Allen-Bradley 1757-ABRIO Bedienungsanleitung

Installation Instructions

Process Remote I/O (RIO) Communication

Interface Module

Catalog Number 1757-ABRIO

About This Publication

Use this publication as a guide to install the Process Remote I/O (RIO)

Communication Interface Module. Refer to publication 1757-UM007C, the

1757-ABRIO User Manual, for additional information. You can download a

.pdf file of the manual at: http://literature.rockwellautomation.com.

Topic Page

Important User Information 2

Environment and Enclosure 3

North American Hazardous Location Approval 4

Prevent Electrostatic Discharge 5

Identify Module Features 5

Prepare the Chassis for Module Installation 6

Remove and Insertion Under Power 6

Install the Module 7

Wire the Connector for the Remote I/O Network 8

Status Display Power-up Messages 9

Interpret the Alphanumeric Display 10

Interpret the Status Indicators 11

Configuring the Module 12

Specifications 13

Additional Resources 15

2Process Remote I/O (RIO) Communication Interface Module

Publication 1757-IN916C-EN-P - March 2008

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls

(publication SGI-1.1 available from your local Rockwell Automation sales office or online at

http://literature.rockwellautomation.com) describes some important differences between solid state

equipment and hard-wired electromechanical devices. Because of this difference, and also because of the

wide variety of uses for solid state equipment, all persons responsible for applying this equipment must

satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular installation, Rockwell Automation, Inc.

cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING Identifies information about practices or circumstances that can cause an explosion in

a hazardous environment, which may lead to personal injury or death, property damage,

or economic loss.

IMPORTANT Identifies information that is critical for successful application and understanding of the

product.

ATTENTION Identifies information about practices or circumstances that can lead to personal injury

or death, property damage, or economic loss. Attentions help you to identify a hazard,

avoid a hazard and recognize the consequences.

SHOCK HAZ-

Labels may be on or inside the equipment, such as a drive or motor, to alert people that

dangerous voltage may be present.

URN HAZARD Labels may be on or inside the equipment, such as a drive or motor, to alert people that

surfaces may reach dangerous temperatures.

Process Remote I/O (RIO) Communication Interface Module 3

Publication 1757-IN916C-EN-P - March 2008

Environment and Enclosure

ATTENTION This equipment is intended for use in a Pollution Degree 2 industrial

environment, in overvoltage Category II applications (as defined in IEC

publication 60664-1), at altitudes up to 2000 m (6561 ft) without

derating.

This equipment is considered Group 1, Class A industrial equipment

according to IEC/CISPR Publication 11. Without appropriate

precautions, there may be potential difficulties ensuring

electromagnetic compatibility in other environments due to

conducted as well as radiated disturbance.

This equipment is supplied as open-type equipment. It must be

mounted within an enclosure that is suitably designed for those

specific environmental conditions that will be present and

appropriately designed to prevent personal injury resulting from

accessibility to live parts. The enclosure must have suitable

flame-retardant properties to prevent or minimize the spread of flame,

complying with a flame spread rating of 5VA, V2, V1, V0 (or

equivalent) if non-metallic. The interior of the enclosure must be

accessible only by the use of a tool. Subsequent sections of this

publication may contain additional information regarding specific

enclosure type ratings that are required to comply with certain

product safety certifications.

In addition to this publication, see:

•Industrial Automation Wiring and Grounding Guidelines, for additional

installation requirements, Allen-Bradley publication 1770-4.1.

•NEMA Standards publication 250 and IEC publication 60529, as

applicable, for explanations of the degrees of protection provided by

different types of enclosure.

4Process Remote I/O (RIO) Communication Interface Module

Publication 1757-IN916C-EN-P - March 2008

North American Hazardous Location Approval

The following information applies

when operating this equipment in

hazardous locations.

Informations sur l'utilisation de cet

équipement en environnements

dangereux.

Products marked “CL I, DIV 2, GP A, B, C, D” are

suitable for use in Class I Division 2 Groups A, B,

C, D, Hazardous Locations and nonhazardous

locations only. Each product is supplied with

markings on the rating nameplate indicating the

hazardous location temperature code. When

combining products within a system, the most

adverse temperature code (lowest “T” number)

may be used to help determine the overall

temperature code of the system. Combinations

of equipment in your system are subject to

investigation by the local Authority Having

Jurisdiction at the time of installation.

Les produits marqués “CL I, DIV 2, GP A, B, C, D” ne

conviennent qu'à une utilisation en environnements

de Classe I Division 2 Groupes A, B, C, D dangereux

et non dangereux. Chaque produit est livré avec des

marquages sur sa plaque d'identification qui

indiquent le code de température pour les

environnements dangereux. Lorsque plusieurs

produits sont combinés dans un système, le code de

température le plus défavorable (code de

température le plus faible) peut être utilisé pour

déterminer le code de température global du

système. Les combinaisons d'équipements dans le

système sont sujettes à inspection par les autorités

locales qualifiées au moment de l'installation.

EXPLOSION HAZARD

Do not disconnect equipment

unless power has been

removed or the area is known

to be nonhazardous.

Do not disconnect

connections to this

equipment unless power has

been removed or the area is

known to be nonhazardous.

Secure any external

connections that mate to this

equipment by using screws,

sliding latches, threaded

connectors, or other means

provided with this product.

Substitution of components

may impair suitability for

Class I, Division 2.

If this product contains

batteries, they must only be

changed in an area known to

be nonhazardous.

RISQUE D'EXPLOSION

Couper le courant ou s'assurer

que l'environnement est classé

non dangereux avant de

débrancher l'équipement.

Couper le courant ou s'assurer

que l'environnement est classé

non dangereux avant de

débrancher les connecteurs.

Fixer tous les connecteurs

externes reliés à cet

équipement à l'aide de vis,

loquets coulissants,

connecteurs filetés ou autres

moyens fournis avec ce produit.

La substitution de composants

peut rendre cet équipement

inadapté à une utilisation en

environnement de Classe I,

Division 2.

S'assurer que l'environnement

est classé non dangereux avant

de changer les piles.

WARNING AVERTISSEMENT

Process Remote I/O (RIO) Communication Interface Module 5

Publication 1757-IN916C-EN-P - March 2008

Prevent Electrostatic Discharge

Identify Module Features

ATTENTION This equipment is sensitive to electrostatic discharge, which can

cause internal damage and affect normal operation. Follow these

guidelines when you handle this equipment:

•Touch a grounded object to discharge potential static.

•Wear an approved grounding wriststrap.

•Do not touch connectors or pins on component boards.

•Do not touch circuit components inside the equipment.

•Use a static-safe workstation, if available.

•Store the equipment in appropriate static-safe packaging when

not in use.

The module has:

•a 4-character scrolling display.

•3 status indicators.

RIO indicates the status of the

network.

SYS indicates the connection to the

processor.

OK indicates the module’s own

internal state.

•a 3-pin Phoenix connector that

connects to the remote devices.

RIO SYS OK

43161

6Process Remote I/O (RIO) Communication Interface Module

Publication 1757-IN916C-EN-P - March 2008

Prepare the Chassis for Module Installation

Before you install the 1757-ABRIO module, you must install and connect a

ProcessLogix or ControlLogix chassis and power supply.

Determine Module Slot Location

Chassis slots are numbered starting from the left, starting at 0. Slot 0 is the

first slot to the right of the power supply.

You can:

•use any size chassis.

•install the module in any available slot.

•install multiple 1757-ABRIO modules in the same chassis, depending

on how your power supply is rated.

Remove and Insertion Under Power

You can install or remove the module while the chassis is powered if you

observe these precautions.

WARNING When you insert or removethe module while backplane poweris on,

an electrical arc can occur. If you connect or disconnect the

communications cable with power applied to this module or any

device on the network, an electrical arc can occur. This could cause

an explosion in hazardous location installations.

Be sure that power is removed or the area is nonhazardous before

proceeding.

Repeated electrical arcing causes excessive wear to contacts on

both the module and its mating connector. Worn contacts may create

electrical resistance that can affect module operation.

Process Remote I/O (RIO) Communication Interface Module 7

Publication 1757-IN916C-EN-P - March 2008

Install the Module

To install the module, follow these steps.

1. Align the module circuit board with the top and bottom guides in the

chassis.

2. Slide the module into the chassis in the appropriate slot.

Make sure the module properly connects to the chassis backplane.

The module is fully installed when it is flush with the other installed

modules, and the module locking clips click into place.

3. To remove the module, push down on the locking clips at the top and

bottom of each module.

4. Slide the module out of the chassis.

ATTENTION Do not force the module into the backplane connector. If you cannot

seat the module with firm pressure, check the alignment. Forcing the

module into the chassis can damage the backplane connector or the

module.

43154

8Process Remote I/O (RIO) Communication Interface Module

Publication 1757-IN916C-EN-P - March 2008

Wire the Connector for the Remote I/O Network

Follow these steps to wire the connector.

1. Connect Line 1 of the remote I/O cable to the upper pin.

2. Connect the shield to the middle pin.

3. Connect Line 2 to the lower pin on the 1757-ABRIO.

4. Terminate both ends of a remote I/O network by using external

resistors attached to the physical ends of the network.

There should be two and terminators on the network.

Select Proper Resistor

Use 82 ohm resistors if the network operates at 230.4 kbps or if the network

operates at 57.6 kbps or 115.2 kbps and none of the devices in the table below

are present. The maximum number of devices on the network is 32.

Use 150 ohm resistors if the network contains any of the devices in the table

below, or if the network operates at 57.6 kbps or 115.2 kbps and you do not

require the network to support more than 16 devices.

Device Type Catalog Number Series

Adapters 1771-AS All

1771-ASB

1771-DCM

Miscellaneous 1771-AF

Process Remote I/O (RIO) Communication Interface Module 9

Publication 1757-IN916C-EN-P - March 2008

Removing or Replacing the Module

If you are replacing an existing module with an identical one, and you want to

resume identical system operation, you must:

•install the new module in the same slot.

•run the configuration program and download the appropriate

configuration to the module.

Apply Chassis Power

Turn the rack power supply on.

Check Power Supply and Module Status

The rack power supply indicator should be green. The module OK status

indicator should be solid red immediately after you turn on the rack power

supply and then it turns solid green. Refer to the installation instructions for

your particular 1756 rack power supply for recommended actions for

checking your power supply.

Status Display Power-up Messages

The alphanumeric display shows the following messages at power-up.

If the indicator on the 1757-ABRIO module does not cycle through these

messages on powerup, refer to the Troubleshooting section of publication

1757-UM007C, the 1757-ABRIO User Manual.

B#nn Stages in the start-up processes, nn is a hexadecimal number

Boot Next stage in power-up sequence

57ABRIO Ver x.xx.xx Module firmware version

10 Process Remote I/O (RIO) Communication Interface Module

Publication 1757-IN916C-EN-P - March 2008

Power Supply Indicator

Interpret the Alphanumeric Display

The Process Remote I/O (RIO) Communication Interface Module displays

alphanumeric messages that provide diagnostic information about your

module. The warning messages display twice, then the normal display

resumes. The following table summarizes the messages.

Alphanumeric Display Message Descriptions

POWER Indicator Power Supply Status Recommended Action

Off Not operating •Turn power switch ON.

•Check power wiring

connections.

•Check fuse.

On Operating None, normal operation.

Message Description

57ABRIO

Version x.xx.xx

The module’s firmware version, displayed at powerup. The three parts of

the version number are the major revision, the minor revision and the

build number.

Config The module is being configured from the configuration program.

Inactive The module is not receiving any messages that read or write tags. It is

scanning discrete I/O in program mode. Block transfers are not updating.

Active The module is receiving messages that read or write tags. It is scanning

discrete I/O in run mode. Block transfers are updating.

Forced Active The module has been put into active mode by the configuration program.

RIO Flash

Config Invalid The configuration stored in Flash memory on the module is invalid due to

the following possible reasons.

•The module has never been configured.

•The module firmware has been updated and the configuration

format has changed.

•A fatal error has been captured.

To clear the invalid state, download the I/O configuration.

Andere Handbücher für 1757-ABRIO

Inhaltsverzeichnis

Andere Allen-Bradley Steuereinheit Handbücher

Allen-Bradley

Allen-Bradley Compact 5000 Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-VHSC5 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-OX8I Bedienungsanleitung

Allen-Bradley

Allen-Bradley Series B Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX Ex 1797-OE8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Series B Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756 ControlLogix Bedienungsanleitung

Allen-Bradley

Allen-Bradley 857-VPA3CG Bedienungsanleitung

Allen-Bradley

Allen-Bradley C Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley CAB6-HA 3 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 BASIC Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-OA8K Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1770-KFDG Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-VHSC Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-16CFGM12M12LDR Bedienungsanleitung

Allen-Bradley

Allen-Bradley DeviceNet 1747-SDN Bedienungsanleitung

Allen-Bradley

Allen-Bradley Entek XM-123 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-OB16 Bedienungsanleitung

Allen-Bradley

Allen-Bradley MSR41 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-IL Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-DH485 Bedienungsanleitung

Allen-Bradley

Allen-Bradley OptiSIS 1711-P05SISID050S Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1791-16BC Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1492-AIFM16-F-5 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung