Allen-Bradley FLEX I/O 1794-OB8EP Bedienungsanleitung

  %  &$!$ #

#( '&#!&#" " ' &#"   ) 

   

 



(Cat. No. 1794-OB8EP)















 

This module mounts on a 1794 terminal base unit.

1. Rotate keyswitch (1) on terminal base unit (2) clockwise to position 2

as required for this type of module.

2. Make certain the flexbus connector (3) is pushed all the way to the left

to connect with the neighboring terminal base/adapter. You cannot

install the module unless the connector is fully extended.

3. Make sure that the pins on the bottom of the module are straight so

they will align properly with the connector in the terminal base unit.

WARNING

!If you remove or insert the module while the

backplane power is on, an electrical arc can occur.

This could cause an explosion in hazardous location

installations. Be sure that power is removed or the

area is nonhazardous before proceeding.

4. Position the module (4) with its alignment bar (5) aligned with the

groove (6) on the terminal base.

Installation Instructions

24V dc

FLEX I/O Electronically Fused 8 Output Module2

    

5. Press firmly and evenly to seat the module in the terminal base unit.

The module is seated when the latching mechanism (7) is locked into

the module.

  

Because of the variety of uses for the products described in this publication, those

responsible for the application and use of these products must satisfy themselves

that all necessary steps have been taken to assure that each application and use

meets all performance and safety requirements, including any applicable laws,

regulations, codes and standards. In no event will Allen–Bradley be responsible or

liable for indirect or consequential damage resulting from the use or application of

these products.

Any illustrations, charts, sample programs, and layout examples shown in this

publication are intended solely for purposes of example. Since there are many

variables and requirements associated with any particular installation,

Allen–Bradley does not assume responsibility or liability (to include intellectual

property liability) for actual use based upon the examples shown in this publication.

Allen–Bradley publication SGI–1.1, Safety Guidelines for Application, Installation,

and Maintenance of Solid–State Control (available from your local Allen–Bradley

office), describes some important differences between solid–state equipment and

electromechanical devices that should be taken into consideration when applying

products such as those described in this publication.

Reproduction of the contents of this copyrighted publication, in whole or part,

without written permission of Rockwell Automation, is prohibited.

Throughout this publication, notes may be used to make you aware of safety

considerations. The following annotations and their accompanying statements help

you to identify a potential hazard. avoid a potential hazard, and recognize the

consequences of a potential hazard.

WARNING

!Identifies information about practices or

circumstances that can cause an explosion in a

hazardous environment, which may lead to personal

injury or death, property damage, or economic loss.

ATTENTION

!Identifies information about practices or

circumstances that can lead to personal injury or

death, property damage, or economic loss.

24V dc

FLEX I/O Electronically Fused 8 Output Module 3

    

IMPORTANT Identifies information that is critical for successful

application and understanding of the product.

ATTENTION

Environment and Enclosure

This equipment is intended for use in a Pollution Degree 2

industrial environment, in overvoltage Category II

applications (as defined in IEC publication 60664–1), at

altitudes up to 2000 meters without derating.

This equipment is considered Group 1, Class A industrial

equipment according to IEC/CISPR Publication 11.

Without appropriate precautions, there may be potential

difficulties ensuring electromagnetic compatibility in other

environments due to conducted as well as radiated

disturbance.

This equipment is supplied as “open type” equipment. It

must be mounted within an enclosure that is suitably

designed for those specific environmental conditions that

will be present, and appropriately designed to prevent

personal injury resulting from accessibility to live parts.

The interior of the enclosure must be accessible only by

the use of a tool. Subsequent sections of this publication

may contain additional information regarding specific

enclosure type ratings that are required to comply with

certain product safety certifications.

See NEMA Standards publication 250 and IEC publication

60529, as applicable, for explanations of the degrees of

protection provided by different types of enclosures. Also,

see the appropriate sections in this publication, as well as

the Allen–Bradley publication 1770–4.1, (“Industrial

Automation Wiring and Grounding Guidelines”), for

additional installation requirements pertaining to this

equipment.

24V dc

FLEX I/O Electronically Fused 8 Output Module4

    

ATTENTION

!FLEX I/O is grounded through the DIN rail to

chassis ground. Use zinc plated, yellow chromated

steel DIN rail to assure proper grounding. Using

other DIN rail materials (e.g. aluminum, plastic, etc.)

which can corrode, oxidize or are poor conductors

can result in improper or intermittent platform

grounding.

ATTENTION   

This equipment is sensitive to electrostatic discharge,

which can cause internal damage and affect normal

operation. Follow these guidelines when you handle

this equipment:

•Touch a grounded object to discharge potential

static.

•Wear an approved grounding wriststrap.

•Do not touch connectors or pins on component

boards.

•Do not touch circuit components inside the

equipment.

•If available, use a static–safe workstation.

•When not in use, keep modules in appropriate

static–safe packaging.

ATTENTION Remove field-side power before removing or

inserting this module. This module is designed so

you can remove and insert it under backplane

power. When you remove or insert a module with

field-side power applied, an electrical arc may occur.

An electrical arc can cause personal injury or

property damage by:

•sending an erroneous signal to your system’s field

devices causing unintended machine motion

•causing an explosion in a hazardous environment

Repeated electrical arcing causes excessive wear to

contacts on both the module and its mating

connector. Worn contacts may create electrical

resistance.

24V dc

FLEX I/O Electronically Fused 8 Output Module 5

    

Wiring to a 1794ĆTB2, ĆTB3 or ĆTB3S Terminal Base Unit

WARNING

!If you connect or disconnect wiring while the

fieldside power is on, an electrical arc can occur.

This could cause an explosion in hazardous location

installations. Be sure that power is removed or the

area is nonhazardous before proceeding.

1. Connect individual output wiring (customer loads) to even-numbered

terminals 0 through 14 on the 0 to 15 row (A).

2. Connect the associated return to the corresponding terminal on the

16–33 row (B) or to the odd-numbered terminals on the 0–15 row (A)

as indicated in the wiring table below. (Returns are internally

connected together.)

3. Connect +24V dc power to terminal 34 on the 34–51 row (C).

4. If continuing power to the next terminal base unit, connect a jumper

from terminal 51 (+24V dc) on this base unit to terminal 34 on the

next base unit.

5. Connect 24V dc return to terminal 16 on the 16–33 row (B).

6. If continuing 24V return to the next terminal base unit, connect a

jumper from terminal 33 (return) on this base unit to terminal 16 on

the next base unit.

                

               



 

                



1794ĆTB3

0 -15

34-51

16-33

24V dc

FLEX I/O Electronically Fused 8 Output Module6

Pu lication 1794-IN020B-EN-P - May 2002

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

18 19 20 21 22 23 3324 25 26 27 28 29 30 31 3217

35 36 37 38 47 48 49 5034 51

La el placed at top of wiring area.

Row A

Row B

Row C

Row A

Row B

Row C

39 40 41 42 43 44 45 46



 

 

 

   

0 AĆ0 AĆ11/BĆ17

1 AĆ2 AĆ31/BĆ19

2 AĆ4 AĆ51/BĆ21

3 AĆ6 AĆ71/BĆ23

4 AĆ8 AĆ91/BĆ25

5 AĆ10 AĆ111/BĆ27

6 AĆ12 AĆ131/BĆ29

7 AĆ14 AĆ151/BĆ31

A = output terminals

B = common terminals

C = Power terminals (CĆ34 thru 51 for 1794ĆTB3)

1AĆ1, 3, 5, 7, 9, 11, 13 and 15 are connected together inside the module to 24V dc common.

ATTENTION Total current draw through the terminal base unit is

limited to 10A. Separate power connections to the

terminal base unit may be necessary.

24V dc

FLEX I/O Electronically Fused 8 Output Module 7

'&"!   * 

Wiring to a 1794ĆTBN Terminal Base Unit

WARNING

!If you connect or disconnect wiring while the

fieldside power is on, an electrical arc can occur.

This could cause an explosion in hazardous location

installations. Be sure that power is removed or the

area is nonhazardous before proceeding.

1. Connect individual output wiring (customer loads) to even numbered

terminals (0 thru 14) on row (B).

2. Connect customer load returns to odd numbered terminals (1 thru 15)

on row (C) as indicated in the table below.

3. Connect 24V dc return to terminal 16 on row (B).

4. If continuing the dc return bus to the next terminal base unit, connect

a jumper from terminal 33 on this base unit to terminal 16 on the next

base unit.

5. Connect +24V dc power to terminal 34 on row (C).

6. If continuing dc power to the next terminal base unit, connect a

jumper from terminal 51 (+24V dc) to terminal 34 on the next base

unit.





  



16, 0, 2, 4, 6,

8, 10, 12, 14, 33

34, 1, 3, 5, 7,

9, 11, 13, 15, 51 C

1794ĆTBN

 (! ' $ $ !%  &$' 

  ' $ $ !%  &$' 

1794ĆTBN

O tp t Terminal Common Terminal

+ +

+ +

+ +

+ +

+ +

+ +

+ +

+ +

  (! !' $ "'&#'& &$ !%  &$'   " "! &$ !%  ! 

  ")$ $ !% + ! + ! " !' $ "'&#'& " "! &$ !%  &$' 

24V dc

FLEX I/O Electronically Fused 8 Output Module8

&"! %!$#   ' 



   









       





= Status Indicators () – yellow – show status of individual outputs.

= Diagnostic indicators () – red – when lit, indicates fault

= Insertable label for writing input designations

= Reset button – press to reset fault

   

Faults can be reset 3 ways:

•press the fault reset button

•toggle the output reset bit (write word 1, bit 08)

•cycle backplane power

The reset function resets all output fault bits simultaneously. Non-faulted

outputs remain unaffected during the reset

Using the Fault Reset Button

When you press the manual reset button:

•the fault indicator for the faulted output turns off for about 1.2s (the

faulted output will not attempt to turn on during this delay)

•after the 1.2s delay, the faulted output attempts to turn on

•if the external condition causing the fault is corrected, the output will

remain on, the fault indicator is off, and the status indicator is on

24V dc

FLEX I/O Electronically Fused 8 Output Module 9

Publication 1794-I 020B-E -P - May 2002

Image Table Mapping

Decimal Bit

15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00

IW F7 F6 F5 F4 F3 F2 F1 F0 Reserved (see note)

OW ot used FR O7 O6 O5 O4 O3 O2 O1 O0

OW2 Reserved

Where: IW = input word

OW = output word

F = overload fault bits-1=fault present;0=nofault

O= output data (O0 corresponds to output 0, O1 corresponds to output 2, etc.)

FR = fault reset bit-1=reset output;0=nochange.

Note: The unused lower byte in read word 1 floats during operation. Do not use this byte for fault

status. See Programming" below.

Programming

If your program automatically checks for fault bits, bits 8 through 15 of

read word 1 must be masked. This is a sample program for a module at

rack address 1, group 0. Add similar rungs to your program.

MVM

MASKED MOVE

Source:

Mask:

Destination:

I:010

FF00

9:0

CMP

Compare

Expression

9:0<>0

Out()

O:000

This rung masked bits 8 thru 15.

This rung turns on output if a fault occurs.

24V dc

FLEX I/O Electronically Fused 8 Output Module10

Publication 1794-IN020B-EN-P - May 2002

The f ll wing inf rmati n applies when perating this equipment in hazard us

l cati ns:

Products marked CL I, DI 2, GP A, B, C, D" are suitable for use in Class I Division 2 Groups A, B, C,

and D Hazardous Locations and nonhazardous locations only. Each product is supplied with markings

on the rating nameplate indicating the hazardous location temperature code. When combining products

within a system, the most adverse temperature code (lowest T" number) may be used to help

determine the overall temperature code of the system. Combinations of equipment in your system are

subject to investigation by the local Authority Having Jurisdiction at the time of installation.

WARNING EXPLOSION HAZARD -

•Do not disconnect equipment unless power has been removed or the

area is known to be nonhazardous.

•Do not disconnect connections to this equipment unless power has

been removed or the area is known to be nonhazardous. Secure any

external connections that mate to this equipment by using screws,

sliding latches, threaded connectors, or other means provided with this

product.

•Substitution of components may impair suitability for Class I, Division 2.

•If this product contains batteries, they must only be changed in an area

known to be nonhazardous.

Informations sur l'utilisation de cet équipement en environnements dangereux:

Les produits marqués CL I, DI 2, GP A, B, C, D ne conviennent que une utilisation en environnements

de Classe I Division 2 Groupes A, B, C, D dangereux et non dangereux. Chaque produit est livré avec

des marquages sur sa plaque d'identification qui indiquent le code de température pour les

environnements dangereux. Lorsque plusieurs produits sont combinés dans un systéme, le code de

température le plus défavorable (code de température le plus faible) peut eatre utilisé pour déterminer

le code de température global du systéme. Les combinaisons d'equipements dans le systéme sont

sujettes à inspection par les autorités locales qualifiées au moment de l'installation.

AVERTISSEMENT

RISQUE D'EXPLOSION -

•Couper le courant ou s'assurer que l'environnement est classé non

dangereux avant de débrancher l'équipement.

•Couper le courant ou s'assurer que l'environnement est classé non

dangereux avant de débrancher les connecteurs. Fixer tous les

connecteurs externes reliés à cet équipement à l'aide de vis, loquets

coulissants, connecteurs filetés ou autres moyens fournis avec ce

produit.

•La substitution de composants peut rendre cet équipement inadapté à

une utilisation en environnement de Classe 1, Division 2.

•S'assurer que l'environnement est classé non dangereux avant de

changer les piles.

Andere Handbücher für FLEX I/O 1794-OB8EP

Inhaltsverzeichnis

Andere Allen-Bradley Steuereinheit Handbücher

Allen-Bradley

Allen-Bradley 1771-OBDS Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1200 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 750 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley C Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley C Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley DH485/RS-232C Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-QDC Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756-EN2TSC Bedienungsanleitung

Allen-Bradley

Allen-Bradley Micrologix 1500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-12X4M12QCDR Handbuch

Allen-Bradley

Allen-Bradley ControlLogix DeviceNet 1756-DNB Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix ControlNet Scanner Module Service-Handbuch

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-OB16M12R Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1770-KFDG Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet Ex 1797-RPA Bedienungsanleitung

Allen-Bradley

Allen-Bradley OptiSIS 1711-P05SISID050S Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-OX8I Bedienungsanleitung

Allen-Bradley

Allen-Bradley D Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1500 1764-MM1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 755 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-ENET/B Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-VHSC5 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2711P-RN6K Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1606-XLBRED20 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung