AL Tech DSD 4121RV Bedienungsanleitung
D
S
D
4
1
2
1
R
V
B
a
s
i
c
V
i
e
w
e
r
'
s
G
u
i
d
e
2／28 DSD 4121 RV
Important Safety Information ........................................................................................................................ 4
Front and Back Panels .................................................................................................................................
Install & Connect the DSD 4121 RV Decoder .............................................................................................. 6
The Remote Control .....................................................................................................................................
DSD 4121 RV Decoder : Features and menu............................................................................................... 13
Legal Matters .............................................................................................................................................. 24
Help and Information .................................................................................................................................. 26
BASIC VIEWER’S GUIDE
TABLE OF CONTENTS
The DSD 4121 RV Basic Viewer’s Guide is the subject of intellectual
property rights, including copyright, under domestic law and
international conventions. All rights are reserved.
The 4121 Basic Viewer’s Guide supplements the information supplied
with the packaging of the decoder as well as the detailed information
available on our website.
Due to software upgrades, the features and functionalities in this
Basic Viewer’s Guide may differ from those on your decoder. Please
visit for the latest Viewer’s Guide.
www.uec.com.au
!
RV
!
Please Note : The Network Operator requires the use of a
10.7 GHz ( 10700 ) LNB to receive all available TV services.
D
S
D
4
1
2
1
R
V
B
a
s
i
c
V
i
e
w
e
r
'
s
G
u
i
d
e
5
12
DSD 4121 RV 3／28
This DSD 4121 RV Decoder meets International Safety Standards. Please read the following recommended safety
precautions carefully.
Keep liquids away from the decoder and do not put anything on top of the decoder which may spill (example : lit
candles or containers of liquid). Do not use the decoder in extreme temperature and humid conditions.
Before cleaning the decoder, first disconnect the decoder from the mains. Use a dry cloth to clean the exterior.
Do not block the ventilation holes and ensure that free airflow is maintained around the decoder.
Never stand the decoder on soft furnishings or on carpet.
Do not use or store the decoder near a heater or where it is exposed to direct sunlight.
Never stack other electronic equipment on top of, or below the decoder.
Do not attempt to repair the decoder yourself. You should also never remove the cover of the decoder. Any
tampering with the decoder will invalidate the warranty. Refer all servicing to Altech UEC Australia,
Tel. +61 2 94255777.
If the decoder is installed in an area subject to intense lightning activity, protection devices for the decoder mains
connector are recommended.
The earth/grounding system must comply with local regulations.
MAINS SUPPLY
LIQUIDS AND SPILLAGE
CLEANING
VENTILATION
SERVICING
LIGHTNING
EARTHING
IMPORTANT SAFETY INFORMATION
!
4121
RV
The powerpack supplied with this decoder. It operates within the range 100-250 V AC 47-63 Hz mains supply only.
Connect the power cable to the decoder before connecting the other end to the power outlet. Disconnect the decoder
from the power outlet before connecting or disconnecting the decoder from any other equipment. A well regulated
12V D.C supply is essential for this unit to operate efficiently, visit www.uec.com.au for a list of recommended D.C
regulators.
D
S
D
4
1
2
1
R
V
B
a
s
i
c
V
i
e
w
e
r
'
s
G
u
i
d
e
4／28 DSD 4121 RV
Smartcard Slot Behind the Front Panel Cover.
10
RESET Reboots the decoder, i.e. if decoder freezes etc.
8
Front Panel
LED Display
Displays the time (Standby Mode) or displays the selected
TV channel.
9
LEDs
Bi-colour
RED/GREEN
AMBER
GREEN
Indicates response to remote control commands and/or error mode
RED = Decoder in standby mode or an error condition has occurred.
GREEN = Normal operations.
Flashes = when there are incoming messages
Flashes = when RCU command received.
1
Connect to the LNB on dish
Power Input connector
Connect to your home AC mains outlet
11
Data Services
Connects to RS232 (for software upgrade)
10
HDMI
Connects to the high definition (HDMI) input on TV or AV home theatre system
9
Composite Video
Connects to the video inputs on TV
8
Video =YPbPr
Connects to the YPbPr inputs on TV
7
Audio = Left & Right
Connects to the analog inputs on TV
6
USB
Connects to USB device (for software upgrade)
5
Connects to Ethernet (currently disabled in this version)
4
Connects to the Digital Audio coaxial input on TV or AV Home Theater System
3
OPTICAL (Optical connector)
Connects to the Digital Audio optical input on TV or AV Home Theater System
2
BACK PANEL
FRONT PANEL
STANDBY Button
1Switches the decoder between ON and STANDBY modes.
MENU Opens command menu for changing the setup.
7
OK Accepts the selection.
6
Increases the volume level.
4VOL
Changes to the previous available channel.
2CH
Decreases the volume level.
5VOL
Changes to the next available channel.
3CH
!
COAXIAL (Coaxial connector)
ETHERNET
Connect to another receiver
12
D
S
D
4
1
2
1
R
V
B
a
s
i
c
V
i
e
w
e
r
'
s
G
u
i
d
e
DSD 4121 RV 5／28
LNB IN
LNB OUT
QUICK START GUIDE FOR EXISTING AURORA INSTALLATIONS
Remove decoder from packaging.
Insert supplied batteries into the remote control.
Connect to existing TV and dish installation - verify the LNB setup in the menus and adjust and re-scan if
necessary.
Decoder should lock to service and present video.
QUICK START GUIDE FOR NEW INSTALLATIONS
Ensure that all connections are secure before connecting the power cable (#11)to the power input connector.
Option A: AV Connectors (Standard Definition TV)
Connect the satellite feed to the SAT IN input (#1) on the decoder.
Connect the Audio / Video cables to the audio (#6) and video (#8) outputs on the decoder and then to
the audio and video inputs on the TV or home theater system.
Option B: HDMI Connector (High Definition TV)
Connect the satellite feed to the SAT IN input (#1) on the decoder.
Connect a High Definition cable to the HDMI connector (#9), and then connect the other end of the
cable to the HDMI connector on the TV.
Option C: HDMI Connector (AV Home Theater system and a High Definition TV)
Connect the satellite feed to the SAT IN input (#1) on the decoder.
Connect a High Definition cable to the HDMI connector (#9), and then connect the other end of the
cable to the HDMI input connector of the AV home theater system. Then connect the output HDMI of
the AV home theater system to the TV.
1
2
INSTALL & CONNECT THE DSD 4121 RV DECODER
CONNECTING THE DSD 4121 RV DECODER
!
!
4121
D
S
D
4
1
2
1
R
V
B
a
s
i
c
V
i
e
w
e
r
'
s
G
u
i
d
e
6／28 DSD 4121 RV
Dish Alignment
If you get the following screen is being displayed on startup then the unit isn’t receiving signal;
This is either because the dish isn’t aligned properly and signal is weak, or the LNB on the DISH is a
frequency other than 10.7GHz.
In order to configure your alignment, or change LNB settings, just press ‘HELP’ button on the remote and
the following screen will appear;
D
S
D
4
1
2
1
R
V
B
a
s
i
c
V
i
e
w
e
r
'
s
G
u
i
d
e
DSD 4121 RV 7／28
Select your approximate location, press ‘OK’ on the remote and the following screen will appear
showing you the co-ordinates to align to;
(Note: compass bearing is aligned to true north)
Press ‘OK’ on the remote once more to change the LNB setting and the following screen will appear;
Now Press the number on the remote which corresponds to your LNB frequency (usually #1) and press
‘OK’.
D
S
D
4
1
2
1
R
V
B
a
s
i
c
V
i
e
w
e
r
'
s
G
u
i
d
e
8／28 DSD 4121 RV
The following screen displaying a satellite finder will then appear;
You can now align your dish, once the bar turns green press ‘OK’ on the remote. If the bar is yellow or
red then you will need to fine tune your alignment.
The following screen will then appear;
If ‘Signal Found’ is displayed at the top of the screen then the unit will begin to scan in services and
channel 800 will appear.
The smart card can then be registered and activated at http://myswitch.digitalready.gov.au/. For any
issues with activation call VAST on; PH:1300 99 3376.
D
S
D
4
1
2
1
R
V
B
a
s
i
c
V
i
e
w
e
r
'
s
G
u
i
d
e
DSD 4121 RV 9／28
CHANGING THE LNB SETTING
Press the MENU button to launch the menu, then.
Navigate to the following menu screens:
Advanced Options
Installation setup
Enter the setup pin (The default is 1234)
LNB setup
Select the LNB type by pressing OK to select first item and using left and right to scroll. Press OK again
to deselect the option.
Enter in the correct LNB value by pressing OK on the LNB Frequency option and then enter the new
LNB value, then press OK again to deselect the option.
Press OK on the “Accept these settings” button.
You will be returned to the Satellite installation menu.
Press OK on “Satellite Rescan” to rescan the decoder with the new LNB settings.
D
S
D
4
1
2
1
R
V
B
a
s
i
c
V
i
e
w
e
r
'
s
G
u
i
d
e
!
!
4121
10／28 DSD 4121 RV
Andere Handbücher für DSD 4121RV
1
Inhaltsverzeichnis
