVE, IN NO EVENT

WILL AGILENT OR ITS SUPPLIERS BE LIABLE FOR LOSS OF DATA OR FOR DIRECT, SPECIAL,

INCIDENTAL, CONSEQUENTIAL (INCLUDING LOST PROFIT OR DATA), OR OTHER DAMAGE,

WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE.

FOR CONSUMER TRANSACTIONS IN AUSTRALIA AND NEW ZEALAND: THE WARRANTY TERMS

CONTAINED IN THIS STATEMENT, EXCEPT TO THE EXTENT LAWFULLY PERMITTED, DO NOT EXCLUDE,

RESTRICT OR MODIFY AND ARE IN ADDITION TO THE MANDATORY STATUTORY RIGHTS APPLICABLE TO

THE SALE OF THIS PRODUCT TO YOU.

PLACE OF PERFORMANCE

A. Within Agilent service travel areas, warranty and installation services for products installed by Agilent and certain other

products designated by Agilent will be performed at Customer’s facility at no charge. Outside Agilent service travel areas,

warranty and installation services will be performed at Customer’s facility only up on Agilent’s prior agreement and

Customer shall pay Agilent’s round-trip travel expenses and applicable additional expenses for such services.

B. On-site warranty services are provided only at the initial installation point. If products eligible for on-site warranty and

installation services are removed from the initial installation point, the warranty will remain in effect only if Customer

purchases additional inspection or installation services at the new site.

C. For product warranties requiring return to Agilent, products must be returned to a service facility designated by Agilent.

The Customer shall prepay shipping charges (and shall pay all duty and taxes) for products returned to Agilent for

warranty service. Except for products returned to Customer from another country, Agilent shall pay for return of products

to Customer.

D. Installation and warranty services outside the country of initial purchase are included in Agilent’s product price only if

Customer pays Agilent international prices (defined as destination local currency price, or U.S., or Geneva Export price).

Service outside the country of initial purchase is subject to the conditions regarding Agilent service travel areas and initial

installation point described above.

LIMITATION OF REMEDIES AND LIABILITY

A. Agilent will not be liable for performance delays or for non-performance, due to causes beyond its reasonable control.

B. Products not specifically designed, manufactured or intended for sale as parts, components or assemblies for planning,

construction, maintenance, or direct operation of a nuclear facility. Customer is solely liable if Products or Support

purchased by Customer are used for these applications. Customer will indemnify and hold Agilent harmless from all loss,

damage, expense or liability in connection with such use.

C. Agilent will be liable for damage to tangible property per incident up to the greater of $300,000 or the actual charges paid

to Agilent for the product that is the subject of the claim, and for damages for bodily injury or death, to the extent that all

such damages are determined by a court of competent jurisdiction to have been directly caused by a defective Product sold

hereunder.

D. For any material breach of Support services by Agilent, Customer’s remedy and Agilent’s liability will be limited to a

refund of the related Support charges paid during the period of breach, up to a maximum of 12 months.

E. THE REMEDIES IN THIS AGREEMENT ARE CUSTOMER’S SOLE AND EXCLUSIVE REMEDIES. EXCEPT AS

INDICATED ABOVE, IN NO EVENT WILL AGILENT OR ITS SUBCONTRACTORS BE LIABLE FOR LOSS OF

DATA OR FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL (INCLUDING LOST PROFIT), OR OTHER

DAMAGE WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE.

U.S. Government Restricted Rights

The Software and Documentation have been developed entirely at private expense. They are delivered and licensed as

“commercial computer software” as defined in DFARS 252.227-7013 (Oct 1988), DFARS 252.211-7015 (May 1991) or DFARS

252.227-7014 (Jun 1995), as a “commercial item” as defined in FAR 2.101(a), or as “Restricted computer software” as

defined in FAR 52.227-19 (Jun 1987) (or any equivalent agency regulation or contract clause), whichever is applicable. You

have only those rights provided for such Software and Documentation by the applicable FAR or DFARS clause or the

Agilent standard software agreement for the product involved.

Regulatory Information

Agilent Technologies is registered with federal and state agencies to sell and service its own X-ray equipment manufactured

in Loveland, Colorado, USA. The equipment was designed, and is used, to inspect printed circuit boards only. The X-ray

equipment is classified in the United States and internationally as an “Industrial Cabinet X-ray System”. It is not large

enough for human entry. The equipment has been designed and constructed to be safely used in any area.

The Agilent 5DX System utilizes an X-ray Tube operating at 160 kilovolts, 100 microamps shielded within the lead cabinet.

The tube is rated for continuous duty operation with beam filtration of 0.07 inches Beryllium and 0.010 inches stainless

steel.

The lead cabinet is fully interlocked such that the main power to the X-ray Tube is removed when any access panel is

opened.

When the Agilent 5DX System is installed at the customer’s site, the equipment is surveyed by trained service people. A full

radiation safety survey is performed and a report generated. The survey is made using a Geiger Mueller and a health physics

ion chamber according to procedures on record with the CDRH.

The end user is responsible for registering the equipment with their local and state authorities.

Agilent Technologies warrants that the Agilent 5DX automated process test systems meets X-ray safety regulations in the

following countries:

Canada Reference Statutes of Canada Chapter R-1, Chapter 1370, Schedule 1, Section 15, Schedule II and Part XV.

England Reference BS5724, (ISO 9000 601-1).

Germany Reference BGBII, S.114 & Din 54113 and the “Law on the Protection Against Injury or Damage Due to X-

Rays” a.k.a. “X-Ray Decree”.

Japan Reference Ministry of Labor, Industrial Safety and Health, Law #57 and Cabinet ordinance #38.

Korea Reference Presidential Decree, Article 65, Chapter VII, of the Atomic Energy Act.

The Nordic Regions of Denmark, Finland, Iceland, Norway and Sweden,

Reference the Radiation Protection Institutes and the Radiation Protection Act.

United States

Regulation 21CFR 1010.2, 1010.3, and 1020.40 administered by the Department of Health and Human

Services, Food and Drug

Administration, Center for Devices and Radiological Health (CDRH).

Safety Information

SAFETY SYMBOLS

Warning This product produces X-radiation. Do not attempt to open any part

of the product. Exposure to X-radiation can cause serious bodily

injury. Refer all servicing to service-trained personnel.

Warning This product produces X-radiation. Do not operate this product or

turn on the X-radiation source unless all shielding is in place. Oper-

ation without shielding in place can result in serious bodily injury.

Instruction symbol affixed to

product. Indicates that the user must

refer to the manual for specific

WARNING or CAUTION

information to avoid personal injury

or damage to the product.

Alternating current

(ac).

Indicates the field wiring terminal

that must be connected to earth

ground before operating the

equipment — protects against

electrical shock in case of fault.

Direct current (dc).

Frame or chassis ground terminal —

typically connects to the equipment’s

metal frame.

Indicates hazardous

voltage.

Warning Calls attention to a procedure,

practice, or condition that could

result in bodily injury or death. !

Caution Calls attention to a

procedure, practice, or

condition that could cause

damage to equipment or

permanent loss of data.

WARNINGS

The following general safety precautions must be observed during all phases of operation, service, and repair of this

product. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety

standards of design, manufacture, and intended use of the product. Agilent Technologies assumes no liability for the

Customer’s failure to comply with these requirements.

Ground the Equipment For Safety Class 1 equipment (equipment having a protective earth terminal), an uninterruptible

safety earth ground must be provided from the mains power source to the product input wiring terminals or supplied power

cable.

DO NOT operate the product in an explosive atmosphere or in the presence of flammable gases or fumes.

For continued protection against fire, replace the line fuses(s) only with the fuse(s) of the same voltage and current rating

and type. DO NOT use repaired fuses or short-circuited fuse holders.

Keep away from live circuits: Operating personnel must not remove equipment covers or shields. Procedures involving the

removal of covers or shields are for use by service-trained personnel only. Under certain conditions, dangerous voltages

may exist even with the equipment switched off. To avoid dangerous electrical shock, DO NOT perform procedures

involving cover or shield removal unless you are qualified to do so.

DO NOT operate damaged equipment: Whenever it is possible that the safety protection features built into this product

have been impaired, either through physical damage, excessive moisture, or by any other reason, REMOVE POWER and do

not use the product until safe operation can be verified by service-trained personnel. If necessary, return the product to an

Agilent Technologies Sales and Service Office for service and repair to ensure that safety features are maintained.

Do not service or adjust alone: Do not attempt internal service or adjustment unless another person, capable of rendering

first aid and resuscitation, is present.

Do not substitute parts or modify equipment: Because of the danger of introducing additional hazards, do not install

substitute parts or perform any unauthorized modification to the product. Return the product to an Agilent Technologies

Sales and Service Office for service and repair to ensure that safety features are maintained.

Inhaltsverzeichnis

Andere Agilent Technologies Prüfgeräte Handbücher

Agilent Technologies

Agilent Technologies 85050C Handbuch

Agilent Technologies

Agilent Technologies 16034H Bedienungsanleitung

Agilent Technologies

Agilent Technologies 16034H Bedienungsanleitung

Agilent Technologies

Agilent Technologies ENA Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 85056D Handbuch

Agilent Technologies

Agilent Technologies N9360A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 54522A Bedienungsanleitung

Agilent Technologies

Agilent Technologies Medalist i3070 Series Benutzerhandbuch

Agilent Technologies

Agilent Technologies 93000 SOC Series Installationsanleitung

Agilent Technologies

Agilent Technologies U4002A Bedienungsanleitung

Agilent Technologies

Agilent Technologies U7242A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5530 Bedienungsanleitung

Agilent Technologies

Agilent Technologies N5230-60102 Installations- und Betriebshandbuch

Agilent Technologies

Agilent Technologies InfiniiVision MSO6102A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1000A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 16034E Bedienungsanleitung

Agilent Technologies

Agilent Technologies 16048G Bedienungsanleitung

Agilent Technologies

Agilent Technologies Infiniium 90000 Q-Series Handbuch

Agilent Technologies

Agilent Technologies InfiniiVision 3000 X-Series Handbuch

Agilent Technologies

Agilent Technologies 4072A Advanced Bedienungsanleitung

Agilent Technologies

Agilent Technologies 100 Bedienungsanleitung

Agilent Technologies

Agilent Technologies ACQIRIS CC103 Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2969A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 16047E Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung

Ritmix

Ritmix RAT-701 Bedienungsanleitung