Agora Models ALIEN Pack 04 Handbuch

1PB

ALIENALIEN

Pack 04

BUILD INSTRUCTIONS

STAGE 21: THE RIGHT LEG (III)

STAGE 22: THE RIGHT RIBS & THE LEG (II)

STAGE 23: THE RIGHT RIBS & THE LEG (III)

STAGE 24: THE RIGHT RIBS & THE LEG (IV)

STAGE 25: THE RIGHT RIBS &

THE RIGHT FEMUR (I)

STAGE 26: THE RIGHT RIBS &

THE RIGHT FEMUR (II)

STAGE 27: THE RIGHT RIBS &

THE RIGHT FEMUR (III)

STAGE 28: THE RIGHT RIBS &

THE RIGHT FEMUR (IV)

2PB

WARNING: Some parts are assembled using magnets. These magnets can cause serious injury if they are

swallowed. Keep away from children. If you suspect a magnet has been swallowed, seek medical help

straight away.

All parts belong to a kit. Collectors item for adults.

Not suitable for children under 14.

Some parts may have sharp edges, please handle them with care.

The installation of electronic parts must always be carried out by an adult. When replacing batteries, use

the same type of batteries.

Please ensure that the battery compartment is securely fastened before you use the model.

Used batteries should be recycled.

Please make sure to check with your local authority how batteries should be disposed of in your area.

Batteries can present a choking danger to small children and may cause serious harm if ingested. Do not

leave them lying around and keep any spare batteries locked away at all times.

Before you start...

To help you get the best out of building the Xenomorph, we’ve prepared a modellers checklist

with hints, tips and advice from our expert. The information below is aimed at making your

build as enjoyable and professional as possible right from the start.

Make sure you have good ventilation when using adhesives and to replace

caps ﬁrmly.

Always use the correct adhesives and always follow manufacturers guidance.

Apply glue sparingly and use a cocktail stick to apply so that you don’t use too

much nor apply the glue too heavily.

Work in a well lit area. Use an anglepoise lamp or similar on your work bench to ensure you

have good light whenever you’re at work.

Organise storage – stackable, labeled containers like old clean takeaway or ice-cream plastic

tubs with lids are perfect. Small parts which may not be needed until a later stage should be

kept in clear plastic and labeled bags.

Use masking tape to hold parts temporarily in place.

Only use the correct size screwdriver that ﬁts the screw head ﬁrmly.

Cut parts from a sprue (framework) with side cutters or a craft knife. Side cutters tend to be

easiest.

Use a magnet to help ﬁnd screws that have fallen on the ﬂoor.

Leave parts in the paper bags supplied until they are needed. You can write a note of the stage

and part on the paper bag too.

If a screw is tight, try turning a half turn forwards followed by a quarter turn backwards. Also, it

can sometimes help to temporarily ﬁt a screw into its hole before assembling the parts.

But most of all, enjoy your build!

3PB

ASSEMBLY GUIDE

In this stage you will continue to assemble parts of the Xenomorph’s right leg.

STAGE 21: THE RIGHT

LEG (III)

21-1

21-2

21-3

21-4

PARTS SUPPLIED

Ref. Name Qty.

21-1 Right Tibia 1

21-2 Connectors 4

Ref. Name Qty.

21-3 Magnets 8

21-4 2.3x6mm screws 10*

*A spare screw is supplied in case of loss or damage.

4PB

STAGE 21: THE RIGHT LEG (III)

21-1

16-1

15-1

14-1

21-4

20-3

20-4

21-1

20-3

16-1

15-1

Take the Right Tibia assembly

20-3 which was worked on in

the last stage. Tibia part 21-1 is

joined to this using the previously

fitted Connector 20-4, as shown.

Secure in place with a 2.3x6mm

screw 21-4.

Next, take the Right Calf

assembly 14-1 which was

last worked on in stage 16

and remove the inner parts

15-1/16-1.

The Tibia assembly 15-1/16-1 is

now joined to the assembly 20-3/

21-1. There is a tab with a hole at

the end of part 15-1 (circled) which

fits over a peg on part 20-3 (arrow).

5PB

STAGE 21: THE RIGHT LEG (III)

21-2

21-4

21-2

21-4

21-2

21-1

20-3

15-1

16-1

Fit the four Connectors

21-2 which will hold the

assemblies 15-1/16-1

and 20-3/21-1 together.

Secure each Connector

21-2 in place with two

2.3x6mm screws 21-4.

6PB

21-3

14-1

15-1

20-3

21-1

16-1

Take the Outer Calf Skin 14-1 and

glue four Magnets 21-3 firmly into

the circular recesses as shown on

the left. It doesn’t matter which

way round the magnets are fitted.

Place the assembly 15-1/

16-1/20-3/21-1 over the

calf assembly 14-1.

STAGE 21: THE RIGHT LEG (III)

7PB

STAGE 21 IS COMPLETE

21-3

20-3

21-1

Further parts including a set of

magnets have been fitted to the

right leg.

Four magnets are now fitted into

the circular recesses in parts

20-3/21-1, as shown above.

When fitted correctly, they should

be attracted to the magnets

underneath on the Calf Skin 14-1.

When certain that the magnets are

correctly orientated, glue in place.

STAGE 21: THE RIGHT LEG (III)

8PB

Ref. Name Qty.

22-1 Calf Protector 1

22-2 Right Rib 1

Ref. Name Qty.

22-3 Pipe A1 1

22-4 2.3x6mm screws 4*

ASSEMBLY GUIDE

In this stage you will continue to work on the right ribs

and leg of the Xenomorph.

STAGE 22: THE RIGHT

RIBS & THE LEG (II)

22-1

22-3 22-4

22-2

PARTS SUPPLIED

*A spare screw is supplied in case of loss or damage.

9PB

STAGE 22: THE RIGHT RIBS & THE LEG (II)

22-2

22-3 (A1)

22-1

22-4

22-2

20-2

19-3

19-2

Take the rib support assembly

19-3 which was worked on in pack

3 - stage 20. Fit the raised screw

socket on Right Rib 22-2 into the

corresponding hole on rib support

19-3, as shown.

Turn the assembly over and

x Right Rib 22-2 in place

with a 2.3x6mm screw 22-4.

Put the assembly aside.

Next, take the Calf Protector 22-1

and the Pipe A1 22-3. The tabs

on the pipe are arranged so that

the pipe will only fit correctly one

way round. After test-fitting, apply

a little glue to the tabs and fix

firmly in place.

10 PB

STAGE 22: THE RIGHT RIBS & THE LEG (II)

STAGE 22 IS COMPLETE

22-4

4-6

22-4

22-1

ANOTHER RIB HAS BEEN CONNECTED

AS WELL AS FURTHER WORK ON THE

CALF PROTECTOR.

Take the Calf Protector 4-6, which was

assembled in pack 1 - stage 4, along with

Calf Protector 22-1. Align the holes at

one end of part 4-6 over the raised screw

sockets on part 22-1, as shown. Secure

the parts together using two 2.3x6mm

screws 22-4.

Andere Agora Models Spielzeug Handbücher

Agora Models

Agora Models OPTIMUS PRIME Pack 05 Handbuch

Agora Models

Agora Models Mitsubishi A6M ZERO Fighter Handbuch

Agora Models

Agora Models FERRARI 312 T4 Bedienungsanleitung

Agora Models

Agora Models Hachette Mitsubishi A6MZERO FIGHTER Handbuch

Agora Models

Agora Models JAGUAR E-TYPE Handbuch

Agora Models

Agora Models Hachette Mitsubishi A6MZERO FIGHTER Handbuch

Agora Models

Agora Models FERRARI 312 T4 Bedienungsanleitung

Agora Models

Agora Models Hachette Mitsubishi A6MZERO FIGHTER Handbuch

Agora Models

Agora Models Mitsubishi A6M ZERO Fighter Handbuch

Agora Models

Agora Models ALIEN Pack 03 Handbuch

Agora Models

Agora Models Lamborghini MIURA Handbuch

Agora Models

Agora Models OPTIMUS PRIME Pack 04 Handbuch

Agora Models

Agora Models Mitsubishi A6M ZERO Fighter Handbuch

Agora Models

Agora Models OPTIMUS PRIME Pack 01 Handbuch

Agora Models

Agora Models CORVETTE STING RAY 1963-Z06/N03 Handbuch

Agora Models

Agora Models OPTIMUS PRIME Handbuch

Agora Models

Agora Models Mitsubishi A6M ZERO Fighter Handbuch

Agora Models

Agora Models FERRARI 312 T4 Bedienungsanleitung

Agora Models

Agora Models Mitsubishi A6M ZERO Fighter Handbuch

Agora Models

Agora Models OPTIMUS PRIME Pack 02 Handbuch

Agora Models

Agora Models Mitsubishi A6M ZERO Fighter Handbuch

Agora Models

Agora Models Bismarck 06 Handbuch

Agora Models

Agora Models OPTIMUS PRIME Pack 03 Handbuch

Agora Models

Agora Models ALIEN Handbuch

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Handbuch

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

Meccano

Meccano 15103 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung