Allen-Bradley 2711R-APK10 Bedienungsanleitung

Installation Instructions

Adapter Plate Kit

for PanelView 800, 7-inch and 10-inch Terminals

Catalog Numbers 2711R-APK7, 2711R-APK10

About This Publication

This document provides instructions on how to mount a PanelView 800 terminal using an adapter plate into

an existing cutout. The PanelView 800 7-inch terminal mounts to the 2711R-APK7 cutout adapter and the

10-inch terminal mounts to the 2711R-APK10 cutout adapter.

Topic Page

About This Publication 1

Package Contents 3

Tools Required 3

Disconnect the Terminal 3

Attach the Adapter Plate to the Panel 4

Attach the Terminal to the Adapter Plate 5

2Adapter Plate Kit for PanelView 800, 7-inch and 10-inch Terminals

Publication 2711R-IN002A-EN-P - March 2015

Important User Information

Solid-state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State

Controls (Publication SGI-1.1 available from your local Rockwell Automation sales office or online

at http://www.rockwellautomation.com/literature/) describes some important differences

between solid-state equipment and hard-wired electromechanical devices. Because of this

difference, and also because of the wide variety of uses for solid-state equipment, all persons

responsible for applying this equipment must satisfy themselves that each intended application of

this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential

damages resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because

of the many variables and requirements associated with any particular installation, Rockwell

Automation, Inc. cannot assume responsibility or liability for actual use based on the examples

and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information,

circuits, equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of

Rockwell Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety

considerations.

WARNING: Identifies information about practices or circumstances that can cause an

explosion in a hazardous environment, which may lead to personal injury or death,

property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to

personal injury or death, property damage, or economic loss. Attentions help you identify

a hazard, avoid a hazard and recognize the consequences.

SHOCK HAZARD: Labels may be on or inside the equipment (for example,

drive or motor) to alert people that dangerous voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment (for example, drive

or motor) to alert people that surfaces may reach dangerous temperatures.

IMPORTANT Identifies information that is critical for successful application and understanding of the

product.

Adapter Plate Kit for PanelView 800, 7-inch and 10-inch Terminals 3

Publication 2711R-IN002A-EN-P - March 2015

Package Contents

The Cutout Adapter Kit includes:

• A cutout adapter plate with waterproof gasket

• #8-32 nuts with lock washers (6 sets)

• Thin mounting levers (8)

Tools Required

The following tools are required for installation:

• Socket driver with 11/32-inch socket

• Torque wrench capable of 1.36 Nm (12 in-lb) torque

Disconnect the Terminal

1. Disconnect power at the source and remove the power cord from the PanelView terminal.

2. Disconnect all communication cables from the terminal.

Remove the Existing Terminal

1. Remove the self-locking levers that secure the terminal to the panel.

2. Slide the existing terminal out from the panel.

IMPORTANT

Thin mounting levers are only included with 2711R-APK7 and are for use with 2711R-T7T.

There are no mounting levers included with 2711R-APK10. Use the regular mounting levers

that come with 2711R-T10T.

ATTENTION: Make sure the power cord and all communication cables have been

disconnected from the PanelView terminal.

Regular mounting leverThin mounting lever

4Adapter Plate Kit for PanelView 800, 7-inch and 10-inch Terminals

Publication 2711R-IN002A-EN-P - March 2015

Attach the Adapter Plate to the Panel

1. Align the studs on the cutout adapter plate with the existing stud holes on the front of the panel.

2. Place the adapter plate into the front of the panel cutout until the sealing gasket material is firmly

pressed against the front of the panel.

3. Using the supplied nuts with lock washers, fasten the cutout plate onto the studs until the sealing

gasket is slightly compressed against the front of the panel.

4. Using the torque wrench, tighten the nuts to not more than 1.36 Nm (12 in-lb) to maintain a

NEMA Type 4X, 12, or 13 rating. Do not overtighten.

Rear of panel or enclosure

Front of panel or enclosure

Nut

M3.5 H3.0

Screw

M3.5 L15 with Nyseal (waterproof)

Front of adapter plate

with waterproof gasket

Adapter Plate Kit for PanelView 800, 7-inch and 10-inch Terminals 5

Publication 2711R-IN002A-EN-P - March 2015

Attach the Terminal to the Adapter Plate

1. Insert the new terminal into the front of the enclosure until the terminal gasket is flush with the

adapter plate.

Rear of panel or enclosure

Nut

M3.5 H3.0

Rear of PanelView 800 terminal

(7-inch terminal shown)

Mounting levers

6Adapter Plate Kit for PanelView 800, 7-inch and 10-inch Terminals

Publication 2711R-IN002A-EN-P - March 2015

2. Insert all mounting levers into the mounting slots of the terminal.

Slide each lever until the flat side of the lever touches the surface of the panel.

3. When all levers are in place, slide each lever an additional notch or two until you hear a click.

4. Rotate each lever in the direction indicated until lever is in the final latch position. Follow the

latching sequence below to obtain the optimum terminal fit.

IMPORTANT

Use thin mounting levers only when using the 2711R-T7T terminal with the adapter plate.

Short, flat side of mounting lever

Mounting levers

Mounting slots

Rotate until notch in lever aligns with

proper alignment mark on terminal. Notch

Six alignment marks

Latching sequence for 2711R-T7T Latching sequence for 2711R-T10T

Adapter Plate Kit for PanelView 800, 7-inch and 10-inch Terminals 7

Publication 2711R-IN002A-EN-P - March 2015

5. Use this table as a guide to insure an adequate gasket seal between the terminal and the panel.

Terminal Markings for

Alignment

Lever

Position Panel Thickness Range Typical

Gauge

1 1.52…2.01 mm (0.060…0.079 in.) 16

2 2.03…2.64 mm (0.08…0.104 in.) 14

3 2.67…3.15 mm (0.105…0.124 in.) 12

4 3.17…3.66 mm (0.125…0.144 in.) 10

5 3.68…4.16 mm (0.145…0.164 in.) 8/9

6 4.19…4.75 mm (0.165…0.187 in.) 7

ATTENTION: Follow the instructions above to obtain a proper seal and to prevent potential

damage to the terminal. Rockwell Automation assumes no responsibility for water or

chemical damage to the terminal or other equipment within the enclosure because of

improper installation.

44881

Rockwell Automation Support

Rockwell Automation provides technical information on the Web to assist you in using its products.

At http://www.rockwellautomation.com/support/, you can find technical manuals, a knowledge

base of FAQs, technical and application notes, sample code and links to software service packs, and

a MySupport feature that you can customize to make the best use of these tools.

For an additional level of technical phone support for installation, configuration and troubleshooting,

we offer TechConnect support programs. For more information, contact your local distributor or

Rockwell Automation representative, or visit http://www.rockwellautomation.com/support/.

Installation Assistance

If you experience a problem within the first 24 hours of installation, please review the information

that's contained in this manual. You can also contact a special Customer Support number for initial

help in getting your product up and running.

New Product Satisfaction Return

Rockwell Automation tests all of its products to ensure that they are fully operational when shipped

from the manufacturing facility. However, if your product is not functioning and needs to be returned,

follow these procedures.

Documentation Feedback

Your comments will help us serve your documentation needs better. If you have any suggestions on

how to improve this document, complete this form, publication RA-DU002, available at

http://www.rockwellautomation.com/literature/.

Rockwell Automation maintains current product environmental information on its website at

http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.

United States or Canada 1.440.646.3434

Outside United States or Canada Use the Worldwide Locator at

http://www.rockwellautomation.com/support/americas/phone_en.html, or

contact your local Rockwell Automation representative.

United States Contact your distributor. You must provide a Customer Support case number (call the phone

number above to obtain one) to your distributor to complete the return process.

Outside United States Please contact your local Rockwell Automation representative for the return procedure.

Samara

tel. +7 846 273 95 85

[email protected]

Yekaterinburg

tel. +7 343 287 19 19

yekat[email protected]

St. Petersburg

tel. +7 812 327 3752

[email protected]

Moscow

tel. +7 495 641 1616

[email protected]

Helsinki

tel. +358 9 540 4940

info@klinkmann.fi

Vilnius

tel. +370 5 215 1646

[email protected]

Riga

tel. +371 6738 1617

[email protected]

Мinsk

tel. +375 17 200 0876

[email protected]

Tallinn

tel. +372 668 4500

[email protected]

Кiev

tel. +38 044 495 33 40

[email protected].ua

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Allen-Bradley Adapter Handbücher

Allen-Bradley

Allen-Bradley PowerFlex RS-485 DF1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1738 ArmorPOINT Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-ADN Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 20-comm-c FRN 1. Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 20-COMM-D Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet 1786-RPA/B Bedienungsanleitung

Allen-Bradley

Allen-Bradley 20-COMM-M Modbus/TCP Adapter Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 525 Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX 5000 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1734 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet Ex 1797-ACNR15 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2071-TBMF Bedienungsanleitung

Allen-Bradley

Allen-Bradley 140MG Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O PROFIBUS 1794-APBDPV1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet 1786-BNC2TNC Bedienungsanleitung

Allen-Bradley

Allen-Bradley 5069-AENTR Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-AENT Bedienungsanleitung

Allen-Bradley

Allen-Bradley 140G Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2100-ENET Bedienungsanleitung

Allen-Bradley

Allen-Bradley 140G Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1734-AENTRK Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 20-COMM-P Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1734-AENTR Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2100-ENET Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

RCA

RCA AH57R Bedienungsanleitung