Allen-Bradley 2711P-RDT12H Bedienungsanleitung

Installation Instructions

Original Instructions

High-bright Display Modules

Catalog Number

2711P-RDT12H

Topic Page

Important User Information 2

Summary of Changes 3

About the Module 3

Environment and Enclosure 4

Outdoor Installation 4

Hazardous Locations 5

Environnements dangereux 6

Wiring and Safety Guidelines 8

About the Terminals 9

Install the Terminal 9

Logic Module Compatibility 13

External Power Supply For Nonisolated DC Terminals 13

External Power for Isolated DC Terminals 14

Remove and Install the Power Terminal Block 15

DC Power Connections 16

Ethernet Cable 17

Troubleshooting 18

Specifications 20

Additional Resources 22

2Rockwell Automation Publication 2711P-IN026H-EN-P - May 2018

High-bright Display Modules

Important User Information

Read this document and the documents listed in the additional resources section about installation, configuration, and operation of

this equipment before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with

installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.

Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be

carried out by suitably trained personnel in accordance with applicable code of practice.

If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or

application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and

requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual

use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software

described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is

prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

Labels may also be on or inside the equipment to provide specific precautions.

WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous

environment, which may lead to personal injury or death, property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death,

property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the

consequence.

IMPORTANTIdentifies information that is critical for successful application and understanding of the product.

SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that

dangerous voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that

surfaces may reach dangerous temperatures.

ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert

people to potential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective

Equipment (PPE). Follow ALL Regulatory requirements for safe work practices and for Personal Protective

Equipment (PPE).

Rockwell Automation Publication 2711P-IN026H-EN-P - May 2018 3

High-bright Display Modules

Summary of Changes

This document contains new and updated information as indicated in the following table.

About the Module

This document provides instructions on how to install the PanelView™ Plus, PanelView Plus CE,

and PanelView Plus 6 high-bright display module in a panel or enclosure.

Refer to the installation instructions shipped with the logic module and communication module

for field installation of these components.

For complete information on installing , wiring , and troubleshooting the terminals, refer to the

publications listed under Additional Resources.

Topic Page

Updated the Attention note in the section titled External Power Supply for Nonisolated DC Terminals. 13

Removed outdated error messages from the Troubleshooting section and added references to appropriate user

manuals. 18

4Rockwell Automation Publication 2711P-IN026H-EN-P - May 2018

High-bright Display Modules

Environment and Enclosure

See the Outdoor Installation section for additional enclosure and certification information on

the high-bright display modules.

Outdoor Installation

When using the high-bright display module, catalog number 2711P-RDT12H, outdoors,

considerations in maximizing the field life of the front bezel and display are the following:

• Selecting the proper enclosure

• Orientation of the terminal

Both ultraviolet and infrared radiation can reduce the field life of any electronic device. While

the materials used in the terminal bezels provide long field life, that life can be improved by

proper installation.

Ultraviolet (UV) radiation from the sun causes all plastics to fade or yellow and become brittle

over time. Using an antiglare overlay, catalog number 2711P-RGT12, will protect the front of

the terminal from direct exposure to UV radiation and greatly increase its field life.

When installing the high-bright display module in an environment where the front of the

terminal will be in direct sunlight during the hottest part of the day and the external ambient

temperature can exceed 40 °C (104 °F), use the visor kit, catalog number 2711P-RVT12. The

visor reduces the solar load on the front of the display and helps to maintain internal

temperatures within specification.

ATTENTION: This equipment is intended for use in a Pollution Degree 2 industrial environment, in

overvoltage Category II applications (as defined in IEC publication 60664-1), at altitudes up to

2000 m (6561 ft) without derating.

This equipment is considered Group 1, Class A industrial equipment according to IEC/CISPR

Publication 11. Without appropriate precautions, there may be potential difficulties ensuring

electromagnetic compatibility in other environments due to conducted as well as radiated

disturbance.

This equipment is supplied as open-type equipment. It must be mounted within an enclosure that

is suitably designed for those specific environmental conditions that will be present and

appropriately designed to prevent personal injury resulting from accessibility to live parts. The

interior of the enclosure must be accessible only by the use of a tool. The terminals meet specified

NEMA Type and IEC ratings only when mounted in as panel or enclosure with the equivalent rating.

Subsequent sections of this publication may contain additional information regarding specific

enclosure type ratings that are required to comply with certain product safety certifications.

In addition to this publication, see:

• Industrial Automation Wiring and Grounding Guidelines, for additional installation

requirements, Allen-Bradley publication 1770-4.1.

• NEMA Standards publication 250 and IEC publication 60529, as applicable, for explanations of

the degrees of protection provided by different types of enclosure.

Rockwell Automation Publication 2711P-IN026H-EN-P - May 2018 5

High-bright Display Modules

The high-bright display module has a built-in temperature sensor that automatically reduces the

backlight intensity if the temperature inside the cabinet exceeds 55 °C (131 °F). This reduces the

risk of damage to the display.

The paint color, size, and power dissipated by the internal components of an enclosure affect the

temperature rise inside the cabinet. Hoffman, a Rockwell Automation Encompass Partner, has

information to assist you with enclosure selection and heating/cooling accessories to meet the

temperature requirements of the installed equipment. See website

http://www.hoffmanonline.com.

Stirring fans or active cooling may be required in high altitude and high ambient temperature

locations to keep the internal enclosure temperature below 55 °C (131 °F). Use a heater in

installations where the ambient temperature is below 0 °C (32 °F).

The backlight of the high-bright display generates a significant amount of heat when set to full

intensity. To minimize the amount of heat generated and extend the life of the backlight,

decrease the display intensity by using the screen saver with a 5…10 minute delay.

Avoid placing the terminal on the south (north in the southern hemisphere) or west side of the

cabinet, if possible. This will reduce the heat rise due to solar loading during the hottest part of

the day.

Mount the terminal vertically to minimize solar loading on the display. Do not mount the

terminal in a sloped enclosure if it will be exposed to direct sunlight.

Hazardous Locations

This equipment is suitable for these locations:

• Class I, Division 2 Groups A, B, C, D

• Class II, Division 2 Groups F, G

• Class III

• Ordinary, nonhazardous locations only

The following statement applies to use in hazardous locations.

The PanelView Plus, PanelView Plus CE, or PanelView Plus 6 terminals have a temperature code

of T4 when operating in a 55 °C (131 °F) maximum ambient temperature. Do not install the

WARNING: Explosion Hazard

• Substitution of components may impair suitability for hazardous locations.

• Do not disconnect equipment unless power has been switched off and area is known to be

nonhazardous.

• Do not connect or disconnect components unless power has been switched off.

• All wiring must comply with N.E.C. articles 501, 502, 503, and/or C.E.C. section 18-1J2 as

appropriate.

• Peripheral equipment must be suitable for the location in which it is used.

6Rockwell Automation Publication 2711P-IN026H-EN-P - May 2018

High-bright Display Modules

terminals in environments where atmospheric gases have ignition temperatures less than 135 °C

(275 °F).

Environnements dangereux

Cet équipement ne peut être utilisé que dans les environnements suivants :

• Classe I, Division 2, Groupes A, B, C, D

•ClasseII,Division2,GroupesF,G

• Classe III

• ou environnements non-dangereux

La mise en garde suivante s'applique à une utilisation en environnement dangereux.

Le code de température de fonctionnement des terminaux PanelView Plus, PanelView Plus CE,

ou PanelView Plus 6 est T4 pour une température ambiante maximale de 55 °C (131 °F).

N'installez pas les terminaux dans des environnements contenant des gaz atmosphériques

inflammables à moins de 135 °C (275 °F).

USB Ports

The terminals contain universal serial bus (USB) ports that comply with hazardous location

environments. This section details the field-wiring compliance requirements and is provided in

accordance with the National Electrical Code, article 500.

WARNING: DANGER D'EXPLOSION

• La substitution de composants peut rendre cet équipement impropre à une utilisation en

environnement dangereux.

• Ne pas déconnecter l'équipement sans s'être assuré que l'alimentation est coupée ou que

l'environnement est classé non dangereux.

• Ne pas connecter ou déconnecter des composants sans s'être assuré que l'alimentation est

coupée.

• L'ensemble du câblage doit être conforme, selon le cas, aux articles 501-4(b), 502-4(b) et 503-

3(b) du Code national de l'électricité des Etats-Unis.

• L'équipement périphérique doit être adapté à l'environnement dans lequel il est utilisé.

Rockwell Automation Publication 2711P-IN026H-EN-P - May 2018 7

High-bright Display Modules

PanelView Plus 700 to 1500 Terminals Control Drawing

Selected nonincendive field wiring apparatus must have nonincendive circuit parameters

conforming with Table 2.

Application Information

Per the National Electrical Code the circuit parameters of nonincendive field wiring apparatus

for use in hazardous locations shall be coordinated with the associated nonincendive field wiring

apparatus such that their combination remains nonincendive. The PanelView Plus 700 to 1500

and the USB peripheral device shall be treated in this manner.

The circuit parameters of the PanelView Plus 700 to 1500 USB port are given in Table 1. The

USB peripheral device and its associated cabling shall have circuit parameters with the limits

given in Table 2 for them to remain nonincendive when used with the PanelView Plus 700 to

1500 USB port. If cable capacitance and inductance are not known the following values from

ANSI/ISA-RP 12.06.01-2003 may be used:

Ccable = 60 pF/ft

Lcable = 0.20 μH/ft

Nonincendive field wiring must be wired and separated in accordance with 501.10(B)(3) of the

National Electrical Code (NEC) ANSI/NFPA 70 or other local codes as applicable.

This associated nonincendive field wiring apparatus has not been evaluated for use in

combination with another associated nonincendive field wiring apparatus.

Table 1 - PanelView Plus 700 to 1500 USB Port Circuit Parameters

Voc Isc

CaLa

Groups A and B Groups C and D Groups A and B Groups C and D

5.25V DC 1.68 A 10 μF 10 μF 15 μH 15 μH

Table 2 - Required Circuit Parameters for the USB Peripheral Device

Vmax ≥V

Imax ≥I

Ci + Ccable ≤C

Li+ Lcable ≤L

Associated Nonincendive Field Wiring Apparatus

PanelView Plus 700 to 1500 Host Product

Nonincendive Field

Wiring Apparatus

Nonincendive Field Wiring

USB Port

USB

Peripheral

Device

8Rockwell Automation Publication 2711P-IN026H-EN-P - May 2018

High-bright Display Modules

Symbol Definitions

Wiring and Safety Guidelines

Use publication NFPA 70E, Electrical Safety Requirements for Employee Workplaces, IEC

60364 Electrical Installations in Buildings, or other applicable wiring safety requirements for the

country of installation when wiring the devices. In addition to the NFPA guidelines:

• connect the device and other similar electronic equipment to its own branch circuit.

• protect the input power by a fuse or circuit breaker rated at no more than 15 A.

• route incoming power to the device by a separate path from the communication lines.

• cross power and communication lines at right angles if they must cross.

• Communication lines can be installed in the same conduit as low level DC I/O lines

(less than 10V).

• shield and ground cables appropriately to avoid electromagnetic interference (EMI).

• Grounding minimizes noise from EMI and is a safety measure in electrical installations.

For more information on grounding recommendations, refer to the National Electrical Code

published by the National Fire Protection Association.

For more information, refer to Wiring and Grounding Guidelines for PanelView Plus Devices

Technical Data, publication 2711P-TD001. You can locate this publication in the literature

library at this website a http://www.rockwellautomation.com/literature/.

Voc Open circuit voltage of the host USB port.

Isc Maximum output current of the host USB port.

Vmax

Maximum applied voltage rating of the USB peripheral device.

Vmax shall be greater than or equal to Voc in Table 1 (Vmax ≥ Voc ).

Imax

Maximum current to which the USB peripheral device can be subjected.

Imax shall be greater than or equal to Isc in Table 1 (Imax ≥ Isc).

CiMaximum internal capacitance of the USB peripheral device.

CaMaximum allowed capacitance of the USB peripheral device and its associated cable. The sum of Ci of the USB

peripheral device and Ccable of the associated cable shall be less than or equal to Ca(Ci + Ccable ≤ Ca).

LiMaximum internal inductance of the USB peripheral device.

LaMaximum allowed inductance of the USB peripheral device and its associated cable. The sum of Liof the USB

peripheral device and Lcable of the associated cable shall be less than or equal to La(Li+ Lcable ≤ La).

Rockwell Automation Publication 2711P-IN026H-EN-P - May 2018 9

High-bright Display Modules

About the Terminals

High-bright display modules are available only as separate components. Logic modules and

communication modules must be ordered separately.

Attach the logic module and communication module to the display module before panel

installation. See the instructions shipped with each module.

Parts List

These items are shipped with the terminals:

• Power terminal block

• Mounting clips

• FactoryTalk View software preloaded

• Installation instructions and panel cutout template

Required Tools

These tools are required for installation:

• Panel cutout tools

• Small, slotted screwdriver

• Torque wrench (lb•in)

Install the Terminal

Before installing the terminal in a panel, review these topics:

• Mounting clearances

• Panel cutout dimensions

• Product dimensions

Logic Module

Display Module

Power Input, DC

Ethernet Port

Serial Port

USB Ports

10 Rockwell Automation Publication 2711P-IN026H-EN-P - May 2018

High-bright Display Modules

Mounting Clearances

Allow adequate clearance around the terminal, inside the enclosure, for adequate ventilation.

Consider heat produced by other devices in the enclosure. The ambient temperature around the

terminals must be between 0…55 °C (32…131 °F).

These minimum clearances are required for ventilation:

• Top clearance: 51 mm (2 in.)

• Bottom clearance: 102 mm (4 in.)

• Side clearances: 25 mm (1 in.)

• Back clearance: 25 mm (1 in.)

Minimum side clearance for insertion of memory card is 102 mm (4 in.).

Panel Cutout Dimensions

Use the full size template shipped with your terminal to mark the cutout dimensions.

The 1250 Touch PanelView Plus, PanelView Plus CE, and PanelView Plus 6 Terminals are 257

mm (10.11 in.) high and 338 mm (13.29 in.) wide.

Mount the Terminal in a Panel

Four mounting clips secure the terminal to the panel.

Follow these steps to mount the terminal in a panel.

1. Cut an opening in the panel by using the panel cutout shipped with the terminal.

ATTENTION: Disconnect all electrical power from the panel before making the panel cutout.

Make sure the area around the panel cutout is clear.

Take precautions so metal cuttings do not enter any components already installed in the panel.

Failure to follow these instructions may result in personal injury or damage to panel components.

Inhaltsverzeichnis

Andere Allen-Bradley Steuereinheit Handbücher

Allen-Bradley

Allen-Bradley ArmorBlock MaXum B Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-ADN Bedienungsanleitung

Allen-Bradley

Allen-Bradley ProcessLogix R300.1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O 1794-IV32 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756-M02AS Bedienungsanleitung

Allen-Bradley

Allen-Bradley Compact 5000 Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-OB2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-ENET/B Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1200 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix SynchLink 1756-SYNCH Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1200 Bedienungsanleitung

Allen-Bradley

Allen-Bradley C Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerMonitor 500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-KA2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock 1732E Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-DH485 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Rockwell Automation 1734-4IOL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1492-CM1771-LD007 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 750 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-HYD02 Bedienungsanleitung

Allen-Bradley

Allen-Bradley C Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley DH485/RS-232C Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2711P-RN6K Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix DeviceNet Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung