AJAX MotionProtect Bedienungsanleitung

MotionProtect / MotionProtect Plus User

Manual

Updated August 13, 2020

MotionProtect is a wireless motion detector designed for indoor use. It can

operate for up to 5 years from an in-built battery, and monitors the area within

12-meter radius. MotionProtect ignores animals, while recognizes a human from

the rst step.

MotionProtect Plus uses radio frequency scanning along with a thermal sensor,

ltering interference from thermal radiation. Can operate up to 5 years from an

in-built battery.

MotionProtect (MotionProtect Plus) operates within the Ajax security system,

connected to the via the protected protocol. The communication

range is up to 1700 (MotionProtect Plus up to 1200) meters in the line of sight.

In addition, the detector can be used as a part of third-party security central

units via the or integration modules.

Buy motion detector with microwave sensor MotionProtect Plus

hub Jeweller

Ajax uartBridge Ajax ocBridge Plus

The detector is set up via the for iOS, Android, macOS and Windows.

The system noties user of all events through push notications, SMS and calls

(if activated).

The Ajax security system is self-sustaining, but the user can connect it to the

central monitoring station of a security company.

Functional Elements

Operating Principle

Ajax app

Buy motion detector MotionProtect

1. LED indicator

2. Motion detector lens

3. SmartBracket attachment panel (perforated part is required for actuating

the tamper in case of any attempt to dismantle the detector)

4. Tamper button

5. Device switch

6. QR code

Thermal PIR sensor of MotionProtect detects intrusion into protected room by

detecting moving objects whose temperature is close to the temperature of the

human body. However, the detector can ignore domestic animals if the suitable

sensitivity has been chosen in the settings.

When the MotionProtect Plus detects motion, it will additionally carry out radio

frequency scanning of the room, preventing false actuation from thermal

interferences: air ows from sun-heated curtains and louvre shutters, operating

thermal air fans, replaces, air conditioning units, etc.

After actuation, the armed detector immediately transmits an alarm signal to the

hub, activating the sirens and notifying the user and security company.

If before arming the system, the detector has detected motion, it will not arm

immediately, but during the next inquiry by the hub.

Connecting the Detector to the Ajax Security System

Connecting the Detector to the hub

Before starting connection:

Only users with administrator rights can add the device to the hub

How to connect the detector to the hub:

1. Following the hub manual recommendations, install the .

Create an account, add the hub to the application, and create at least one

room.

Ajax application

2. Switch on the hub and check the internet connection (via Ethernet and/or

GSM network).

3. Make sure that the hub is disarmed and does not update by checking its

status in the app.

For detection and pairing to occur, the detector should be located within the

coverage of the wireless network of the hub (at a single protected object).

1. Select theAdd Deviceoption in the Ajax application.

2. Name the device, scan/write manually the QR Code (located on the body

and packaging), and select the location room.

3. Select Add — the countdown will begin.

4. Switch on the device.

Request for connection to the hub is transmitted for a short time at the moment

of switching on the device.

If the detector failed to connect to the hub, switch off the detector for 5 seconds

and retry.

The connected detector will appear in the devices list in the application. Update

of the detector statuses in the list depends on the device inquiry time set in the

hub settings(default value is 36 seconds).

Connecting the Detector to Third Party security systems

To connect the detector to a third party security central unit with the

or integration module, follow the recommendations in the

manuals of these devices.

States

Parameter Value

Temperature Temperature of the Detector. Measured on the

processor and changes gradually

Jeweller Signal Strength Signal strength between the hub and the

detector

Connection Connection status between the hub and the

detector

Battery Charge Battery level of the detector, displayed in

increments of 25%

Lid The tamper mode of the detector, which reacts

to the detachment of or damage of the body

Delay when entering, sec Delay time when entering

Delay when leaving, sec Delay time when exiting

Routed through ReX Displays the status of using the ReX range

extender

uartBridge

ocBridge Plus

1. Devices

2. MotionProtect | MotionProtect Plus

Sensitivity Sensitivity level of the motion sensor

Always Active If active, the motion detector is always in the

armed mode

Temporary Deactivation

Shows the status of the device: active,

completely disabled by the user, or only

notications about triggering of the device

tamper button are disabled

Firmware Detector rmware version

Device ID Device identier

Settings

Setting Value

First eld Detector name, can be edited

Room Selecting the virtual room to which the device is

assigned

Delay when entering, sec Selecting delay time when entering

Delay when leaving, sec Selecting delay time on exit

Delays in night mode Delay turned on when using night mode

Arm in night mode If active, the detector will switch to armed mode

when using night mode

Alarm LED indication

Allows you to disable the ashing of the LED

indicator during an alarm. Available for devices

with rmware version 5.55.0.0 or higher

Sensitivity Choosing the sensitivity level of the motion

sensor.

For MotionProtect:

1. Devices

2. MotionProtect | MotionProtect Plus

3. Settings

How to nd the rmware version or

the ID of the detector or device?

For MotionProtect Plus:

Always active If active, the detector always registers motion

Alert with a siren if motion detected If active, and are

activated when the motion detected

Jeweller Signal Strength Test Switches the detector to the signal strength test

mode

Detection Zone Test Switches the detector to the detection area test

Attenuation test

Switches the detector to the signal attenuation

test mode (available in detectors with rmware

version 3.50 and later)

Temporary Deactivation

Allows the user to disconnect the device

without removing it from the system.

Two options are available:

User Guide Opens the User Guide

High — for premises with a minimum amount of

obstacles, motion is detected as quickly as

possible

Medium — for premises with potential

obstacles (windows, air conditioner, heating

element, etc)

Low — ignore pets weighing up to 20 kg and up

to 50 cm tall

High — the detector disregards cats (under 25

cm)

Medium — disregards small dogs (under 35 cm)

Low — disregards animals under 50 cm.

HomeSiren StreetSiren

Deactivate entirely — the device will not

execute system commands or participate in

automation scenarios, and the system will

ignore device alarms and other notications

Deactivate lid notications — the system will

ignore only notications about the triggering of

the device tamper button

Learn more about temporary

deactivation of devices

Unpair device Disconnects the detector from the hub and

deletes its settings

Before using the detector as a part of the security system, set up the suitable

sensitivity level.

Switch the Always Active if the detector is located in a room requiring 24-hour

control. Regardless of whether the system is set in the armed mode, you will

receive notices of any detected motion.

If any motion is detected, the detector activates the LED for 1 second and

transmits an alarm signal to the hub and then to the user and central monitoring

station (if it is connected).

Detector operation indication

Event Indication Note

Turning on the detector Lights up green for about one

second

Detector connection to the

, and Lights up continuously for a

few seconds

Alarm / tamper activation Lights up green for about one

second

Alarm is sent once in 5

seconds

Battery needs replacing During the alarm,slowly lights

up and goes off green

Replacement of the detector

battery is described in the

manual

Detector Testing

The Ajax security system allows conducting tests for checking the functionality

of connected devices.

The tests do not start immediately but within a period of 36 seconds when using

the standard settings. The time of the start depends on the settings of the

detector polling period (the paragraph on Jeweller settings in the hub settings).

hub ocBridge Plus

uartBridge

Battery Replacement

Device installation

Selection of the Detector Location

The controlled area and the eciency of the security system depends on the

location of the detector.

The device developed only for indoor use.

Location of MotionProtect depends on the remoteness from the hub and

presence of any obstacles between the devices hindering the radio signal

transmission: walls, inserted oors, large-size objects located within the room.

Check the signal level at the installation location

Jeweller Signal Strength Test

Detection Zone Test

Attenuation test

If the signal level is at one bar, we cannot guarantee stable operation of the

security system. Take all possible measures to improve the quality of the signal!

As a minimum, move the device – even 20 cm shift can signicantly improve the

quality of reception.

If after moving the device still has a low or unstable signal strength, use the

The direction of the detector lens should be perpendicular to the probable way of

intrusion into the room

Make sure that any furniture, domestic plants, vases, decorative or glass

structures do not block the eld of view of the detector.

We recommend installing the detector at the height of 2,4 meters.

If the detector is not installed at the recommended height, this will reduce the

area of the motion detection zone and impair the operation of the function of

ignoring animals.

Installation of the Detector

ReX

radio signal range extender

Andere Handbücher für MotionProtect

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AJAX Sicherheitssensor Handbücher

AJAX

AJAX FireProtect 2 Jeweller Bedienungsanleitung

AJAX

AJAX MotionProtect Bedienungsanleitung

AJAX

AJAX DoorProtect Bedienungsanleitung

AJAX

AJAX FireProtect 2 (CO) Jeweller Bedienungsanleitung

AJAX

AJAX FireProtect 2 Jeweller Bedienungsanleitung

AJAX

AJAX DoorProtect Bedienungsanleitung

AJAX

AJAX LeaksProtect Bedienungsanleitung

AJAX

AJAX MotionProtect Bedienungsanleitung

AJAX

AJAX DoorProtect Bedienungsanleitung

AJAX

AJAX CombiProtect Fibra Bedienungsanleitung

AJAX

AJAX CombiProtect Bedienungsanleitung

AJAX

AJAX FireProtect 2 Jeweller Bedienungsanleitung

AJAX

AJAX MotionProtect Bedienungsanleitung

AJAX

AJAX FireProtect 2 (Heat) Jeweller Bedienungsanleitung

AJAX

AJAX FireProtect Bedienungsanleitung

AJAX

AJAX FireProtect 2 Jeweller Bedienungsanleitung

AJAX

AJAX vhfBridge Bedienungsanleitung

AJAX

AJAX MotionProtect Plus Bedienungsanleitung

AJAX

AJAX MotionCam Jeweller Bedienungsanleitung

AJAX

AJAX LeaksProtect Bedienungsanleitung

AJAX

AJAX Fire Protect Bedienungsanleitung

AJAX

AJAX MotionProtect Bedienungsanleitung

AJAX

AJAX CombiProtect Bedienungsanleitung

AJAX

AJAX LeaksProtect Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung