Allen-Bradley ArmorBlock 1732E-OB16M12R Bedienungsanleitung

Installation Instructions

ArmorBlock 2-Port EtherNet/IP Module

Catalog Numbers 1732E-IB16M12R, 1732E-OB16M12R,

1732E-IB16M12DR, 1732E-OB16M12DR, 1732E-16CFGM12R,

1732E-IB16M12SOEDR, 1732E-8X8M12DR

Table of Contents

Topic Page

Important User Information 2

Environment and Enclosure 3

Preventing Electrostatic Discharge 3

Overview 4

Catalog Number Explanation 6

Install the Module 6

Set the Network Address 6

Mount the Module 7

Product Dimensions 8

Connect the I/O, Network and Auxiliary Cables to the Module 9

Configure the Module 12

Interpret LED Indicators 13

Specifications 15

2ArmorBlock 2-Port EtherNet/IP Module

Publication 1732E-IN004C-EN-E - May 2012

Important User Information

Solid-state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls

(Publication SGI-1.1 available from your local Rockwell Automation sales office or online at

http://www.rockwellautomation.com/literature/) describes some important differences between

solid-state equipment and hard-wired electromechanical devices. Because of this difference, and also

because of the wide variety of uses for solid-state equipment, all persons responsible for applying this

equipment must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular installation, Rockwell Automation, Inc.

cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING: Identifies information about practices or circumstances that can cause an

explosion in a hazardous environment, which may lead to personal injury or death,

property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to

personal injury or death, property damage, or economic loss. Attentions help you

identify a hazard, avoid a hazard and recognize the consequences.

SHOCK HAZARD: Labels may be on or inside the equipment (for example, drive or

motor) to alert people that dangerous voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment (for example, drive or

motor) to alert people that surfaces may reach dangerous temperatures.

IMPORTANT Identifies information that is critical for successful application and understanding of the

product.

ArmorBlock 2-Port EtherNet/IP Module 3

Publication 1732E-IN004C-EN-E - May 2012

Environment and Enclosure

Preventing Electrostatic Discharge

ATTENTION: This equipment is intended for use in a Pollution Degree 2

industrial environment, in overvoltage Category II applications (as defined in

IEC 60664-1), at altitudes up to 2000 m (6562 ft) without derating.

This equipment is considered Group 1, Class A industrial equipment according

to IEC/CISPR 11. Without appropriate precautions, there may be difficulties

with electromagnetic compatibility in residential and other environments due to

conducted and radiated disturbances.

This equipment is supplied as open-type equipment. It must be mounted within

an enclosure that is suitably designed for those specific environmental

conditions that will be present and appropriately designed to prevent personal

injury resulting from accessibility to live parts. The enclosure must have

suitable flame-retardant properties to prevent or minimize the spread of flame,

complying with a flame spread rating of 5VA, V2, V1, V0 (or equivalent) if

nonmetallic. The interior of the enclosure must be accessible only by the use of

a tool. Subsequent sections of this publication may contain additional

information regarding specific enclosure type ratings that are required to

comply with certain product safety certifications.

In addition to this publication, see:

• Industrial Automation Wiring and Grounding Guidelines, Rockwell

Automation publication 1770-4.1, for additional installation requirements.

• NEMA Standard 250 and IEC 60529, as applicable, for explanations of the

degrees of protection provided by different types of enclosure.

ATTENTION: This equipment is sensitive to electrostatic discharge, which can

cause internal damage and affect normal operation. Follow these guidelines

when you handle this equipment:

• Touch a grounded object to discharge potential static.

• Wear an approved grounding wriststrap.

• Do not touch connectors or pins on component boards.

• Do not touch circuit components inside the equipment.

• Use a static-safe workstation, if available.

• Store the equipment in appropriate static-safe packaging when not in use.

4ArmorBlock 2-Port EtherNet/IP Module

Publication 1732E-IN004C-EN-E - May 2012

Additional Resources

If you would like a manual, you can:

• download a free electronic version from the internet:

http://www.rockwellautomation.com/literature/

• purchase a printed manual by contacting your local Allen-Bradley distributor or

Rockwell Automation representative

Overview

The EtherNet/IP ArmorBlock is a 24V DC I/O module that communicates via

EtherNet/IP. The sealed IP65, IP67 and IP69K housing of these modules requires no

enclosure. Note that environmental requirements other than IP65, IP67 and IP69K may

require an additional appropriate enclosure. I/O connectors are sealed M12 style.

EtherNet/IP networks use advanced network technology, for example,

producer/consumer communication, to increase network functionality and throughput.

Resource Description

Pinout Guide for 1732 ArmorBlock 2 Port

Ethernet Block, publication 1732E-WD001

Detailed description of how to wire your module.

1732E EtherNet/IP ArmorBlock supporting

Sequence of Events,

publication 1732E-UM002

Detailed description of how to install, configure and use

your 1732E-IB16M12SOEDR module.

Integrated Architecture and CIP Sync

Configuration, publication IA-AT003

Detailed explanation on how to set up and use

ArmorBlock modules in a CIP Sync application.

Industrial Automation Wiring and Grounding

Guidelines, publication 1770-4.1

More information on proper wiring and grounding

techniques.

ArmorBlock 2-Port EtherNet/IP Module 5

Publication 1732E-IN004C-EN-E - May 2012

Module Identification

(1) Protective Earth is provided for the grounding of field devices and is internally connected to each Pin 5 of the M12 I/O

connectors. See I/O Connectors on page 9.

(2) Functional Earth grounds the I/O block’s EtherNet/IP communication circuitry which is designed to mitigate the effect of

noise on the network. See EtherNet/IP Connector on page 10.

44945

LINK 1 LINK 2

Status LEDs

Auxiliary power

Functional Earth(1)

Node address

switches

Protective Earth(2)

EtherNet/IP D-Code

M12 connector

EtherNet/IP D-Code

M12 connector

M12 I/O connectors M12 I/O connectors

6ArmorBlock 2-Port EtherNet/IP Module

Publication 1732E-IN004C-EN-E - May 2012

Catalog Number Explanation

Refer to the table for a description of the module catalog numbers.

Install the Module

To install the module:

• Set the network address

•Mountthemodule

• Connect the I/O, Network and Auxiliary cables to the module.

Set the Network Address

The I/O block ships with the rotary switches set to 999 and DHCP enabled.

To change the network address, you can do one of the following:

• adjust the switch on the front of the module.

• use a Dynamic Host Configuration Protocol (DHCP) server, such as Rockwell

Automation BootP/DHCP.

• retrieve the IP address from nonvolatile memory.

The I/O block reads the switches first to determine if the switches are set to a valid

number. To set the network address:

1. Rotate the three (3) switches on the front of the module using a small

blade screwdriver.

Catalog Number Description Network

Connector

Auxiliary

Power

1732E-IB16M12R 16 Channel 24V DC Digital Input Dual-Port

EtherNet Module

Dual D-code

M12

Single

4-pin mini

1732E-OB16M12R 16 Channel 24V DC Digital Output Dual-Port

EtherNet Module

1732E-16CFGM12R 16 Channel 24V DC Configurable Digital I/O

Dual-Port EtherNet Module

1732E-IB16M12DR Diagnostic 16 Channel 24V DC Digital Input

Dual-Port EtherNet Module

732E-OB16M12DR Diagnostic 16 Channel 24V DC Digital Output

Dual-Port EtherNet Module

1732E-8X8M12DR Diagnostic 8-Input/8-Output 24V DC Digital I/O

Dual-Port EtherNet Module

1732E-IB16M12SOEDR Diagnostic Sequence of Events 16 Channel 24V

DC Digital Input Dual-Port EtherNet Module

ArmorBlock 2-Port EtherNet/IP Module 7

Publication 1732E-IN004C-EN-E - May 2012

2. Line up the small notch on the switch with the number setting you wish to use.

Valid settings range from 001…254.

3. Cycle power.

Set Network Address

When the switches are set to a valid number, the I/O block’s IP address is 192.168.1.xxx

(where xxx represents the number set on the switches). The I/O block’s subnet mask is

255.255.255.0 and the gateway address is set to 0.0.0.0. When the I/O block uses the

network address set on the switches, the I/O block does not have a host name assigned to it

or use any Domain Name Server.

If the switches are set to an invalid number (for example, 000 or a value greater than 254

excluding 888), the I/O block checks to see if DHCP is enabled. If DHCP is enabled, the

I/O block asks for an address from a DHCP server. The DHCP server also assigns other

Transport Control Protocol (TCP) parameters.

If DHCP is not enabled, the I/O block uses the IP address (along with other TCP

configurable parameters) stored in nonvolatile memory.

Mount the Module

Two sets of mounting holes are used to mount the module directly to a panel or machine.

Mounting holes accommodate #8 (M4) pan head screws. The torque specification is

1.13 Nm (10 in-lb).

Example shows default

node address set at 163.

44233

8ArmorBlock 2-Port EtherNet/IP Module

Publication 1732E-IN004C-EN-E - May 2012

Product Dimensions

Refer to the mounting dimensions illustration to help you mount the module.

Module Dimensions

Mount the Module in High Vibration Areas

If you mount the module in an area that is subject to shock or vibration, we recommend

you use a flat and a lock washer to mount the module. Mount the flat and the lock washer

as shown in the mounting illustration. Torque the mounting screws to 1.13 Nm (10 in-lb).

LINK 1 LINK 2

44946

43.25 mm

(1.70 in.)

26.5 mm

(1.04 in.)

65 mm

(2.56 in.)

179 mm

(7.05 in.) 169 mm

(6.65 in.)

Front view Side view

ArmorBlock 2-Port EtherNet/IP Module 9

Publication 1732E-IN004C-EN-E - May 2012

High Vibration Area Mounting

Connect the I/O, Network and Auxiliary Cables to the Module

The ArmorBlock EtherNet/IP family has 5-pin micro-style connectors. We provide caps

to cover the unused connectors on your module. Connect the quick-disconnect cord sets

you selected for your module to the appropriate ports.

I/O Connectors

Refer to the pinout diagrams for the I/O connectors

Micro-style 5-Pin Input Female Connector

Micro-style 5-Pin Output Female Connector

44766

Lock washer

Flat washer

1 2

44807

(View into connector)

Pin 1 Sensor source voltage

Pin 2 Input B

Pin 3 Return

Pin 4 Input A

Pin 5 PE

1 2

(View into connector)

Pin 1 Not used

Pin 2 Output B

Pin 3 Return

Pin 4 Output A

Pin 5 PE

44807

10 ArmorBlock 2-Port EtherNet/IP Module

Publication 1732E-IN004C-EN-E - May 2012

Self-configuring Connector

I/O Self-configure Circuitry

EtherNet/IP Connector

D-Code Micro Network Female Connector

ATTENTION: Make sure all connectors and caps are securely tightened to

properly seal the connections against leaks and maintain IP enclosure and

NEMA type requirements.

1 2

(View into connector)

Pin 1 Sensor source voltage

Pin 2 Input or output B

Pin 3 Return

Pin 4 Input or output A

Pin 5 PE

44807

Output scan list

Turn output on Output

circuit

Sensor or

actuator

Connector pin

Input is on

(or output is on)

Input

circuit

43601

Input scan list

From PLC

To PLC

(View into connector)

Pin 1 M12_Tx+

Pin 2 M12_Rx+

Pin 3 M12_Tx-

Pin 4 M12_Rx-

Pin 5 Connector shell shield FE

44808

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Allen-Bradley Steuereinheit Handbücher

Allen-Bradley

Allen-Bradley ArmorBlock Series Handbuch

Allen-Bradley

Allen-Bradley PowerMonitor 500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-PLS Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-QRD Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1757-ABRIO Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-OFE Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O 1794-OB8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock 1732D A Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley CAB6-HA 3 Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1500 1764-MM1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O 1794-IV32 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-12X4M12QCDR Handbuch

Allen-Bradley

Allen-Bradley ControlLogix 1756-HYD02 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1746-HSCE Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-8IOLM12R Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-OA8K Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1762-IF4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1203 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley Kinetix 5700 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-KT/B Installations- und Benutzerhandbuch

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-IT4IM12R Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O 1794-IP4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley DH485/RS-232C Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung