Agora Models ALIEN Handbuch

1PB

ALIENALIEN

STAGE 01: THE UPPER JAW

STAGE 02: THE LOWER JAW

STAGE 03: THE SKULL & JAWBONE

STAGE 04: THE TIBIA & RETRACTABLE JAW

Pack 01

BUILD INSTRUCTIONS

2PB

To help you get the best out of building the Xenomorph, we’ve prepared a modellers checklist

with hints, tips and advice from our expert. The information below is aimed at making your

build as enjoyable and professional as possible right from the start.

Make sure you have good ventilation when using adhesives and to replace caps ﬁrmly.

Always use the correct adhesives and always follow manufacturers guidance.

Apply glue sparingly and use a cocktail stick to apply so that you don’t use too much nor apply

the glue too heavily.

Work in a well lit area. Use an anglepoise lamp or similar on your work bench to ensure you

have good light whenever you’re at work.

Organise storage – stackable, labeled containers like old clean takeaway or ice-cream plastic

tubs with lids are perfect. Small parts which may not be needed until a later stage should be

kept in clear plastic and labeled bags.

Use masking tape to hold parts temporarily in place.

Only use the correct size screwdriver that ﬁts the screw head ﬁrmly.

Cut parts from a sprue (framework) with side cutters or a craft knife. Side cutters tend to be

easiest.

Use a magnet to help ﬁnd screws that have fallen on the ﬂoor.

Leave parts in the paper bags supplied until they are needed. You can write a note of the stage

and part on the paper bag too.

If a screw is tight, try turning a half turn forwards followed by a quarter turn backwards. Also, it

can sometimes help to temporarily ﬁt a screw into its hole before assembling the parts.

But most of all, enjoy your build!

WARNING: Some parts are assembled using magnets. These magnets can cause serious injury if they are

swallowed. Keep away from children. If you suspect a magnet has been swallowed, seek medical help

straight away.

All parts belong to a kit. Collectors item for adults.

Not suitable for children under 14.

Some parts may have sharp edges, please handle them with care.

The installation of electronic parts must always be carried out by an adult. When replacing batteries, use

the same type of batteries.

Please ensure that the battery compartment is securely fastened before you use the model.

Used batteries should be recycled.

Please make sure to check with your local authority how batteries should be disposed of in your area.

Batteries can present a choking danger to small children and may cause serious harm if ingested. Do not

leave them lying around and keep any spare batteries locked away at all times.

Before you start...

3PB



Some parts of the model are attached using screws whilst some

simply push-t together. Other parts will need to be glued in

place using superglue (Cyanoacrylate or CA). Always follow the

manufacturers guidelines and warnings, apply sparingly and use in a

well ventilated space. Superglue gel (thick superglue) can be applied

with pin-point accuracy to the relevant surface using a cocktail stick.

Where possible, parts should be test-tted in place before glueing.

The instructions are numbered to indicate the correct order of

construction and also include tips and tricks to make the assembly

of the model as easy as possible.

To protect the paint nish on the components use a clean piece of

white paper on your work surface to build on.

Always read through the instructions carefully and study the

illustrations before starting the assembly.

ASSEMBLY GUIDE

The rst stage of the model’s assembly starts with the upper jaw,

which will become part of the Xenomorph’s skull.

STAGE 1: THE UPPER JAW

PARTS SUPPLIED

Ref. Name Qty.

1-1 Skull A 1

1-2 Upper Jaw A 1

1-3 Upper Jaw B 1

1-4 Upper Tooth 1 A 1

1-5 Upper Tooth 2 B 1

1-6 Upper Tooth 3 C 1

1-7 Upper Teeth 4 D 1

1-8 Upper Tooth 5 E 1

1-9 Upper Tooth 6 F 1

1-10 Upper Tooth 7 G 1

1-11 Screwdriver 1

1-12 Screws 2x6mm 4*

1-1 1-2

1-3

1-4 1-5 1-6 1-7 1-8 1-9 1-10

1-11 1-12

* A spare screw is also supplied in case of loss or damage.

4PB

1-2

1-1

1-6 (C)

1-5 (B)

1-4 (A)

1-3

1-12

STAGE 1: THE UPPER JAW

EXPERT TIP: If the screws

are difcult to t, it could be

because they are cutting a thread

as they are being screwed in. If this

should be the case, try turning the

screw forwards half a turn, then

back a quarter of a turn. Repeat

this process until the screw is

rmly secured in place.

To begin the assembly, place the Skull

1-1 upside down on the work surface.

Orientate the Upper Jaw A 1-2 so that

the three screw holes align with the

clear raised sockets on Skull part 1-1.

Using the Screwdriver 1-11, or similar,

x the two parts together with three

2x6mm screws 1-12. Ensure the parts

t snugly together and the screws are

fully seated.

Place the Upper Jaw B 1-3 on a at

surface with the teeth sockets facing

upwards. The teeth are individually

embossed with a letter to help

identify them. The Teeth 1-4 (A),

1-5 (B) and 1-6 (C) are tted into

their corresponding sockets on the

right hand side, as shown. Test-t

the teeth, noting how the sockets

are individually shaped. When you

are happy with the t, apply a small

amount of superglue in their sockets

and secure the teeth rmly in place. A

cocktail stick or similar is useful when

applying small amounts of glue.

5PB

1-8 (E)

1-9 (F)

1-10 (G)

1-3



Parts that look similar often have letters or markings on them to help

differentiate between them. For example, the teeth in this stage have the

letters A to G embossed on them.

1-4 (A) 1-5 (B) 1-6 (C) 1-7 (D) 1-8 (E) 1-9 (F) 1-10 (G)

STAGE 1: THE UPPER JAW

In a similar way to the previous step,

t the remaining Teeth 1-8 (E),

1-9 (F) and 1-10 (G) into their

corresponding sockets in the Upper

Jaw B 1-3.

6PB

STAGE 1: THE UPPER JAW



The construction uses several types of screw which

differ in size, colour and material. The screws are

supplied in separate packaging and a spare is

usually included for each type. Keep these extra

screws safe and labelled in case a replacement is

required.

STAGE 1 IS COMPLETE

1-7 (D)

1-3

1-2

The Upper Teeth 1-7 (D) are tted

into the central cavity at the front of

the Upper Jaw 1-3. After test-tting,

apply a small drop of superglue and

x the teeth in place.

The Upper Jaw B 1-3 is fitted into

the Upper Jaw A 1-2, as shown.

Test-fit the large rectangular peg

on part 1-3 into the corresponding

rectangular recess on the underside

of part 1-2. Apply a little superglue

to the peg and secure the parts

firmly together.

7PB

ASSEMBLY GUIDE

2-1 2-2 2-4 2-3

2-5 2-6 2-7 2-8

2-9 2-10 2-11

In this stage you will assemble the lower jaw pieces and

parts of the retractable jaw.

STAGE 2: THE LOWER JAW

PARTS SUPPLIED

Ref. Name Qty

2-1 Lower Jaw A 1

2-2 Lower Jaw B 1

2-3 Lateral Lower Jaw A (left) 1

2-4 Lateral Lower Jaw B (right) 1

2-5 Retractable Jaw 1 1

2-6 Retractable Jaw 2 1

Ref. Name Qty

2-7 Retractable Jaw 3 1

2-8 Retractable Jaw Gearbox 1

2-9 Connecting Pin 1

2-10 Spring A 1

2-11 Screws 2.3x6mm 3*

* A spare screw is also supplied in case of loss or damage.

8PB

The Retractable Jaw Gearbox 2-8

is also needed in this step. Turn the

Jaw assembly over and firmly push

the rectangular peg on the Gearbox

2-8 into the matching recess in Jaw

part 2-5;this is a push fit connection.

Keep the assembly safely aside until it

is needed in the next stage.

Next, take Retractable Jaw part 2-5,

the Spring 2-10 and two 2.3x6mm

screws 2-11 and arrange them as

shown. Push one end of the Spring

2-10 onto the cross shaped peg

inside Jaw 2-5. Join the two halves

of the Retractable Jaw together

taking care that the other end of the

Spring 2-10 fits into the circular

recess in Jaw part 2-7. Secure

the two parts together using two

2.3x6mm screws 2-11.

2-6

2-7

2-9

2-7

2-6

2-5

2-6

2-7

2-8

2-10

2-11

STAGE 2: THE LOWER JAW

Place parts 2-6, 2-7 and 2-9 on

the work surface, as shown. The

Retractable Jaw 2-6 fits between

the end of Jaw part 2-7. Align the

holes in the two parts and push the

Connecting Pin 2-9 through the

holes to join the parts together.

9PB

Take the Lower Jaw parts 2-1 and

2-2. Note how the rectangular peg on

Jaw 2-2 ts into the matching recess

on Lower part 2-1. Apply a little glue

in the recess and press the two parts

rmly together. Make sure the parts are

secured together before continuing.

STAGE 2: THE LOWER JAW

2-2

2-1

2-3



Protect painted parts from damage during

assembly by working on a cutting mat or a

sheet of cardboard. To clean components,

use a soft, dry cloth so as not to damage your

Xenomorph. Remove dust from intricate items

using a soft brush.

The Lower Lateral Jaw 2-3

is fitted to the left side of

the Jaw 2-1. There are five

circular sockets on Jaw part

2-1 into which pegs on Jaw

2-3 fit. Jaw part 2-1 may

need to be bent slighty for

the pegs to align. As part

2-3 will need to be removed

in a later stage, do not glue

in place. If necessary, use a

small piece of masking tape

to temporarily hold the part

in place.

10 PB

STAGE 2 IS COMPLETE

2-1

2-4

Work has now been done on the retractable jaw

along with other parts of the lower jaw. To keep

the parts of your model in perfect condition, avoid

contact with other objects and keep them in a safe

place out of direct sunlight so they do not warp.

STAGE 2: THE LOWER JAW

In a similar way, fit the Lateral Lower

Jaw 2-4 to the right hand side of

the Jaw 2-1. Again, do not glue in

place and if necessary, use a small

piece of masking tape to temporarily

hold the part in place.

Inhaltsverzeichnis

Andere Agora Models Spielzeug Handbücher

Agora Models

Agora Models FDNY FIRE TRUCK TOWER LADDER 9 Handbuch

Agora Models

Agora Models Lamborghini MIURA Handbuch

Agora Models

Agora Models Mitsubishi A6M ZERO Fighter Handbuch

Agora Models

Agora Models FERRARI 312 T4 Bedienungsanleitung

Agora Models

Agora Models FERRARI 312 T4 Bedienungsanleitung

Agora Models

Agora Models Mitsubishi A6M ZERO Fighter Handbuch

Agora Models

Agora Models Hachette Mitsubishi A6MZERO FIGHTER Handbuch

Agora Models

Agora Models LONDON TRANSPORT ROUTEMASTER RM 857 Handbuch

Agora Models

Agora Models OPTIMUS PRIME Pack 01 Handbuch

Agora Models

Agora Models Bismarck 08 Handbuch

Agora Models

Agora Models FERRARI 312 T4 Bedienungsanleitung

Agora Models

Agora Models Bismarck 06 Handbuch

Agora Models

Agora Models OPTIMUS PRIME Pack 03 Handbuch

Agora Models

Agora Models Mitsubishi A6M ZERO Fighter Handbuch

Agora Models

Agora Models OPTIMUS PRIME Pack 05 Handbuch

Agora Models

Agora Models ALIEN Pack 04 Handbuch

Agora Models

Agora Models OPTIMUS PRIME Handbuch

Agora Models

Agora Models OPTIMUS PRIME Pack 02 Handbuch

Agora Models

Agora Models Mitsubishi A6M ZERO Fighter Handbuch

Agora Models

Agora Models ALIEN Pack 03 Handbuch

Agora Models

Agora Models Mitsubishi A6M ZERO Fighter Handbuch

Agora Models

Agora Models JAGUAR E-TYPE Handbuch

Agora Models

Agora Models CORVETTE STING RAY 1963-Z06/N03 Handbuch

Agora Models

Agora Models Hachette Mitsubishi A6MZERO FIGHTER Handbuch

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Handbuch

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

Meccano

Meccano 15103 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung