AJAX Fire Protect Bedienungsanleitung

Fire Protect User Manual

Fire Protect is a wireless indoor fire detector with an in-built buzzer and a

battery, ensuring up to 4 years of autonomous operation. Fire Protect can

detect smoke and rapid temperature increase.

Connecting to the Ajax security system via a secured Jeweller radio

protocol, Fire Protect (Fire Protect Plus) communicates with the hub at a

distance of up to 1,300 m in line of sight.

The detector can be a part of third-party security systems, connecting to

them via the Ajax uartBridge or Ajax ocBridge Plus integration module.

The detector is set up via the Ajax apps for iOS, Android, macOS, and

Windows. The system notifies the user of all events through push

notifications, SMS, and calls (if activated).

The Ajax security system can be connected to a central monitoring station

of a security company.

Functional Elements

1. Siren hole

2. Light indicator (acts as the sensor and Test button)

3. Smoke chamber hole with the temperature detector behind the net

4. Smart Bracket attachment panel

5. Power button

6. Tamper button

7. QR code

Operating Principle

When smoke penetrates the detector chamber, it distorts infrared light

between the emitter and photoelectric receiver. This distortion triggers a

smoke alarm. When the temperature exceeds 60°С or rises by 30°С during

30 minutes (not necessary to reach 60°С), the detector registers

temperature increase, which triggers a fire alarm.

In case of alarm, the detector activates the built-in buzzer (the siren sound

can be heard from afar) and blinks with the light indicator. When connected

to a security system, both the user and the security company are notified of

the alarm.

The siren can be turned off by pressing the touch button (the center of the

light indicator) or in the Ajax app. If smoke and temperature levels do not

restore to normal values, in 10 minutes, the detector turns on the siren

again.

Connecting the Detector to the Ajax

Security System

Connecting to the hub

Before starting connection:

1. Following the hub user guide, install the Ajax app. Create the account, add

the hub, and create at least one room.

2. Switch on the hub and check the internet connection (via Ethernet cable

and/or GSM network).

3. Make sure that the hub is disarmed and does not update by checking its

status in the Ajax app.

Only users with administrator rights can add the device to the hub

Pairing the detector with hub:

1. Select Add Device in the Ajax app.

2. Name the device, scan or type the QR Code (located on the detector body

and packaging), and select the location room.

3. Tap Add —the countdown will start.

4. Switch on the device.

To make sure that the detector is on, press the on/off button —the logo will

light up red for a second.

For detection and pairing to occur, the detector should be located within the

coverage area of the wireless network of the hub (at a single protected

object). The connection request is transmitted for a short time: at the

moment of switching on the device.

If pairing with the hub fails, the detector operates autonomously; switch off

the detector for 5 seconds and retry.

The detector connected to the hub is displayed in the list of devices in the

app. The update of the detector status in the list depends on the device

inquiry time set in the hub settings (the default value is 36 seconds).

States

1. Devices

2. FireProtect | FireProtect Plus

Parameter

State

Temperature

Temperature of the device. Measures on the device processor

and changes gradually

Jeweller Signal Strength

Signal strength between the hub and the detector

Connection

Connection status between the hub and the device

Battery Charge

Primary battery level of the device

Lid

The tamper state of the device —reacts to the detachment

Routed Through ReX

Displays the status of using the ReX range extender

Smoke

Shows if smoke is detected

Temperature threshold exceeded

The state of temperature threshold exceeded alarm

Rapid temperature rise

The state of rapid temperature increase alarm

High CO Level (Fire Protect

Plus only)

The state of dangerous CO level alarm

Backup Battery Charge

Backup battery level of the device

Smoke sensor

The state of the smoke detector

Smoke sensor dust level

The dust level in the smoke chamber

Firmware

Detector firmware version

Device ID

Device identifier

Setting

1. Devices

2. Fire Protect | Fire Protect Plus

3. Settings

Setting

Value

First field

Device name, can be edited

Room

Selecting the virtual room to which the device is assigned

Dangerous CO Level Alarm

(FireProtect Plus only)

If active, the detector alerts of exceeding the limits of carbon

monoxide concentration

High temperature alarm

If active, the detector reacts when the temperature is 60°C and

higher

Rapid temperature rise alarm

If active, the detector reacts to rapid temperature increase (30°С

for 30 minutes or less)

Alert with a siren if smoke is detected

If active, Home Siren and Street Siren are activated in case of

smoke alarm

Alert with a siren if temperature

threshold exceeded

If active, Home Siren and Street Siren are activated in case if

temperature threshold exceeded

Alert with a siren if rapid temperature

rise detected

If active, Home Siren and Street Siren are activated in case if

rapid temperature rise detected

Alert with a siren if CO detected (Fire

Protect Plus only)

When turned on, Home Siren and Street Siren are activated in

case if CO concentration is dangerous

Jeweller Signal Strength Test

Switches the device to the signal strength test mode

Fire Protect Self-Test

Starts Fire Protect self-test

User Guide

Opens the detector User Guide

Un pair Device

Disconnects the sensor from the hub and deletes its settings

Indication

Event

Indication

Detector switching on

The logo lights up green for 1 second

Detector switching off

The logo blinks red three times and the device switches off

Registration failed

The logo blinks green for a minute, then the device switches to

the autonomous mode

Smoke or temperature increase

detected

The siren switches on, the logo lights red during the fire/smoke

alarm

Battery low

•One short sound signal per 90 sec —main batteries low (CR2)

•Two short sound signals per 90 sec —backup battery low

(CR2032)

•Three short sound signals per 90 sec —both batteries low

Performance testing

The Ajax security system allows conducting tests for checking the

functionality of connected devices.

The tests do not start straight away but within a period of 36 seconds when

using the standard settings. The test time start depends on the settings of

the detector scanning period (the paragraph on “Jeweller” settings in hub

settings).

According to the requirements of EN50131 standard, the level of the radio

signal sent by wireless devices is decreased during the test mode.

Detector Testing

Before installing the detector, check the smoke sensor. To test it, switch on

the detector and press the sensor button (the logo centre) for a few

seconds –the detector will test the smoke chamber with electronic

simulation of smoke generation and then will switch on the siren for 6

seconds.

You will receive the notification in the Ajax app regarding the test result and

detector status.

Installation

Selecting the Location

The location of the detector depends on its remoteness from the hub, and

obstacles hindering the radio signal transmission: walls, floors, large

objects inside the room.

Check the Jeweller signal level at the installation location

If the signal level is low (one bar), we cannot guarantee the stable

operation of the detector. Take all possible measures to improve the quality

of the signal. At least, move the detector: even a 20 cm shift can

significantly improve the quality of signal reception.

If the detector has low or unstable signal strength even after moving, use

a ReX Radio signal range extender.

Install the detector at the ceiling in the highest point where hot air and

smoke are concentrated in case of fire.

If there are any beams at the ceiling, protruding by 30 or more centimetres

from the ceiling level, install the detector between every two beams.

Installation procedure

Before installing the detector, make sure that you have selected the optimal

location that follows the guidelines of this manual!

1. Fix the Smart Bracket panel on the ceiling using bundled screws. If you use

any other attachment tools, make sure that they do not damage or deform

the attachment panel.

Use double-side adhesive tape only for temporary attachment of the detector. The tape runs dry

with time, which can cause falling, false triggering, and detector malfunction.

2. Put the detector on the attachment panel by turning it clockwise on Smart

Bracket. When the detector is fixed in Smart Bracket, it blinks with LED,

signalling that the tamper is closed.

If LED doesn’t blink after fixing in Smart Bracket, check the status of the

tamper in the Ajax app and then the fixing tightness of the panel.

If someone detaches the detector from the surface or takes it off the

attachment panel, the security system notifies you.

Do not install the detector:

1. outside the premises (outdoors);

2. nearby any metal objects or mirrors causing attenuation or screening of the

signal;

3. at any places with fast air circulation (air fans, open windows or doors);

4. closer than a meter to the cooking surface;

5. inside premises with the temperature and humidity beyond the range of

permissible limits;

6. Closer than 1 m to the hub.

Autonomous Use of the Detector

The detector can be used autonomously, without connecting to a security

system.

1. Switch on the detector by pressing the on/off button for 3 seconds (the logo

will light up green for 1 second) and conduct the smoke test.

2. Select the optimal location of the detector following the recommendations

in the second part of the section selecting the location of this manual.

3. Install the detector as described in the section Installation procedure.

Inhaltsverzeichnis

Andere AJAX Sicherheitssensor Handbücher

AJAX

AJAX vhfBridge Bedienungsanleitung

AJAX

AJAX ReX Bedienungsanleitung

AJAX

AJAX MotionProtect Bedienungsanleitung

AJAX

AJAX DoorProtect Plus Jeweller Bedienungsanleitung

AJAX

AJAX FireProtect 2 Bedienungsanleitung

AJAX

AJAX GlassProtect Bedienungsanleitung

AJAX

AJAX GlassProtect Fibra Bedienungsanleitung

AJAX

AJAX FireProtect 2 Jeweller Bedienungsanleitung

AJAX

AJAX LeaksProtect Bedienungsanleitung

AJAX

AJAX MotionProtect Bedienungsanleitung

AJAX

AJAX FireProtect 2 Jeweller Bedienungsanleitung

AJAX

AJAX GlassProtect Bedienungsanleitung

AJAX

AJAX MotionProtect Curtain Bedienungsanleitung

AJAX

AJAX LeaksProtect Bedienungsanleitung

AJAX

AJAX DoorProtect Bedienungsanleitung

AJAX

AJAX LeaksProtect Bedienungsanleitung

AJAX

AJAX FireProtect 2 Jeweller Bedienungsanleitung

AJAX

AJAX MotionProtect Bedienungsanleitung

AJAX

AJAX LeaksProtect Bedienungsanleitung

AJAX

AJAX DoorProtect Plus Bedienungsanleitung

AJAX

AJAX MotionProtect Plus Fibra Bedienungsanleitung

AJAX

AJAX GlassProtect Bedienungsanleitung

AJAX

AJAX MotionCam Fibra Bedienungsanleitung

AJAX

AJAX GlassProtect Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung