Allen-Bradley POINT I/O series Bedienungsanleitung

Installation Instructions

POINT I/O 2 and 4 Relay Output Modules

Catalog numbers 1734-OW2, 1734-OW4, Series C

Table of Contents

Topic Page

Important User Information 2

Environment and Enclosure 3

Preventing Electrostatic Discharge 3

North American Hazardous Location Approval 4

European Hazardous Location Approval 5

About the Module 6

Mount the I/O Base 8

Install the Module 9

Install the Removable Terminal Block 12

Remove a Mounting Base 14

Communicate with Your Module 14

Wire the Module 15

Interpret Status Indicators 19

Specifications 21

2POINT I/O 2 and 4 Relay Output Modules

Publication 1734-IN055H-EN-E - August 2016

Important User Information

Solid-state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls

(Publication SGI-1.1 available from your local Rockwell Automation sales office or online at

http://www.rockwellautomation.com/literature/) describes some important differences between

solid-state equipment and hard-wired electromechanical devices. Because of this difference, and also

because of the wide variety of uses for solid-state equipment, all persons responsible for applying this

equipment must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular installation, Rockwell Automation, Inc.

cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING: Identifies information about practices or circumstances that can cause an

explosion in a hazardous environment, which may lead to personal injury or death,

property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to

personal injury or death, property damage, or economic loss. Attentions help you

identify a hazard, avoid a hazard and recognize the consequences.

SHOCK HAZARD: Labels may be on or inside the equipment (for example, drive or

motor) to alert people that dangerous voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment (for example, drive or

motor) to alert people that surfaces may reach dangerous temperatures.

IMPORTANT

Identifies information that is critical for successful application and understanding of

the product.

POINT I/O 2 and 4 Relay Output Modules 3

Publication 1734-IN055H-EN-E - August 2016

Environment and Enclosure

Preventing Electrostatic Discharge

ATTENTION: This equipment is intended for use in a Pollution Degree 2

industrial environment, in overvoltage Category II applications (as defined in IEC

60664-1), at altitudes up to 2000 m (6562 ft) without derating.

This equipment is considered Group 1, Class A industrial equipment according

to IEC/CISPR 11. Without appropriate precautions, there may be difficulties

with electromagnetic compatibility in residential and other environments due to

conducted and radiated disturbances.

This equipment is supplied as open-type equipment. It must be mounted within

an enclosure that is suitably designed for those specific environmental

conditions that will be present and appropriately designed to prevent personal

injury resulting from accessibility to live parts. The enclosure must have

suitable flame-retardant properties to prevent or minimize the spread of flame,

complying with a flame spread rating of 5VA or be approved for the application

if nonmetallic. The interior of the enclosure must be accessible only by the use

of a tool. Subsequent sections of this publication may contain additional

information regarding specific enclosure type ratings that are required to

comply with certain product safety certifications.

In addition to this publication, see the following:

• Industrial Automation Wiring and Grounding Guidelines, publication

1770-4.1, for additional installation requirements.

• NEMA Standard 250 and IEC 60529, as applicable, for explanations of the

degrees of protection provided by enclosures.

ATTENTION: This equipment is sensitive to electrostatic discharge, which can

cause internal damage and affect normal operation. Follow these guidelines

when you handle this equipment:

• Touch a grounded object to discharge potential static.

• Wear an approved grounding wrist strap.

• Do not touch connectors or pins on component boards.

• Do not touch circuit components inside the equipment.

• Use a static-safe workstation, if available.

• Store the equipment in appropriate static-safe packaging when not in use.

4POINT I/O 2 and 4 Relay Output Modules

Publication 1734-IN055H-EN-E - August 2016

North American Hazardous Location Approval

The following information applies when

operating this equipment in hazardous

locations:

Informations sur l’utilisation de cet équipement

en environnements dangereux:

Products marked “CL I, DIV 2, GP A, B, C, D” are

suitable for use in Class I Division 2 Groups A, B,

C, D, Hazardous Locations and nonhazardous

locations only. Each product is supplied with

markings on the rating nameplate indicating the

hazardous location temperature code. When

combining products within a system, the most

adverse temperature code (lowest “T” number)

may be used to help determine the overall

temperature code of the system. Combinations

of equipment in your system are subject to

investigation by the local Authority Having

Jurisdiction at the time of installation.

Les produits marqués “CL I, DIV 2, GP A, B, C, D” ne

conviennent qu'à une utilisation en environnements de

Classe I Division 2 Groupes A, B, C, D dangereux et non

dangereux. Chaque produit est livré avec des

marquages sur sa plaque d'identification qui indiquent

le code de température pour les environnements

dangereux. Lorsque plusieurs produits sont combinés

dans un système, le code de température le plus

défavorable (code de température le plus faible) peut

être utilisé pour déterminer le code de température

global du système. Les combinaisons d'équipements

dans le système sont sujettes à inspection par les

autorités locales qualifiées au moment de

l'installation.

EXPLOSION HAZARD

•Do not disconnect equipment

unless power has been removed

or the area is known to be

nonhazardous.

•Do not disconnect connections to

this equipment unless power has

been removed or the area is

known to be nonhazardous.

Secure any external connections

that mate to this equipment by

using screws, sliding latches,

threaded connectors, or other

means provided with this product.

•Substitution of components may

impair suitability for Class I,

Division 2.

•If this product contains batteries,

they must only be changed in an

area known to be nonhazardous.

RISQUE D’EXPLOSION

•Couper le courant ou s'assurer que

l'environnement est classé non

dangereux avant de débrancher

l'équipement.

•Couper le courant ou s'assurer que

l'environnement est classé non

dangereux avant de débrancher les

connecteurs. Fixer tous les

connecteurs externes reliés à cet

équipement à l'aide de vis, loquets

coulissants, connecteurs filetés ou

autres moyens fournis avec ce produit.

•La substitution de composants peut

rendre cet équipement inadapté à une

utilisation en environnement de

Classe I, Division 2.

•S'assurer que l'environnement est

classé non dangereux avant de

changer les piles.

WARNING: Exposure to some chemicals may degrade the sealing properties of

materials used in the following devices:

Relay K2 and K4, Epoxy for 1734-OW2, and Relay K1 through K4, Epoxy

for 1734-OW4.

It is recommended that the User periodically inspect these devices for any

degradation of properties and replace the module if degradation is found.

POINT I/O 2 and 4 Relay Output Modules 5

Publication 1734-IN055H-EN-E - August 2016

European Hazardous Location Approval

The following applies when the product bears the Ex Marking

This equipment is intended for use in potentially explosive atmospheres as defined by

European Union Directive 94/9/EC.

DEMKO certifies that this equipment has been found to comply with the Essential Health

and Safety Requirements relating to the design and construction of Category 3 equipment

intended for use in Zone 2 potentially explosive atmospheres, given in Annex II to this

Directive.

Compliance with the Essential Health and Safety Requirements has been assured by

compliance with EN 60079-0:2012+A11:2013, EN 60079-15:2010, reference certificate

number DEMKO 04ATEX0330347X.

WARNING: This equipment shall be mounted in an ATEX certified enclosure

with a minimum ingress protection rating of at least IP54 (as defined in

IEC60529) and used in an environment of not more than Pollution Degree 2 (as

defined in IEC 60664-1) when applied in Zone 2 environments. The enclosure

must utilize a tool removable cover or door.

WARNING: This equipment shall be used within its specified ratings defined

by Rockwell Automation.

WARNING: Provision shall be made to prevent the rated voltage from being

exceeded by transient disturbances of more than 140% of the rated voltage

when applied in Zone 2 environments.

WARNING: This equipment must be used only with ATEX certified Rockwell

Automation backplanes.

WARNING: Secure any external connections that mate to this equipment by

using screws, sliding latches, threaded connectors, or other means provided

with this product.

WARNING: Do not disconnect equipment unless power has been removed or

the area is known to be nonhazardous.

WARNING: The Maximum Continuous Operating Temperature of the relay seal

is 135 °C. It is recommended that the User periodically inspect these devices for

any degradation of properties and replace the module if degradation is found.

ATTENTION: This equipment is not resistant to sunlight or other sources of

UV radiation.

6POINT I/O 2 and 4 Relay Output Modules

Publication 1734-IN055H-EN-E - August 2016

About the Module

These POINT I/O™ 2 and 4 Relay Output Modules, 1734-OW2, 1734-OW4, Series C

products can be used with DeviceNet and PROFIBUS adapters. They can be used with

ControlNet and Ethernet adapters using RSLogix 5000, version 11 or later.

See the figures to familiarize yourself with major parts of the modules. The wiring base

assembly consists of a mounting base, 1734-MB, and removable terminal block, 1734-RTB

or 1734-RTBS, and 1734-TOP or 1734-TOPS one-piece terminal base.

Modules Mounted on Removable Terminal Block and Mounting Base

Description Description

1 Module locking mechanism 6 Mounting base

2 Slide-in writable label 7 Interlocking side pieces

3 Insertable I/O module 8 Mechanical keying

4 Removable Terminal Block handle 9 DIN rail locking screw (orange)

5 Removable Terminal Block (RTB) 10 Module wiring diagram

Module

Status

Network

Status

45720

POINT I/O 2 and 4 Relay Output Modules 7

Publication 1734-IN055H-EN-E - August 2016

Modules Mounted on 1734-TOP or 1734-TOPS One-piece Terminal Base

Description Description

1 Module locking mechanism 5 Interlocking side pieces

2 Slide-in writable label 6 Mechanical keying

3 Handle 7 DIN rail locking screw (orange)

4 1734-TOP or 1734-TOPS one-piece terminal

base with screw or spring clamp 8 Module wiring diagram

45712

8POINT I/O 2 and 4 Relay Output Modules

Publication 1734-IN055H-EN-E - August 2016

Mount the I/O Base

To mount the I/O base on the DIN rail (Allen-Bradley part number 199-DR1; 46277-3;

EN50022), proceed as follows:

1. Position the mounting base vertically above the installed units (adapter, power

supply or existing module).

2. Slide the mounting base down allowing the interlocking side pieces to engage the

adjacent module or adapter.

3. Press firmly to seat the mounting base on the DIN rail. The mounting base snaps

into place.

ATTENTION: This product is grounded through the DIN rail to chassis ground.

Use zinc plated yellow-chromate steel DIN rail to assure proper grounding. The

use of other DIN rail materials (for example, aluminum or plastic) that can

corrode, oxidize, or are poor conductors, can result in improper or intermittent

grounding. Secure DIN rail to mounting surface approximately every 200 mm

(7.8 in.) and use end-anchors appropriately.

31586

POINT I/O 2 and 4 Relay Output Modules 9

Publication 1734-IN055H-EN-E - August 2016

Install the Module

The module can be installed before or after base installation. Make sure that the mounting

base is correctly keyed before installing the module into the mounting base. In addition,

make sure the mounting base locking screw is positioned horizontal in reference to

the base.

1. Using a bladed screwdriver to rotate the keyswitch on the mounting base

clockwise until the number required for the type of module being installed aligns

with the notch in the base.

2. Make certain the DIN rail locking screw is in the horizontal position.

You cannot insert the module if the locking mechanism is unlocked.

WARNING: When you insert or remove the module while backplane power is

on, an electrical arc can occur. This could cause an explosion in hazardous

location installations.

Be sure that power is removed or the area is nonhazardous before proceeding.

Repeated electrical arcing causes excessive wear to contacts on both the

module and its mating connector. Worn contacts may create electrical

resistance that can affect module operation.

10 POINT I/O 2 and 4 Relay Output Modules

Publication 1734-IN055H-EN-E - August 2016

3. Insert the module straight down into the mounting base and press to secure.

The module locks into place.

Turn the keyswitch to align the

number with the notch.

Notch position 3 is shown.

Make sure the DIN rail locking

screw is in the horizontal position.

1734-TB Base

45696

Inhaltsverzeichnis

Andere Allen-Bradley Steuereinheit Handbücher

Allen-Bradley

Allen-Bradley 1771-OW Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1492-CM1771-LD008F Bedienungsanleitung

Allen-Bradley

Allen-Bradley OptiSIS 1711-P05SISID050S Bedienungsanleitung

Allen-Bradley

Allen-Bradley CAB6-HA 2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX Ex 1797-OE8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1734-IB8S Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-OA8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1757-ABRIO Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756-M02AS Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-KA2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-DMD30 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1606-XLS960BUFFER Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorPoint A Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1762-OF4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley XM-124 Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O 1794-ID2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1769-SDN Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 750 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-OD Installations- und Benutzerhandbuch

Allen-Bradley

Allen-Bradley 1756-EN2TSC Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-ADN Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IE8H Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-DHRIO Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-ENET/B Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung