Allen-Bradley ControlLogix 1756-DH485 Bedienungsanleitung

ControlLogix

DH-485

Communication

Module

1756-DH485

User Manual

Important User Information

Solid state equipment has operational characteristics differing from those of

electromechanical equipment. Safety Guidelines for the Application, Installation and

Maintenance of Solid State Controls (publication SGI-1.1 available from your local

Rockwell Automation sales office or online at

http://literature.rockwellautomation.com) describes some important differences

between solid state equipment and hard-wired electromechanical devices. Because of

this difference, and also because of the wide variety of uses for solid state equipment,

all persons responsible for applying this equipment must satisfy themselves that each

intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or

consequential damages resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes.

Because of the many variables and requirements associated with any particular

installation, Rockwell Automation, Inc. cannot assume responsibility or liability for

actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of

information, circuits, equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written

permission of Rockwell Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety

considerations.

The first line of trademarks is an example; the brand or product name changes according to publication but the rest of the line should remain the

same. The second line should be used exactly as listed below in any case where it applies.

Allen-Bradley, ControlLogix, and RSLinx are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

WARNING Identifiesinformationaboutpracticesorcircumstancesthatcancause

an explosion in a hazardous environment, which may lead to personal

injury or death, property damage, or economic loss.

IMPORTANT Identifies information that is critical for successful application and

understanding of the product.

ATTENTION Identifies information about practices or circumstances that can lead

to personal injury or death, property damage, or economic loss.

Attentions help you identify a hazard, avoid a hazard, and recognize

the consequence

SHOCK HAZARD

Labelsmaybelocatedonorinsidetheequipment,forexample,adrive

or motor, to alert people that dangerous voltage may be present.

BURN HAZARD Labelsmaybelocatedonorinsidetheequipment,forexample,adrive

or motor, to alert people that surfaces may be dangerous

temperatures.

iPublication 1756-UM532A-EN-P - May 2006

Table of Contents

Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Preface

Purpose of This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preface-i

Who Should Use This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . Preface-i

Other Resources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preface-i

Chapter 1

1756-DH485 Module Overview

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

What the Module Does . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Module Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Module Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Prevent Electrostatic Discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Removal and Insertion Under Power . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Typical Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Remote Messaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Remote Upload and Download . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Routing Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

DH-485 and CIP Messaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

Alphanumeric Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

Chapter 2

Overview of the DH-485 Network

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

DH-485 Network Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

DH-485 Network Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

DH-485 Token Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

DH-485 Network Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Devices that Use the DH-485 Network . . . . . . . . . . . . . . . . . . . . . . . 2-3

1747-AIC Isolated Link Coupler for DH-485 . . . . . . . . . . . . . . . . . . 2-4

1761-NET-AIC Advanced Interface Converter Product Overview . 2-6

Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Device Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Node Address Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Misconception about the 1761-NET-AIC Converter . . . . . . . . . . . . 2-7

1747-UIC USB to DH-485 Interface Converter . . . . . . . . . . . . . . . . 2-7

Example System Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

Configure the SLC 5/03, SLC 5/04, and SLC 5/05 Controller

Channel 0 for DH-485. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Important Planning Considerations . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

Hardware Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

Software Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13

Publication 1756-UM532A-EN-P - May 2006

Table of Contents ii

Chapter 3

Use Data Highway 485 Network

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

What Is Data Highway 485? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Link Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Two Methods of Communication Over a DH-485 Network . . . . . . 3-2

Use DH-485 Messaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Local DH-485 Messaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Limitations of Local DH-485 Messaging . . . . . . . . . . . . . . . . . . . 3-5

Remote DH-485 Messaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Configuration Information in DH-485 Messaging. . . . . . . . . . . . . . 3-11

Application Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

Example DH-485 Network Routing Configuration. . . . . . . . . . . . . 3-13

Use the Common Industrial Protocol (CIP) Messaging. . . . . . . . . . 3-14

Chapter 4

Use RSLinx Software to Create a

Routing Table

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Choose the Correct Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Use RSLinx Software to Create a Routing Table . . . . . . . . . . . . . . . . 4-2

What Is a Routing Table? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

ControlLogix Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Create the Routing Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Set the Controller Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Chapter 5

Communicate from an SLC 5/03

Controller to a Logix Controller

over a DH-485 Network

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Hardware Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Use the Controller Slot to Route the Local Message . . . . . . . . . . . . . 5-3

Create a Local Message in RSLogix 500 . . . . . . . . . . . . . . . . . . . . . . . 5-4

Configure the Message. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

Create a Logic Map for the Local Message in

RSLogix 5000 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Publication 1756-UM532A-EN-P - May 2006

Table of Contents iii

Chapter 6

Communicate Between SLC

Controllers over DH+ and DH485

Networks

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

SLC 5/04 Controller Sends a Remote Message . . . . . . . . . . . . . . . . . 6-2

Hardware Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

Create the Routing Table in RSLinx Software . . . . . . . . . . . . . . . 6-3

Configure the SLC 5/03 Controller Channel 1 Link ID . . . . . . . 6-4

Configure the SLC 5/04 Channel 1 Link ID . . . . . . . . . . . . . . . . 6-5

Create a Message in RSLogix 500 . . . . . . . . . . . . . . . . . . . . . . . . . 6-6

Configure the Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7

SLC 5/03 Controller Sends a Remote Message . . . . . . . . . . . . . . . . . 6-8

Hardware Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8

Create the Routing Table in RSLinx Software . . . . . . . . . . . . . . . 6-9

Create a Remote Message in RSLogix 500 . . . . . . . . . . . . . . . . . 6-10

Configure the Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11

Chapter 7

Communicate Between a PLC-5

Controller and a Remote SLC 5/03

Controller over Multiple DH-485

Networks

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

Hardware Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2

Create the Routing Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3

Configure the PLC-5 DH+ Channel 1A Link ID . . . . . . . . . . . . 7-4

Create a Message in RSLogix 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4

Configure the Message. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5

Chapter 8

Communicate from an SLC 5/05

Controller to an SLC 5/03

Controller over an EtherNet/IP

Network

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

Hardware Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2

Create a Message in RSLogix 500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

Configure the Message. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4

Review the Multihop Feature in RSLogix 500 . . . . . . . . . . . . . . . . . . 8-5

Chapter 9

Communicate to a SLC 5/03

Controller on a DH-485 Network

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

Hardware Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2

Create a Message in RSLogix 5000 . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3

Configure the Message. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4

Publication 1756-UM532A-EN-P - May 2006

Table of Contents iv

Chapter 10

Communicate from a Logix

Controller to an SLC 5/03

Controller over EtherNet/IP and

DH-485 Networks

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

Hardware Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2

Create a Remote 1756-ENBT Message in RSLogix 5000 . . . . . . . . 10-3

Configure the Message. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4

Appendix A

Specifications Appendix B

Troubleshoot the 1756-DH485

Module

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Check Power Supply and Module Status . . . . . . . . . . . . . . . . . . . . . . B-1

Interpret the LED Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . B-2

Interpret the Alphanumeric Indicators . . . . . . . . . . . . . . . . . . . . . . . . B-3

Interpret the OK

Status Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4

Routing Errors in DH-485 Messaging . . . . . . . . . . . . . . . . . . . . . . . . B-4

Routing Errors in Local DH-485 Messaging . . . . . . . . . . . . . . . . B-4

Routing Errors in Remote DH-485 Messaging . . . . . . . . . . . . . . B-5

Index

Rockwell Automation Support . . . . . . . . . . . . . . . . . . . . . . . . Backcover

Installation Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . Backcover

New Product Satisfaction Return . . . . . . . . . . . . . . . . . . . Backcover

iPublication 1756-UM532A-EN-P - May 2006

Preface

Purpose of This Manual

This manual describes how to understand, configure, and troubleshoot your

ControlLogix Data Highway 485 communication interface module.

This manual also provides step-by-step procedures on how to use the

1756-DH485 module to send DH-485 messages between ControlLogix, PLC,

and SLC controllers in DH-485 applications.

