Allen-Bradley ArmorBlock A Series Bedienungsanleitung

Installation Instructions

ArmorBlock 16-Point EtherNet/IP Module,

Series A

Catalog Numbers 1732E-IB16M12, 1732E-OB16M12,

1732E-16CFGM12, 1732E-16CFGM12W, 1732E-IB16M12W

Topic Page

Important User Information 2

Environment and Enclosure 3

Prevent Electrostatic Discharge 3

About the EtherNet/IP ArmorBlock 16-Point I/O Modules 4

Catalog Number Explanation 6

Install the Module 6

Set the Network Address 6

Mount the Module 7

Product Dimensions 8

Connect the I/O, Network and Auxiliary Cables to the ArmorBlock Module 9

Specifications 19

2ArmorBlock 16-Point EtherNet/IP Module, Series A

Publication 1732E-IN002B-EN-E - February 2011

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls

(publication SGI-1.1 available from your local Rockwell Automation sales office or online at

http://literature.rockwellautomation.com) describes some important differences between solid state

equipment and hard-wired electromechanical devices. Because of this difference, and also because of

the wide variety of uses for solid state equipment, all persons responsible for applying this equipment

must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular installation, Rockwell Automation, Inc.

cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING

Identifies information about practices or circumstances that can cause an

explosion in a hazardous environment, which may lead to personal injury or death,

property damage, or economic loss.

IMPORTANT

Identifies information that is critical for successful application and understanding

of the product.

ATTENTION

Identifies information about practices or circumstances that can lead to personal

injury or death, property damage, or economic loss. Attentions help you to identify

a hazard, avoid a hazard, and recognize the consequences.

SHOCK HAZARD

Labels may be on or inside the equipment, for example, a drive or motor, to alert

people that dangerous voltage may be present.

BURN HAZARD

Labels may be on or inside the equipment, for example, a drive or motor, to alert

people that surfaces may reach dangerous temperatures.

ArmorBlock 16-Point EtherNet/IP Module, Series A 3

Publication 1732E-IN002B-EN-E - February 2011

Environment and Enclosure

Follow these guidelines for environment and enclosure information for this

equipment.

Prevent Electrostatic Discharge

Follow these guidelines when you handle this equipment.

ATTENTION

This equipment is intended for use in overvoltage Category II applications (as

defined in IEC 60664-1), at altitudes up to 2000 m (6562 ft) without derating.

This equipment is considered Group 1, Class A industrial equipment according

to IEC/CISPR 11. Without appropriate precautions, there may be difficulties

with electromagnetic compatibility in residential and other environments due

to conducted and radiated disturbances.

This equipment is supplied as enclosed equipment. It should not require

additional system enclosure when used in locations consistent with the

enclosure type ratings stated in the Specifications section of this publication.

Subsequent sections of this publication may contain additional information

regarding specific enclosure type ratings, beyond what this product provides,

that are required to comply with certain product safety certifications.

In addition to this publication, see:

• Industrial Automation Wiring and Grounding Guidelines, Rockwell

Automation publication, 1770-4.1, for additional installation

requirements.

• NEMA Standard 250 and IEC 60529, as applicable, for explanations of

the degrees of protection provided by different types of enclosure.

ATTENTION

This equipment is sensitive to electrostatic discharge that can cause internal

damage and affect normal operation. Follow these guidelines when you

handle this equipment.

• Touch a grounded object to discharge potential static.

• Wear an approved grounding wrist strap.

• Do not touch connectors or pins on component boards.

• Do not touch circuit components inside the equipment.

• Use a static-safe workstation if available.

• Store the equipment in appropriate static-safe packaging when not in

use.

4ArmorBlock 16-Point EtherNet/IP Module, Series A

Publication 1732E-IN002B-EN-E - February 2011

About the EtherNet/IP ArmorBlock 16-Point I/O

Modules

The EtherNet/IP 1732E ArmorBlock is a 24V DC I/O module that

communicates via EtherNet/IP. The sealed IP65, IP67 and IP69K housing of

these modules requires no enclosure. Note that environmental requirements

other than IP65, IP67 and IP69K may require an additional appropriate

enclosure. I/O connectors are sealed M12 style.

EtherNet/IP network uses advanced network technolgy, for example,

producer/consumer communication, to increase network functionality and

throughput. Visit our web site at www.ab.com/networks for

producer/consumer technology information and updates.

ArmorBlock 16-Point EtherNet/IP Module, Series A 5

Publication 1732E-IN002B-EN-E - February 2011

EtherNet/IP ArmorBlock 16-Point I/O Module

(1) Functional Earth grounds the I/O block’s EtherNet/IP communication circuitry which is designed to

mitigate the effect of noise on the network. See 10 for network connections.

(2) Protective Earth is provided for the grounding of field devices and is internally connected to each Pin 5 of

the M12 I/O connectors. See 11 for I/O connections.

LINK

NET

MOD

EtherNet/IP

X10

X100 X1

44231

EtherNet/IP

D-CodeM12

Connector

44232

Status

LEDs

I/O

Connectors

Auxiliary

Power

Functional

Earth(1)

Metal

Housing

Plastic

Housing

Node

Address

Switches

Protective

Earth(2)

Protective

Earth(2)

EtherNet/IP

D-CodeM12

Connector

I/O

Connectors

I/O

Connectors

Node

Address

Switches

6ArmorBlock 16-Point EtherNet/IP Module, Series A

Publication 1732E-IN002B-EN-E - February 2011

Catalog Number Explanation

Refer to the table for a description of the catalog numbers.

Install the Module

Refer to the following sections to install your module.

•Set the Network Address

•Mount the Module

•Connect the I/O, Network and Auxiliary Cables to the ArmorBlock

Module

Set the Network Address

The I/O block ships with the rotary switches set to 999 and DHCP-enabled.

To change the network address, you can do one of the following:

•adjust the switches on the front of the module.

•use a Dynamic Host Configuration Protocol (DHCP) server, such as

Rockwell Automation BootP/DHCP.

•retrieve the IP address from nonvolatile memory.

The I/O block reads the switches first to determine if the switches are set to a

valid number. Set the network address by adjusting the 3 switches on the front

Cat. No. Description Network

Connector

Auxiliary

Power

1732E-IB16M12 EtherNet 24V DC 16 Input

Single D-Code M12 Single 4-pin

mini

1732E-OB16M12 EtherNet 24V DC 16, 2 A Output

1732E-16CFGM12 EtherNet 24V DC 16 Selectable

Points

1732E-IB16M12W EtherNet 24V DC 16 Input

WeldBlock Metal Housing

Single D-Code M12 Single 4-pin

mini1732E-16CFGM12W EtherNet 24V DC 16 Selectable

Points

WeldBlock Metal Housing

ArmorBlock 16-Point EtherNet/IP Module, Series A 7

Publication 1732E-IN002B-EN-E - February 2011

of the module. Use a small blade screwdriver to rotate the switches. Line up

the small notch on the switch with the number setting you wish to use. Valid

settings range from 001...254.

Network Address Example

When the switches are set to a valid number, the I/O block’s IP address is

192.168.1.xxx (where xxx represents the number set on the switches). The

I/O block’s subnet mask is 255.255.255.0 and the gateway address is set to

0.0.0.0. When the I/O block uses the network address set on the switches, the

I/O block does not have a host name assigned to it or use any Domain Name

Server.

If the switches are set to an invalid number–for example, 000 or a value

greater than 254 excluding 888–the I/O block checks to see if DHCP is

enabled. If DHCP is enabled, the I/O block asks for an address from a

DHCP server. The DHCP server also assigns other Transport Control

Protocol (TCP) parameters.

If DHCP is not enabled, the I/O block uses the IP address, along with other

TCP configurable parameters, stored in nonvolatile memory.

Mount the Module

Mount the module directly to a machine using two mounting holes, 5.3 mm

(0.208 in.) in diameter. Mounting holes accommodate #6 (M3) pan head

screws. The torque specification is 6.912 cm-kg (6 in-lbs).

This example shows

the network address

set at 163.

44233

8ArmorBlock 16-Point EtherNet/IP Module, Series A

Publication 1732E-IN002B-EN-E - February 2011

Product Dimensions

Refer to the mounting dimensions illustration to help you mount the

modules.

Mount the Module in High Vibration Areas

If you mount the module in an area that is subject to shock or vibration, we

recommend you use a flat and a lock washer to mount the module. Mount the

flat and the lock washer as shown in the mounting illustration. Torque the

mounting screws to 6.912 cm-kg (6 in-lbs).

312

65 mm

(2.56 in.) 43.25 mm

(1.70 in.)

179 mm (7.05 in.)

Front View Side View

26.5 mm

(1.04 in.)

169 mm (6.64 in.)

44234

ArmorBlock 16-Point EtherNet/IP Module, Series A 9

Publication 1732E-IN002B-EN-E - February 2011

High Vibration Area Mounting

Connect the I/O, Network and Auxiliary Cables to the

ArmorBlock Module

The ArmorBlock EtherNet/IP family has 5-pin micro-style connectors.

We provide caps to cover the unused connectors on your module. Connect

the quick-disconnect cord sets you selected for your module to the

appropriate ports.

44235

Flat Washer

Lock Washer

10 ArmorBlock 16-Point EtherNet/IP Module, Series A

Publication 1732E-IN002B-EN-E - February 2011

Network Connectors

Refer to the pinout diagrams for the network connectors.

IMPORTANT

Use the 1585D–M4DC–H: Polyamide small body unshielded or the

1585D–M4DC–SH: Zinc die-cast large body shielded mating

connectors for the D-Code M12 female network connector.

When using shielded (STP) cable with metal housing WeldBlock

products 1732E-IB16M12W and 1732E-16CFGM12W, isolate the

shield at the ArmorBlock end of the cable. This minimizes the

effect of ground offsets.

IMPORTANT

Use two twisted pair CAT5E UTP or STP cable.

D-Code M12 Female Network Connector

44236

(View into Connector)

Pin 1 M12_Tx+

Pin 2 M12_Rx+

Pin 3 M12_Tx-

Pin 4 M12_Rx-

Pin 5 Connector Shell Shield GND

D-Code M12

Wire Color Signal 8-way Modular

RJ45 Pin

1 White-Orange TX+ 1

2 White-Green RX+ 3

3 Orange TX- 2

4 Green RX- 6

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Allen-Bradley Steuereinheit Handbücher

Allen-Bradley

Allen-Bradley MicroLogix 1200 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Kinetix 5700 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet 1747-SCNR Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 20-HIM-A3 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1203-GD2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1762-IQ8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorPoint A Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley Compact 5000 Bedienungsanleitung

Allen-Bradley

Allen-Bradley OptiSIS 1711-P05SISID050S Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 DeviceNet Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756-L7 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley SERCOS 1756-M03SE/A Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock Series Handbuch

Allen-Bradley

Allen-Bradley 1203-GD1 Stücklistenhandbuch

Allen-Bradley

Allen-Bradley FLEX I/O 1794-OB8EP Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1770-KFDG Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-OX8I Bedienungsanleitung

Allen-Bradley

Allen-Bradley Micrologix 1500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-OBDS Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-OBN Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-ADN Bedienungsanleitung

Allen-Bradley

Allen-Bradley DH485/RS-232C Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung