Allen-Bradley Micrologix 1500 Bedienungsanleitung

Publication 1764-IN001A-ML-P

Installation Instructions

MicroLogix™ 1500 Programmable

Controller Base Units

(Catalog Numbers 1764-24AWA, 1764-24BWA, and

1764-28BXB)

Inside...

English Section ....................................................................................... 3

Français................................................................................................. 21

Deutscher Abschnitt ............................................................................. 41

Sezione in Italiano ................................................................................ 61

Sección en español............................................................................... 81

Seção em Português........................................................................... 101

Allen-Bradley Parts

2MicroLogix™ 1500 Programmable Controller Base Units

Publication 1764-IN001A-ML-P

Installation Instructions

English Section

MicroLogix™ 1500 Programmable

Controller Base Units

(Catalog Numbers 1764-24AWA, 1764-24BWA, and

1764-28BXB)

Inside...

For More Information.............................................................................. 4

Overview ................................................................................................. 5

Base Unit Description ............................................................................. 6

Hazardous Location Considerations ....................................................... 7

Mounting the Controller ......................................................................... 8

Wiring the Controller ............................................................................ 12

Specifications ....................................................................................... 16

Allen-Bradley Parts

4MicroLogix™ 1500 Programmable Controller Base Units

Publication 1764-IN001A-ML-P

For More Information

If you would like a manual, you can:

• download a free electronic version from the internet:

www.ab.com/micrologix or www.theautomationbookstore.com

• purchase a printed manual by:

– contacting your local distributor or Rockwell Automation representative

– visiting www.theautomationbookstore.com and placing your order

–calling1.800.963.9548 (USA/Canada)

or 001.330.725.1574 (Outside USA/Canada)

Table 1 Related Publications

For Refer to this Document Pub. No.

A more detailed description of how to

install and use your MicroLogix 1500

programmable controller.

MicroLogix 1500

Programmable Controllers User

Manual

1764-UM001A-US-P

A reference manual that contains data and

functin files, instruction set, and

troubleshooting information for

MicroLogix 1200 and MicroLogix 1500.

MicroLogix 1200 and

MicroLogix 1500 Instruction

Set Reference Manual

1762-RM001B-US-P

More information on proper wiring and

grounding techniques. Industrial Automation Wiring

and Grounding Guidelines 1770-4.1

MicroLogix™ 1500 Programmable Controller Base Units 5

Publication 1764-IN001A-ML-P

Overview

Install your controller using these installation instructions.

ATTENTION Do not remove protective debris strips until after the base and

all other equipment in the panel near the base is mounted and

wiring is complete. Once wiring is complete, remove

protective debris strips and install processor unit. Failure to

remove strips before operating can cause overheating.

ATTENTION Be careful of metal chips when drilling mounting holes for

your controller or other equipment within the enclosure or

panel. Drilled fragments that fall into the controller could

cause damage. Do not drill holes above a mounted controller if

the protective debris strips have been removed.

ATTENTION Electrostatic discharge can damage semiconductor devices

inside the base unit. Do not touch the connector pins or other

sensitive areas.

Protective Debris

Strips

ESD Sticker

Allen-Bradley Parts

6MicroLogix™ 1500 Programmable Controller Base Units

Publication 1764-IN001A-ML-P

Base Unit Description

Table 2 Standard Base Units

Catalog Number Base Unit I/O and Power Supply

1764-24AWA 120V ac inputs/ relay outputs/ 120/240V ac power supply

1764-24BWA 24V dc inputs/ relay outputs/ 120/240V ac power supply

1764-28BXB 24V dc inputs/ FET and relay outputs/ 24V dc power supply

Table 3 Base Unit Description

Feature Description

1 Removable Terminal Blocks

2 Interface to Expansion I/O, Removable ESD Sticker

3 Input LEDs

4 Output LEDs

5 RS-232 Communication Port (CH0)

6 Status LEDs

7 Terminal Doors and Label

MicroLogix™ 1500 Programmable Controller Base Units 7

Publication 1764-IN001A-ML-P

Hazardous Location Considerations

This equipment is suitable for use in Class I,Division 2, Groups A, B, C, D or

non-hazardous locations only. The following WARNING statement applies to

use in hazardous locations.

Use only the following communication cables in Class I, Division 2 hazardous

locations.

WARNING EXPLOSION HAZARD

• Substitution of components may impair suitability for Class

I, Division 2.

• Do not replace components or disconnect equipment unless

power has been switched off or the area is known to be

non-hazardous.

• Do not connect or disconnect components unless power has

been switched off or the area is known to be non-hazardous.

• This product must be installed in an enclosure. All cables

connected to the product must remain in the enclosure or be

protected by conduit or other means.

• All wiring must comply with N.E.C. article 501-4(b).

Table 4 Cable Listing

Environment Classification Communication Cables

Class I, Division 2 Hazardous Environment 1761-CBL-PM02 Series C or later

1761-CBL-HM02 Series C or later

1761-CBL-AM00 Series C or later

1761-CBL-AP00 Series C or later

2707-NC8 Series B or later

2707-NC10 Series B or later

2707-NC11 Series B or later

Allen-Bradley Parts

8MicroLogix™ 1500 Programmable Controller Base Units

Publication 1764-IN001A-ML-P

Mounting the Controller

General Considerations

Most applications require installation in an industrial enclosure (Pollution Degree

2) to reduce the effects of electrical interference (Over Voltage Category II) and

environmental exposure. Locate your controller as far as possible from power

lines, load lines, and other sources of electrical noise such as hard-contact

switches, relays, and AC motor drives. For more information on proper

grounding guidelines, see the Industrial Automation Wiring and Grounding

Guidelines publication 1770-4.1.

ATTENTION

Vertical mounting is not recommended due to heat build-up

considerations.

ATTENTION Be careful of metal chips when drilling mounting holes for

your controller or other equipment within the enclosure or

panel. Drilled fragments that fall into the base or processor unit

could cause damage. Do not drill holes above a mounted

controller if the protective debris strips have been removed or

the processor has been installed.

NOTE Remove the ESD sticker to install expansion I/O modules. An

end cap terminator (catalog numbers 1769-ECR or -ECL) or

an extension cable (catalog numbers 1769-CRR1, -CRR3,

-CLL1, -CLL3, -CRL1, -CRL3) must be used at the end of the

group of I/O modules attached to the MicroLogix 1500

Controller. The end cap terminator is not provided with the

base unit. A maximum of eight I/O modules may be connected

to the base.

MicroLogix™ 1500 Programmable Controller Base Units 9

Publication 1764-IN001A-ML-P

Mounting Dimensions

Controller Spacing

The base unit is designed to be mounted horizontally, with the Compact™

expansion I/O extending to the right of the base unit. Allow 50 mm (2 in.) of

space on all sides for adequate ventilation, as shown below.

Table 5 Dimensions

Dimension 1764-24AWA 1764-24BWA 1764-28BXB

Height (A) 138 mm (5.43 in.)

Width (B) 168 mm (6.62 in.)

Depth (C) 87 mm (3.43 in.)

Top

Bottom

Side

Allen-Bradley Parts

10 MicroLogix™ 1500 Programmable Controller Base Units

Publication 1764-IN001A-ML-P

Using a DIN Rail

The base unit and expansion I/O DIN rail latches lock intheopen position so that

an entire system can be easily attached to or removed from the DIN rail. The

maximum extension of the latch is 15 mm (0.67 in.) in the open position. A

flat-blade screw driver is required for removal of the base unit. The base can be

mounted to EN50022-35x7.5 or EN50022-35x15 DIN rails. DIN rail mounting

dimensions are shown below.

To install your base unit on the DIN rail:

1. Mount your DIN rail. (Make sure that the placement of the base unit on the

DIN rail meets the recommended spacing requirements, see “Controller

Spacing” on page 9. Refer to the mounting template from the inside back

cover of this document.)

2. Hook the top slot over the DIN rail.

3. While pressing the base unit down against the top of the rail, snap the bottom

of the base unit into position.

4. Leave the protective debris strip attached until you are finished wiring the base

unit and any other devices.

Table 6 DIN Rail Mounting Dimensions

Dimension Height

A 138 mm (5.43 in.)

B 47.6 mm (1.875 in.)

C 47.6 mm (1.875 in) DIN latch closed

54.7 mm (2.16 in.) DIN latch open

Andere Handbücher für micrologix 1500

Inhaltsverzeichnis

Sprachen:

Andere Allen-Bradley Controller Handbücher

Allen-Bradley

Allen-Bradley controllogix 1756-L55M12 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Micro830 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 70 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-HYD02 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Pico 1760-L12AWA Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756 ControlLogix Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1100 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1336 IMPACT Bedienungsanleitung

Allen-Bradley

Allen-Bradley 160 SSC Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1305 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley FlexLogix 1794-L33 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 70 Bedienungsanleitung

Allen-Bradley

Allen-Bradley powerflex 700 Bedienungsanleitung

Allen-Bradley

Allen-Bradley controllogix 1756-L61 Betriebsanleitung

Allen-Bradley

Allen-Bradley GuardPLC 1753 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1747-PBASE Betriebsanleitung

Allen-Bradley

Allen-Bradley powerflex 700 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Logix5000 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley micrologix 1500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Compact GuardLogix 5370 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 70 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung