Allen-Bradley POINT I/O 1734-PDN Bedienungsanleitung

Installation Instructions

POINT I/O DeviceNet Communication

Interface Module

Catalog Number 1734-PDN, Series B

Table of Contents

Topic Page

Important User Information 2

Environment and Enclosure 3

Preventing Electrostatic Discharge 3

North American Hazardous Location Approval 4

European Hazardous Location Approval 5

Identify Module Components 6

Install the Module 7

Install the Module in an Existing System 8

Wire the Module 9

Troubleshoot with Indicators 12

Specifications 13

2POINT I/O DeviceNet Communication Interface Module

Publication 1734-IN057E-EN-E - October 2015

Important User Information

Solid-state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls

(Publication SGI-1.1 available from your local Rockwell Automation sales office or online at

http://www.rockwellautomation.com/literature/) describes some important differences between

solid-state equipment and hard-wired electromechanical devices. Because of this difference, and also

because of the wide variety of uses for solid-state equipment, all persons responsible for applying this

equipment must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular installation, Rockwell Automation, Inc.

cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING: Identifies information about practices or circumstances that can cause an

explosion in a hazardous environment, which may lead to personal injury or death,

property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to

personal injury or death, property damage, or economic loss. Attentions help you

identify a hazard, avoid a hazard and recognize the consequences.

SHOCK HAZARD: Labels may be on or inside the equipment (for example, drive or

motor) to alert people that dangerous voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment (for example, drive or

motor) to alert people that surfaces may reach dangerous temperatures.

IMPORTANT Identifies information that is critical for successful application and understanding of

the product.

POINT I/O DeviceNet Communication Interface Module 3

Publication 1734-IN057E-EN-E - October 2015

Environment and Enclosure

Preventing Electrostatic Discharge

ATTENTION: This equipment is intended for use in a Pollution Degree 2

industrial environment, in overvoltage Category II applications (as defined in IEC

publication 60664-1), at altitudes up to 2000 meters without derating.

This equipment is not intended for use in residential environments and may not

provide adequate protection to radio communication services in such

environments.

This equipment is considered Group 1, Class A industrial equipment according

to IEC/CISPR Publication 11. Without appropriate precautions, there may be

potential difficulties ensuring electromagnetic compatibility in other

environments due to conducted as well as radiated disturbance.

This equipment is supplied as “open type” equipment. It must be mounted

within an enclosure that is suitably designed for those specific environmental

conditions that will be present and appropriately designed to prevent personal

injury resulting from accessibility to live parts. The interior of the enclosure

must be accessible only by the use of a tool. Subsequent sections of this

publication may contain additional information regarding specific enclosure type

ratings that are required to comply with certain product safety certifications.

In addition to this publication, see:

• Industrial Automation Wiring and Grounding Guidelines, publication

1770-4.1, for additional installation requirements.

• NEMA Standard 250 and IEC 60529, as applicable, for explanations of the

degrees of protection provided by enclosures.

ATTENTION: This equipment is sensitive to electrostatic discharge, which can

cause internal damage and affect normal operation. Follow these guidelines

when you handle this equipment:

• Touch a grounded object to discharge potential static.

• Wear an approved grounding wriststrap.

• Do not touch connectors or pins on component boards.

• Do not touch circuit components inside the equipment.

• Use a static-safe workstation, if available.

• Store the equipment in appropriate static-safe packaging when not in use.

4POINT I/O DeviceNet Communication Interface Module

Publication 1734-IN057E-EN-E - October 2015

North American Hazardous Location Approval

ATTENTION: This product is grounded through the DIN rail to chassis ground.

Use zinc plated yellow-chromate steel DIN rail to assure proper grounding. The

use of other DIN rail materials (for example, aluminum or plastic) that can

corrode, oxidize, or are poor conductors, can result in improper or intermittent

grounding. Secure DIN rail to mounting surface approximately every 200 mm

(7.8 in.) and use end-anchors appropriately.

The following information applies when

operating this equipment in hazardous

locations:

Informations sur l'utilisation de cet équipement

en environnements dangereux:

Products marked "CL I, DIV 2, GP A, B, C, D" are suitable

for use in Class I Division 2 Groups A, B, C, D, Hazardous

Locations and nonhazardous locations only. Each product

is supplied with markings on the rating nameplate

indicating the hazardous location temperature code.

When combining products within a system, the most

adverse temperature code (lowest "T" number) may be

used to help determine the overall temperature code of

the system. Combinations of equipment in your system

are subject to investigation by the local Authority Having

Jurisdiction at the time of installation.

Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne conviennent

qu'à une utilisation en environnements de Classe I Division 2

Groupes A, B, C, D dangereux et non dangereux. Chaque produit

est livré avec des marquages sur sa plaque d'identification qui

indiquent le code de température pour les environnements

dangereux. Lorsque plusieurs produits sont combinés dans un

système, le code de température le plus défavorable (code de

température le plus faible) peut être utilisé pour déterminer le

code de température global du système. Les combinaisons

d'équipements dans le système sont sujettes à inspection par

les autorités locales qualifiées au moment de l'installation.

EXPLOSION HAZARD

• Do not disconnect equipment unless

power has been removed or the area is

known to be nonhazardous.

• Do not disconnect connections to this

equipment unless power has been

removed or the area is known to be

nonhazardous. Secure any external

connections that mate to this equipment

by using screws, sliding latches,

threaded connectors, or other means

provided with this product.

• Substitution of components may impair

suitability for Class I, Division 2.

• If this product contains batteries, they

must only be changed in an area known

to be nonhazardous.

RISQUE D’EXPLOSION

• Couper le courant ou s'assurer que

l'environnement est classé non dangereux

avant de débrancher l'équipement.

• Couper le courant ou s'assurer que

l'environnement est classé non dangereux

avant de débrancher les connecteurs. Fixer

tous les connecteurs externes reliés à cet

équipement à l'aide de vis, loquets

coulissants, connecteurs filetés ou autres

moyens fournis avec ce produit.

• La substitution de composants peut rendre cet

équipement inadapté à une utilisation en

environnement de Classe I, Division 2.

• S'assurer que l'environnement est classé non

dangereux avant de changer les piles.

POINT I/O DeviceNet Communication Interface Module 5

Publication 1734-IN057E-EN-E - October 2015

European Hazardous Location Approval

The following applies when the product bears the Ex Marking

This equipment is intended for use in potentially explosive atmospheres as defined by

European Union Directive 94/9/EC.

DEMKO certifies that this equipment has been found to comply with the Essential Health

and Safety Requirements relating to the design and construction of Category 3 equipment

intended for use in Zone 2 potentially explosive atmospheres, given in Annex II to this

Directive.

Compliance with the Essential Health and Safety Requirements has been assured by

compliance with EN 60079-0:2012+A11:2013, EN 60079-15:2010, reference certificate

number DEMKO 04ATEX0330347X.

ATTENTION: This equipment is not resistant to sunlight or other sources of

UV radiation.

WARNING: This equipment shall be mounted in an ATEX certified enclosure

with a minimum ingress protection rating of at least IP54 (as defined in

IEC60529) and used in an environment of not more than Pollution Degree 2 (as

defined in IEC 60664-1) when applied in Zone 2 environments. The enclosure

must utilize a tool removable cover or door.

WARNING: This equipment shall be used within its specified ratings defined

by Rockwell Automation.

WARNING: Provision shall be made to prevent the rated voltage from being

exceeded by transient disturbances of more than 140% of the rated voltage

when applied in Zone 2 environments.

WARNING: The secondary of a current transformer shall not be

open-circuited when applied in Class I, Zone 2 environments.

WARNING: This equipment must be used only with ATEX certified Rockwell

Automation backplanes

WARNING: Secure any external connections that mate to this equipment by

using screws, sliding latches, threaded connectors, or other means provided

with this product.

WARNING: Do not disconnect equipment unless power has been removed or

the area is known to be nonhazardous.

6POINT I/O DeviceNet Communication Interface Module

Publication 1734-IN057E-EN-E - October 2015

Identify Module Components

Use the figure to identify the external features of the module.

POINT I/O DeviceNet Communication Interface Module

Module Description

Description Description

1 DeviceNet Connector 6 DIN Rail Locking Screw Orange

2 Module Label 7 Safety End Cap

3 Interlocking Side Pieces 8 RTB Removable Handle

4 System Power Indicator 9 Removable Terminal Block (RTB)

5 DeviceNet Power Indicator

31538-M

POINT I/O DeviceNet Communication Interface Module 7

Publication 1734-IN057E-EN-E - October 2015

Install the Module

To install the module on the DIN rail, proceed as follows.

1. Position the module vertically above the DIN rail

2. Press down firmly to install the module on the DIN rail.

The locking mechanism will lock the module to the DIN rail.

3. Remove the safety end cap by sliding it up to expose the backplane and power

interconnections.

ATTENTION: When you insert or remove the module while backplane power is

on, an electrical arc can occur. This could cause an explosion in hazardous

location installations.

Be sure that power is removed or the area is nonhazardous before proceeding.

Repeated electrical arcing causes excessive wear to contacts on both the

module and its mating connector. Worn contacts may create electrical

resistance that can affect module operation.

ATTENTION: Do not discard the end cap. Use this end cap to cover the exposed

interconnections on the last mounting base on the DIN rail. Failure to do so

could result in equipment damage or injury from electric shock.

8POINT I/O DeviceNet Communication Interface Module

Publication 1734-IN057E-EN-E - October 2015

Install the Module in an Existing System

To install a replacement module in an existing system, proceed as follows.

1. To remove the module from the DIN rail, pull up on the RTB removal handle to

remove the terminal block.

2. Use a small-bladed screwdriver to rotate the DIN rail locking screw to a vertical

position. This releases the locking mechanism.

3. Lift straight up to remove.

4. Position the module vertically above the DIN rail.

5. Slide the module down so that the interlocking side pieces engage the adjacent

module.

6. Press firmly to seat the module on the DIN rail.

The module locking mechanism will snap into place.

WARNING: When you connect or disconnect the Removable Terminal Block

(RTB) with field side power applied, an electrical arc can occur. This could cause

an explosion in hazardous location installations.

Be sure that power is removed or the area is nonhazardous before proceeding.

POINT I/O DeviceNet Communication Interface Module 9

Publication 1734-IN057E-EN-E - October 2015

Wire the Module

WARNING: If you connect or disconnect wiring while the field-side power is

on, an electrical arc can occur. This could cause an explosion in hazardous

location installations. Be sure that power is removed or the area is

nonhazardous before proceeding.

NC = No Connection

CHAS GND = Chassis Ground

C = Common

V = Supply

DeviceNet Power

42513

System Power

DeviceNet Connector

CHAS GND

10 POINT I/O DeviceNet Communication Interface Module

Publication 1734-IN057E-EN-E - October 2015

Connect Terminal In Terminal Out

+V DC 6 7

-V DC 4 5

Chas Gnd 2 3

12/24V DC becomes the internal field-power bus for modules to the right.

NC NC

CHAS

GND

V DC

Connect this supply

to the internal

field-power bus.

43960

12/24V DC Wiring

NC = No Connection CHAS GND = Chassis Ground

C = Common V = Supply

12/24V DC

Power

CHAS

GND

Inhaltsverzeichnis

Andere Allen-Bradley Steuereinheit Handbücher

Allen-Bradley

Allen-Bradley PowerFlex 20-HIM-A3 Bedienungsanleitung

Allen-Bradley

Allen-Bradley D Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-OB16 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1757-ABRIO Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-DHRIO Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-OA8K Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix ControlNet B Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IA8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley CENTERLINE 1500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley MSR41 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1746-HSTP1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1788-CN2FFR Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-OF6VI Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-KT/B Installations- und Benutzerhandbuch

Allen-Bradley

Allen-Bradley ControlNet Ex 1797-RPA Bedienungsanleitung

Allen-Bradley

Allen-Bradley XM-124 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 160-RS1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1336 PLUS II Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock Series Handbuch

Allen-Bradley

Allen-Bradley 1771-OBN Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-IT4IM12R Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1200 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-12X4M12QCDR Handbuch

Allen-Bradley

Allen-Bradley Guardmaster 440C-ENET Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung