AJAX GlassProtect Bedienungsanleitung
GlassProtect User manual
Updated June 8, 2020
GlassProtect is a wireless indoor glass break detector recognizing the sound of
shattering the glass at a distance of up to 9 meters. GlassProtect can operate
up to 7 years from a pre-installed battery and has a socket for connecting a
third-party wired detector.
GlassProtect connects to the Ajax security system via the protected
radio protocol. The communication range is up to 1,000 meters in line of sight.
Also, GlassProtect can be connected to third-party security systems using the
or integration modules.
Users can congure GlassProtect via the for macOS, Windows, iOS, or
Android. The system noties users of all events through push notications, SMS,
and calls (if activated).
The user can connect the Ajax security system to the central monitoring station
of a security company.
Jeweller
Ajax uartBridge Ajax ocBridge Plus
Ajax app
Buy breakage detector GlassProtect
Functional elements
Operating Principle
GlassProtect uses a sensitive electret microphone to detect the sound of glass
breaking, consisting of a low-frequency hit sound and high-frequency crashing
sound of glass shatters. Such two-stage glass break detection decreases the
risk of false triggering.
GlassProtect detector does not react to the breaking of the lm-covered glass:
shockproof, sunscreen, decorative, or any other type of lm. To detect the breaking of
1. LED indicator
2. Microphone hole
3. SmartBracket attachment panel (perforated part is required for actuating
the tamper in case of any attempt to dismantle the detector. Don’t break it
out!)
4. External detector connection socket
5. QR code
6. Device switch
7. Tamper button
such kind of glass, we recommend using the wireless opening detector
with shock and tilt sensors.
If triggered, GlassProtect immediately transmits the alarm signal to the ,
activating the (if connected) and notifying the user and security company.
Connecting
Detector Connection to hub
Before starting connection:
Only users with administrator rights can add the device to the hub.
Pairing the detector with hub:
DoorProtect Plus
hub
sirens
1. Following the hub user guide, install the . Create the account, add
the hub, and create at least one room.
Ajax app
2. Switch on the hub and check the internet connection (via Ethernet cable
and/or GSM network).
3. Make sure that the hub is disarmed and does not update by checking its
status in the Ajax app.
1. Select Add Device in the Ajax app.
2. Name the device, scan or type the QR code (located on the detector body
and packaging), and select the location room.
For detection and pairing to occur, the detector should be located within the
coverage area of the wireless network of the hub (at a single protected object).
The connection request is transmitted for a short time: at the moment of
switching on the device.
If the device failed to pair (LED blinks once per second), switch it off for 5
seconds and retry. The detector connected to the hub appears in the list of
devices in the app. The update of the detector statuses in the list depends on
the device ping interval set in the hub settings (the default value is 36 seconds).
3. Tap Add — the countdown will start.
4. Switch on the device.
Parameter Value
Temperature Temperature of the detector, measured on the
processor and changes gradually
Jeweller Signal Strength Signal strength between the hub and the
detector
Connection Connection status between the hub and the
detector
Battery Charge Battery level of the detector, displayed in
increments of 25%
Lid The tamper state, which reacts to the
detachment of or damage to the detector body
Delay when entering, sec Delay time when entering. The option is
available only with a connected wired detector.
Delay when leaving, sec Delay time when exiting. The option is available
only with a connected wired detector.
Sensitivity Sensitivity level of the sensor
Secondary detector Status of the external detector connection to
GlassProtect
Routed Through ReX Displays the status of using the radio signal
range extender ReX
Always Active Indicates whether the detector is always armed
Firmware Detector rmware version
Device ID Device identier
Settings
Setting Value
First eld Detector name, can be edited
Room Selecting the virtual room to which the device is
assigned
1. Devices
2. GlassProtect
3. Settings
Delay when entering, sec
Selecting delay time when entering. The option
is available only with a connected wired
detector.
Delay when leaving, sec Selecting delay time on exit. The option is
available only with a connected wired detector.
Delays in night mode Delay turned on when using night mode
Arm in night mode If active, the detector will switch to armed mode
when using night mode
Sensitivity
Choosing the sensitivity level of glass break
detector:
External contact enabled If active, the detector registers external detector
alarms
Always active If active, the detector always registers glass
breakage
Alert with a siren if glass break detected If active, and are
activated when the glass break detected
Activate the siren if an additional contact is
open
If active, HomeSiren and StreetSiren are
activated in case of an external detector alarm
Jeweller Signal Strength Test Switches the detector to the Jeweller signal
strength test mode
Detection Zone Test Switches the detector to the detection area test
Attenuation Test
Switches the detector to the signal fade test
mode (available in detectors with rmware
version 3.50 and later)
User Guide Opens the User Guide for detector
Unpair Device Disconnects the detector from the hub and
deletes its settings
Indication
Event Indication Note
High
Normal
Low
HomeSiren StreetSiren
Turning on the detector Lights up green for about one
second
Detector connection to the
, and Lights up continuously for a
few seconds
Alarm / tamper activation Lights up green for about one
second
Alarm is sent once in 5
seconds
Battery needs replacing
During the alarm, it slowly
lights up green and slowly
goes out
Replacement of the detector
battery is described in the
manual
Functionality testing
The Ajax security system allows conducting tests for checking the functionality
of connected devices.
The tests do not start immediately but within a period of 36 seconds when using
standard settings. The test time start depends on the settings of the detector
scanning period (the paragraph on “Jeweller” settings in hub settings).
Detector functionality testing
Having dened the location of the detector and having xed the device with the
bundled adhesive tape, test the detection zone.
GlassProtect does not react to clapping!
Testing the detector
hub ocBridge Plus
uartBridge
Battery Replacement
Jeweller Signal Strength Test
Detection Zone Test
Attenuation Test
Hit the glass with your st without breaking it. If the detector catches a low-
frequency sound, the LED blinks. Simulate a high-frequency glass shattering
sound for 1.5 seconds after the rst hit with a special tool or hitting a glass with
a metal object. After recognizing the sound, the detector switches off the LED
indicator for a second.
To be triggered when the system is armed, the detector needs to recognize sounds in the
following order: low-frequency sound (hit) rstly, then high-frequency sound (glass
shattering, shards). Otherwise, the alarm will not go off.
Switch on/off all the appliances that usually operate in the room: generators, air
conditioners, etc. If this triggers the detector, try to change the sensitivity or
relocate GlassProtect.
Use the sensitivity level, at which the detector correctly passes both test stages
and does not respond to any devices operating in the room.
Installing the device
Selecting the Location
In some cases, the household activity can cause false alarms
The location of GlassProtect depends on its remoteness from the hub, and
obstacles hindering the radio signal transmission: walls, oors, large objects
inside the room.
Check the Jeweller signal level at the installation location
If the signal level is low (one bar), we cannot guarantee the stable operation of
the detector. Take all possible measures to improve the quality of the signal. At
Andere Handbücher für GlassProtect
8
Inhaltsverzeichnis
Andere AJAX Sicherheitssensor Handbücher
AJAX
AJAX GlassProtect Bedienungsanleitung
AJAX
AJAX CombiProtect Bedienungsanleitung
AJAX
AJAX LeaksProtect Bedienungsanleitung
AJAX
AJAX MotionProtect Bedienungsanleitung
AJAX
AJAX MotionProtect Bedienungsanleitung
AJAX
AJAX LifeQuality Jeweller Bedienungsanleitung
AJAX
AJAX GlassProtect Bedienungsanleitung
AJAX
AJAX FireProtect 2 Jeweller Bedienungsanleitung
AJAX
AJAX Fire Protect Bedienungsanleitung
AJAX
AJAX FireProtect Bedienungsanleitung
AJAX
AJAX FireProtect 2 Heat/CO Jeweller Bedienungsanleitung
AJAX
AJAX MotionProtect Curtain Bedienungsanleitung
AJAX
AJAX GlassProtect Bedienungsanleitung
AJAX
AJAX MotionProtect Bedienungsanleitung
AJAX
AJAX GlassProtect Fibra Bedienungsanleitung
AJAX
AJAX ReX Bedienungsanleitung
AJAX
AJAX MotionCam Bedienungsanleitung
AJAX
AJAX FireProtect Bedienungsanleitung
AJAX
AJAX MotionProtect Bedienungsanleitung
AJAX
AJAX DoorProtect Plus Bedienungsanleitung
