Allen-Bradley ControlLogix 1756-OV32E Bedienungsanleitung

Publication 1756-IN582A-EN-P - August 2003

Installation Instructions

ControlLogix

DC (10-30V) Electronically-Fused Sinking

Current Output Module

Catalog Number 1756-OV32E

Obtain a User Manual

This product also has a user manual (pub. no. 1756-UM058). To view

it, visit www.ab.com/manuals or www.theautomationbookstore.com.

To purchase a manual, you can:

•contact your distributor or Rockwell Automation representative

•visit www.theautomationbookstore.com and place an order

•call 800.963.9548 (USA/Canada) or 001.320.725.1574 (outside

USA/Canada)

To: See page:

Obtain a User Manual 1

Identify the Module Components 6

Note the Power Requirements 6

Install the Module 7

Key the Module and Removable Terminal Block/Interface Module 8

Wire the Removable Terminal Block 9

Wire the Module 10

Assemble the Removable Terminal Block and the Housing 11

Install the Removable Terminal Block onto the Module 11

Check the Indicators 12

Remove the Removable Terminal Block from the Module 13

Remove the Module 13

See Specifications 14

Allen-Bradley Parts

2ControlLogix DC (10-30V) Electronically-Fused Sinking Current Output Module

Publication 1756-IN582A-EN-P - August 2003

Important User Information

Solid state equipment has operational characteristics differing from those of

electromechanical equipment. Safety Guidelines for the Application, Installation and

Maintenance of Solid State Controls (Publication SGI-1.1 available from your local Rockwell

Automation sales office or online at http://www.ab.com/manuals/gi) describes some

important differences between solid state equipment and hard-wired electromechanical

devices. Because of this difference, and also because of the wide variety of uses for solid

state equipment, all persons responsible for applying this equipment must satisfy

themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or

consequential damages resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes.

Because of the many variables and requirements associated with any particular installation,

Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on

the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of

information, circuits, equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission

of Rockwell Automation, Inc. is prohibited.

Throughout this manual we use notes to make you aware of safety considerations.

WARNING Identifies information about practices or circumstances that can cause an

explosion in a hazardous environment, which may lead to personal injury or

death, property damage, or economic loss.

ATTENTION

Identifies information about practices or circumstances that can lead to personal

injury or death, property damage, or economic loss. Attentions help you:

•identify a hazard

•avoid a hazard

•recognize the consequence

IMPORTANT Identifies information that is critical for successful application and

understanding of the product.

SHOCK HAZARD Labels may be located on or inside the drive to alert people that dangerous

voltage may be present.

ControlLogix DC (10-30V) Electronically-Fused Sinking Current Output Module 3

Publication 1756-IN582A-EN-P - August 2003

Environment and Enclosure

Prevent Electrostatic Discharge

ATTENTION

This equipment is intended for use in a Pollution Degree 2 industrial

environment, in overvoltage Category II applications (as defined in IEC

publication 60664-1), at altitudes up to 2000 meters without derating.

This equipment is considered Group 1, Class A industrial equipment

according to IEC/CISPR Publication 11. Without appropriate precautions,

there may be potential difficulties ensuring electromagnetic compatibility in

other environments due to conducted as well as radiated disturbance.

This equipment is supplied as "open type" equipment. It must be mounted

within an enclosure that is suitably designed for those specific

environmental conditions that will be present and appropriately designed to

prevent personal injury resulting from accessibility to live parts. The interior

of the enclosure must be accessible only by the use of a tool. Subsequent

sections of this publication may contain additional information regarding

specific enclosure type ratings that are required to comply with certain

product safety certifications.

NOTE: See NEMA Standards publication 250 and IEC publication 60529, as

applicable, for explanations of the degrees of protection provided by

different types of enclosure. Also, see the appropriate sections in this

publication, as well as the Allen-Bradley publication 1770-4.1 ("Industrial

Automation Wiring and Grounding Guidelines"), for additional installation

requirements pertaining to this equipment.

ATTENTION

This equipment is sensitive to electrostatic discharge, which can cause

internal damage and affect normal operation. Follow these guidelines when

you handle this equipment:

•Touch a grounded object to discharge potential static.

•Wear an approved grounding wriststrap.

•Do not touch connectors or pins on component boards.

•Do not touch circuit components inside the equipment.

•If available, use a static-safe workstation.

When not in use, store the equipment in appropriate static-safe packaging.

Allen-Bradley Parts

4ControlLogix DC (10-30V) Electronically-Fused Sinking Current Output Module

Publication 1756-IN582A-EN-P - August 2003

Removal and Insertion Under Power

Be sure that power is removed or the area is nonhazardous before

proceeding. Repeated electrical arcing causes excessive wear to

contacts on both the module and its mating connector. Worn contacts

may create electrical resistance that can affect module operation.

North American Hazardous Location Approval

WARNING When you insert or remove the module while backplane

power is on, an electrical arc can occur. This could cause

an explosion in hazardous location installations.

The following information applies when

operating this equipment in hazardous

locations:

Informations sur l’utilisation de cet équipement

en environnements dangereux :

Products marked “CL I, DIV 2, GP A, B, C, D” are

suitable for use in Class I Division 2 Groups A, B,

C, D, Hazardous Locations and nonhazardous

locations only. Each product is supplied with

markings on the rating nameplate indicating the

hazardous location temperature code. When

combining products within a system, the most

adverse temperature code (lowest “T” number)

may be used to help determine the overall

temperature code of the system. Combinations

of equipment in your system are subject to

investigation by the local Authority Having

Jurisdiction at the time of installation.

Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne

conviennent qu’à une utilisation en environnements de

Classe I Division 2 Groupes A, B, C, D dangereux et

non dangereux. Chaque produit est livré avec des

marquages sur sa plaque d’identification qui indiquent

le code de température pour les environnements

dangereux. Lorsque plusieurs produits sont combinés

dans un système, le code de température le plus

défavorable (code de température le plus faible) peut

être utilisé pour déterminer le code de température

global du système. Les combinaisons d’équipements

dans le système sont sujettes à inspection par les

autorités locales qualifiées au moment de

l’installation.

ControlLogix DC (10-30V) Electronically-Fused Sinking Current Output Module 5

Publication 1756-IN582A-EN-P - August 2003

WARNING EXPLOSION HAZARD

•Do not disconnect

equipment unless

power has been

removed or the area

is known to be

nonhazardous.

•Do not disconnect

connections to this

equipment unless

power has been

removed or the area

is known to be

nonhazardous.

Secure any external

connections that

mate to this

equipment by using

screws, sliding

latches, threaded

connectors, or other

means provided

with this product.

•Substitution of

components may

impair suitability for

Class I, Division 2.

•If this product

contains batteries,

they must only be

changed in an area

known to be

nonhazardous.

AVERTISSEMENT

RISQUE D’EXPLOSION

•Couper le courant ou

s’assurer que

l’environnement est

classé non dangereux

avant de débrancher

l'équipement.

•Couper le courant ou

s'assurer que

l’environnement est

classé non dangereux

avant de débrancher

les connecteurs. Fixer

tous les connecteurs

externes reliés à cet

équipement à l'aide

de vis, loquets

coulissants,

connecteurs filetés ou

autres moyens fournis

avec ce produit.

•La substitution de

composants peut

rendre cet équipement

inadapté à une

utilisation en

environnement de

Classe I, Division 2.

•S’assurer que

l’environnement est

classé non dangereux

avant de changer les

piles.

The following information applies when

operating this equipment in hazardous

locations:

Informations sur l’utilisation de cet équipement

en environnements dangereux :

Allen-Bradley Parts

6ControlLogix DC (10-30V) Electronically-Fused Sinking Current Output Module

Publication 1756-IN582A-EN-P - August 2003

Identify the Module Components

You received the following components with your order:

•1756-OV32E module

•Removable Terminal Block (RTB) door label

If you did not receive these components, contact your local

distributor Rockwell Automation sales office.

This module mounts in a 1756 chassis and uses a separately-ordered

RTB or a Bulletin 1492 Interface Module (IFM)(1) to connect all

field-side wiring. This module uses one of the following RTBs:

•1756-TBCH 36-position Cage clamp RTB

•1756-TBS6H 36-position Spring clamp RTB

Use an extended-depth cover (1756-TBE) for applications with heavy

gauge wiring or requiring additional routing space. When using an

IFM, consult the documentation that came with it to connect wiring.

Note the Power Requirements

This module receives power from the 1756 chassis power supply and

requires 2 sources of power from the ControlLogix backplane:

•390mA at 5.1V dc

•2mA at 24V dc

Add this current/power value (2.04W) to the requirements of all other

modules in the chassis to prevent overloading the power supply.

(1) The Bulletin 1492 IFM may not be used in any application that requires agency certification of the

ControlLogix®system. Use of the IFM violates the UL, CSA and FM certifications of this product.

IMPORTANT Before you install your module, you should:

•install and ground a 1756 chassis and power supply.

•order and receive an RTB or IFM, and its

components, for your application.

ControlLogix DC (10-30V) Electronically-Fused Sinking Current Output Module 7

Publication 1756-IN582A-EN-P - August 2003

Install the Module

You can install or remove the module while chassis power is applied.

Be sure that power is removed or the area is nonhazardous before

proceeding. Repeated electrical arcing causes excessive wear to

contacts on both the module and its mating connector. Worn contacts

may create electrical resistance that can affect module operation.

1. Align the circuit board with the top and bottom chassis guides.

2. Slide the module into chassis until module locking tabs click.

WARNING When you insert or remove the module while backplane

power is on, an electrical arc can occur. This could cause

an explosion in hazardous location installations.

20861–M

Printed

Circuit

Board

Locking tab

Allen-Bradley Parts

8ControlLogix DC (10-30V) Electronically-Fused Sinking Current Output Module

Publication 1756-IN582A-EN-P - August 2003

Key the Module and Removable Terminal Block/Interface Module

Use the wedge-shaped keying tabs and U-shaped keying bands to

prevent connecting the wrong wires to your module.

Key positions on the module that correspond to unkeyed positions

on the RTB. For example, if you key the first position on the module,

leave the first position on the RTB unkeyed.

1. To key the module, insert the U-shaped band, as shown.

2. Push the band until it snaps in place.

3. To key the RTB or IFM, insert the wedge-shaped tab with

rounded edge first, as shown.

4. Push the tab until it stops.

Reposition the tabs to rekey future module applications.

20850–M

U-shaped

bands

20851–M

Wedge-shaped tab

ControlLogix DC (10-30V) Electronically-Fused Sinking Current Output Module 9

Publication 1756-IN582A-EN-P - August 2003

Wire the Removable Terminal Block

Wire the RTB with a 1/8 inch (3.2mm) maximum flat-bladed

screwdriver before installing it onto the module.

Be sure that power is removed or the area is nonhazardous before

proceeding.

WARNING When you connect or disconnect the Removable

Terminal Block (RTB) with field side power applied, an

electrical arc can occur. This could cause an explosion in

hazardous location installations.

Spring Clamp RTB Cage Clamp RTB

20860-M 20859-M

1. Strip 7/16 inch (11mm) maximum

length of wire.

2. Insert the screwdriver into the

inner hole of the RTB.

3. Insert the wire into the

open terminal and

remove the screwdriver.

1. Strip 3/8 inch (9.5mm) maximum

length of wire.

2. Insert the wire into the open terminal.

3. Turn the screw clockwise to close the

terminal on the wire.

Allen-Bradley Parts

10 ControlLogix DC (10-30V) Electronically-Fused Sinking Current Output Module

Publication 1756-IN582A-EN-P - August 2003

Wire the Module

You can only connect wiring to your module with an RTB or IFM.

After completing field-side wiring, secure the wires in the strain relief

area with a cable-tie.

43386-M

910

1112

1314

1516

1718

1920

2122

2324

2526

2728

2930

3132

3334

3536

Daisy chain to

other RTBs

Daisy chain to

other RTBs

1. When you daisy chain from a group to another RTB, always connect the daisy

chain to the terminal directly connected to the supply wire, as shown above.

2. This wiring example uses a single voltage source.

3. If separate power sources are used, do not exceed the specified isolation voltag

4. Do not physically connect more than two wires to a single RTB terminal.

Group 0

Group 1

Group 0

Group 1

DC COM

OUT-1

OUT-3

OUT-5

OUT-7

OUT-9

OUT-11

OUT-13

OUT-15

DC-0(+)

DC-1(+)

OUT-0

OUT-2

OUT-4

OUT-6

OUT-8

OUT-10

OUT-12

OUT-14

RTN OUT-0

RTN OUT-1

OUT-17

OUT-19

OUT-21

OUT-23

OUT-25

OUT-27

OUT-29

OUT-31

OUT-16

OUT-18

OUT-20

OUT-22

OUT-24

OUT-26

OUT-28

OUT-30

1756-OV32E

NOTES:

Inhaltsverzeichnis

Andere Allen-Bradley Steuereinheit Handbücher

Allen-Bradley

Allen-Bradley 1757-ABRIO Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerMonitor 500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-8IOLM12R Bedienungsanleitung

Allen-Bradley

Allen-Bradley Entek XM-123 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley Series B Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O 1794-OB8EP Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet 1788-CNCR Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1769-ASCII Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix SynchLink 1756-SYNCH Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet-to-DeviceNet 1788-CN2DN Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IE8H Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet 1747-ACN15 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-DH485 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-OW Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-PLS Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1606-XLS960BUFFER Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1200 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1734-IB8S Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock Series Handbuch

Allen-Bradley

Allen-Bradley ArmorBlock 1732E Handbuch

Allen-Bradley

Allen-Bradley POINT I/O 1734-OB2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-IA8D Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung