AirLive MD-3025-IVS Bedienungsanleitung
MD-3025-IVS
iMotion Detection
Guide
Version 1.0
MD-3025-IVS iMotion Detection Setup Guide
1
MD-3025-IVS
iMotion Detection Guide
1. Overview
The MD-3025-IVS has built-in video analytic function for intelligent motion detection. It is a
standalone function built into the camera’s firmware without the need for external software
or device. The iMotion detection function can be used to detect specific or any moving
objects. This guide will focus on using MD-3025-IVS’s “iMotion Detection” function to do
moving object detection in places like warehouse, school, store or super market.
There are 3 specific enhancements in iMotion Detection compared with Motion Detection.
Ability to distinguish motion from people, vehicle, or user defined object size.
Define the detection areas with polygons.
Ability to define event interval.
The iMotion Detection works by defining 1~4 zones on the video image. When a person or
object crosses the border or moves into the zone, the camera will detect the object
immediately.
The important factors for successful iMotion Detection installations are:
Choose the appropriate installation location and avoid any obstacle like shadow of tree
or building showing in the detecting area.
Choose the appropriate resolution and frame rate.
We will guide you through the procedure in the following articles.
MD-3025-IVS iMotion Detection Setup Guide
2
2. Hardware Installation Guidelines
It is recommended to have at least 2.6 meter of vertical clearance (from floor to ceiling)
for best performance. However, if your environment cannot meet the recommended
conditions, it can still work with reasonable accuracy.
The followings are basic installation guidelines for best iMotion Detection.
1. Prevent from any shadow comes into detection area.
2. Avoid any moving merchandise, decoration or flash lights in the detection area.
3. Make sure there is enough illumination.
MD-3025-IVS iMotion Detection Setup Guide
3
3. Camera Configuration
3.1 Finding camera using AirLive IP Wizard
The IPCAM’s default IP address is 192.168.1.100，but this address can change when there
is DHCP server(router) in your network. Therefore, please install AirLive IP wizard to find
your camera.
1. Install the “AirLive IP Wizard” from the installation CD or download it from this link.
2. Run the “setup.exe” and open the AirLive IP Wizard.
3. The IP Wizard will auto search and list out the camera found. Double click on the camera
that you want to configure.
4. The IPCAM’s web configuration will open automatically after double click. Please enter
the “admin” for username and “airlive” for password.
5. After entering the correct username and password. You will enter the camera’s web
configuration page. When prompted to install “Media Control” from “OvisLink Corp”,
please select “Yes” to install.
3.2 Enable Camera’s Video Analytic function
Please use Internet Explorer as the default browser. If you are using IE 11, please go to
“Setup->Compatibility View Settings” and add the camera’s IP address to the list.
Please follow the step below to enable camera’s video analytics function.
1. Click on “Configurations” on left menu bar
MD-3025-IVS iMotion Detection Setup Guide
4
2. Click on “Video” on the left menu bar and select “enable” Intelligent Video Analytics.
3.3 Setting Resolution and Frame Rate
On the video page, it is important to set the resolution and frame rate correctly.
Please remember to click on “Apply” button after finish settings.
Main Stream
Resolution
Main Stream Frame
Rate
Second Stream Frame
Rate
1920x1080
25FPS
15FPS
!
MD-3025-IVS iMotion Detection Setup Guide
5
3.4 Configure iMotion Detection Function
Please go to “Video Analytics” menu and select “iMotion Detection”
Below is the main page of iMotion Detection.
MD-3025-IVS iMotion Detection Setup Guide
6
The first step is to set the zones according to your environment. The controls are separated
in Zone Area and Zone Settings as indicated above.
Zone Settings
This is the default zone setting. When you click inside the “Zone Area”, you can move
and resize the zone by holding the “inside zone” and the “change points”.
Create another zone: When you press “Add Zone” button, you can create up to 4
zones to fit your need.
.
Zone Area
Zone Settings
Click and hold inside
the zone to move the
block
Click and hold the
change points to resize
the zones.
Click inside the zones to
activate edit mode
Please remember to press “Apply” after change
settings, otherwise the settings won’t take effect.
MD-3025-IVS iMotion Detection Setup Guide
7
After you set the zone area correctly, the next step is to calibrate the object size according
to your installation.
Calibration
“Anything” is our recommendation and you don’t need to do the calibration. However, you
could also choose “People” or “Vehicles” to set “Calibration” when the camera cannot
detect objects accurately.
You can perform calibration by checking the “people” in the calibration field.
On the Zone Area, a window label “Min Size” will appear.
Click on “Min. Size” window to change the size of the minimum object.
Min Size: Object smaller than this size will not be detected.
Click inside the small
box to change the size
Minimum Object Size
1
2
3
4
5
6
Click left mouse button
to set each position
Click right mouse
button to complete a
zone when you finish a
last position setting.
MD-3025-IVS iMotion Detection Setup Guide
8
Other Important Settings
Detect: Please keep on “Anything” for an accurate detection.
Sensitivity: “Moderate” is the recommended settings
Statistic Chart Display: When enabled, it will show the result in a statistic graph. It is not
recommended to turn on this function as it might use a lot of CPU resource which can
influence the performance. If you use this function, please remember to turn it off after
finish using it.
Event Action
The camera’s iMotion Detection function can perform certain action when an event is met.
For example, it can be set if any object is moving into the detection areas, it will start to
record a video and send alarm email to user.
Example:
Setting if the object is moving into the detection areas between 7am to 9pm, the camera will
record an event video and send an email to user.
1. Go to the camera’s UI, select “Event->Media Format”, and choose recording period.
2. Check “Enable SMTP”, select SMTP or Gmail, and fill in all the relation data. (Please
press “Test SMTP” button to make sure your setting is correct or not.)
MD-3025-IVS iMotion Detection Setup Guide
9
3. Go to “Video Analytics” and “iMotion Detection”. You can change the “Interval” to have
the time interval between events.
4. Now, please click on “Set Event Action”. Click on “Add”. Then the following screen will
appear. Please enter the data as shown below. Please remember to click on “Save”
after finish settings.
Note: The Event Name does not allow spaces in between words. Please enter the
event name as one single word.
!
Andere Handbücher für MD-3025-IVS
2
Inhaltsverzeichnis
Andere AirLive Sicherheitskamera Handbücher
AirLive
AirLive MD-3025-IVS Bedienungsanleitung
AirLive
AirLive FE-201DM Bedienungsanleitung
AirLive
AirLive FE-501DM Bedienungsanleitung
AirLive
AirLive AirCam OD-600HD Bedienungsanleitung
AirLive
AirLive SmartCube 300W Einrichtungshandbuch
AirLive
AirLive FE-200VD Bedienungsanleitung
AirLive
AirLive WL-5420CAM Bedienungsanleitung
AirLive
AirLive AirCam OD-600HD Bedienungsanleitung
AirLive
AirLive SmartCube 300W Bedienungsanleitung
AirLive
AirLive BU-3028 Bedienungsanleitung
AirLive
AirLive FE-201DM Bedienungsanleitung
AirLive
AirLive AIRCAM OD-600HD Bedienungsanleitung
AirLive
AirLive CU-720IR Bedienungsanleitung
AirLive
AirLive MD-3025 Bedienungsanleitung
AirLive
AirLive MD-3025 Bedienungsanleitung
AirLive
AirLive POE-200HD Bedienungsanleitung
AirLive
AirLive IP-200PHD-24(B) Bedienungsanleitung
AirLive
AirLive BU-3026 Bedienungsanleitung
AirLive
AirLive OD-2025HD Bedienungsanleitung
AirLive
AirLive BC-5010 Bedienungsanleitung