Who Should Use This

Manual

Use this manual if you program applications that use 1756-DH485 modules.

We assume you have a good understanding of the Data Highway 485 protocol.

This user manual contains a brief description of the Data Highway 485

network in Chapter 2, Overview of the DH-485 Network.

Other Resources

Refer to the manuals listed in the table Devices that Use the DH-485 Network

on page 2-3.

Publication 1756-UM532A-EN-P - May 2006

Preface ii

Notes:

1Publication 1756-UM532A-EN-P - May 2006

Chapter

1756-DH485 Module Overview

Introduction

This chapter describes the 1756-DH485 module, and what you must know and

do before you begin to use it.

What the Module Does

The 1756-DH485 module supports the following types of communication:

•Data Highway 485 (DH-485) Messaging

•Connectivity to two separate DH-485 networks in one module

•Common Industrial Protocol (CIP) Messaging

Module Requirements

The following are required for using the 1756-DH485 communication

module:

•RSLinx Software, version 2.41 or later

•Node address within the range of 0-31

•AIC+ link coupler (1761-NET-AIC) communications adapter

•Compatible with SLC 5/03 controllers or later

For See

What the Module Does 1-1

Module Requirements 1-1

Module Features 1-2

Prevent Electrostatic Discharge 1-3

Removal and Insertion Under Power 1-4

Typical Applications 1-5

Remote Messaging 1-7

Routing Limitations 1-8

Publication 1756-UM532A-EN-P - May 2006

1-2 1756-DH485 Module Overview

Module Features

The 1756-DH-485 module offers the following features:

•Sends messages between devices on DH-485 networks and devices on

other networks such as ControlNet, EtherNet/IP, or other DH-485

networks

•Bridges support to other NetLinx networks via the CLX gateway

•Configure channels and ports using RSLinx Classic software, version

2.43 or later

•Accesses other networks by using a routing table editor that lets

DH-485 devices use the 1756-DH485 module and ControlLogix chassis

•Supports all benefits and attributes of a ControlLogix communication

module

•Supports firmware upgrades

•Removal and insertion under power (RIUP), can be removed and

inserted under power without disrupting power to other modules in the

chassis

•4-character display

•Default Controller Slot feature for local messaging

•Serial Port Configuration

•No limit on number of modules per chassis, up to the number of

available slots and the capabilities of the power supply

This figure shows the external features of the 1756-DH485 module.

TIP Download firmware upgrades via the backplane. Do

not use DH485 network for downloads.

WARNING

When you insert or remove the module while backplane

power is on, an electrical arc can occur. This could cause an

explosion in hazardous location installations.

Be sure that power is removed or the area is nonhazardous

before proceeding. Repeated electrical arcing causes

excessive wear to contacts on both the module and its

mating connector. Worn contacts may create electrical

resistance that can affect module operation.

Inhaltsverzeichnis

Andere Allen-Bradley Steuereinheit Handbücher

Allen-Bradley

Allen-Bradley FLEX I/O 1794-IP4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-OG Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix DeviceNet 1756-DNB Merkblatt

Allen-Bradley

Allen-Bradley 2711P-RDT12H Bedienungsanleitung

Allen-Bradley

Allen-Bradley 160-RS1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1492-AIFM16-F-5 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-OBN Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX Ex 1797-OB4D Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock MaXum B Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O 1794-OB8EP Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1757-ABRIO Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1200 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1770-KFDG Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1769-ASCII Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1747-SN Bedienungsanleitung

Allen-Bradley

Allen-Bradley Series B Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1746-HSCE Bedienungsanleitung

Allen-Bradley

Allen-Bradley OptiSIS 1711-P05SISID050S Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1734-IB8S Bedienungsanleitung

Allen-Bradley

Allen-Bradley C Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1492-CM1771-LD008F Bedienungsanleitung

Allen-Bradley

Allen-Bradley DF1 Montageanleitung

Allen-Bradley

Allen-Bradley ControlNet-to-FOUNDATION Fieldbus H1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 DeviceNet Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung