Allen-Bradley PowerFlex 4 Bedienungsanleitung

Quick Start

PowerFlex 4 Adjustable

Frequency AC Drive

FRN 2.xx

This Quick Start guide summarizes the basic steps needed to install,

start-up and program the PowerFlex 4 Adjustable Frequency AC Drive.

The information provided Does Not replace the User Manual and is

intended for qualiﬁed drive service personnel only.

For detailed PowerFlex 4 information including EMC instructions,

application considerations and related precautions refer to the

PowerFlex 4

User Manual

, Publication 22A-UM001x on the CD

supplied with the drive or at

www.ab.com/manuals/dr.

General Precautions

ATTENTION:

The drive contains high voltage capacitors which take

time to discharge after removal of mains supply. Before working on

drive, ensure isolation of mains supply from line inputs [R, S, T (L1,

L2, L3)]. Wait three minutes for capacitors to discharge to safe voltage

levels. Failure to do so may result in personal injury or death.

Darkened display LEDs is not an indication that capacitors have

discharged to safe voltage levels.

ATTENTION:

Equipment damage and/or personal injury may result

if this parameter (A092 [Auto Rstrt Tries], A094 [Start At PowerUp]) is

used in an inappropriate application. Do not use this function without

considering applicable local, national and international codes,

standards, regulations or industry guidelines.

ATTENTION:

Only qualiﬁed personnel familiar with adjustable

frequency AC drives and associated machinery should plan or

implement the installation, start-up and subsequent maintenance of the

system. Failure to comply may result in personal injury and/or

equipment damage.

ATTENTION:

This drive contains ESD (Electrostatic Discharge)

sensitive parts and assemblies. Static control precautions are required

when installing, testing, servicing or repairing this assembly.

Component damage may result if ESD control procedures are not

followed. If you are not familiar with static control procedures,

reference A-B publication 8000-4.5.2, “Guarding Against Electrostatic

Damage” or any other applicable ESD protection handbook.

ATTENTION:

An incorrectly applied or installed drive can result in

component damage or a reduction in product life. Wiring or application

errors, such as, undersizing the motor, incorrect or inadequate AC

supply, or excessive ambient temperatures may result in malfunction of

the system.

Allen-Bradley Drives

English-2

•

Mount the drive upright on a ﬂat, vertical and level surface.

–

Install on 35 mm DIN Rail.

–

Install with screws.

•

Protect the cooling fan by avoiding dust or metallic particles.

•

Do not expose to a corrosive atmosphere.

•

Protect from moisture and direct sunlight.

Minimum Mounting Clearances

Ambient Operating Temperatures

Refer to the PowerFlex 4

User Manual

on the CD supplied with the

drive for details on how to comply with the Low Voltage (LV) and

Electromagnetic Compatibility (EMC) Directives.

Mounting Considerations

Minimum Panel Thickness Screw Size Mounting Torque

1.9 mm (0.0747 in.) m4 x 0.7 (#8-32) 1.56-1.96 Nm (14-17 lb.-in.)

Ambient Temperature Enclosure Rating Minimum Mounting

Clearances

Minimum Maximum

-10°C (14°F) 40°C (104°F) IP 20/Open Type Use Mounting Option A

IP 30/NEMA 1/UL Type 1

(1)

Rating requires installation of the PowerFlex 4 IP 30/NEMA 1/UL Type 1 option kit.

Use Mounting Option B

50°C (122°F) IP 20/Open Type Use Mounting Option B

25 mm

(1.0 in.)

120 mm

(4.7 in.)

120 mm

(4.7 in.)

120 mm

(4.7 in.)

120 mm

(4.7 in.)

Mounting Option A

No clearance required

between drives.

Mounting Option B

See page 12 for mounting dimensions.

General Grounding Requirements

U/T1

V/T2

W/T3

R/L1

S/L2

T/L3

SHLD

Important: Remove the MOV to ground jumper if the

drive is installed on an ungrounded distribution system.

Tighten screw after jumper removal.

Jumper

Location

CE Conformity

English-3

Speciﬁcations, Fuses and Circuit Breakers

Drive Ratings

Catalog

Number

Output Ratings Input Ratings Branch Circuit Protection Power

Dissipation

kW (HP) Amps

Voltage

Range kVA Amps Fuses

140M Motor

Protectors Contactors

IP20 Open

Watts

100 - 115V AC 1-Phase Input, 0 - 230V 3-Phase Output

22A-V1P5N104 0.2 (0.25) 1.5 90-126 0.75 6.0 10 140M-C2E-C10 100-C09 25

22A-V2P3N104 0.37 (0.5) 2.3 90-126 1.15 9.0 15 140M-C2E-C16 100-C12 30

22A-V4P5N104 0.75 (1.0) 4.5 90-126 2.25 18.0 30 140M-D8E-C20 100-C23 50

200 - 240V AC – 1-Phase

(1)

Input, 0 - 230V 3-Phase Output

22A-A1P5N104 0.2 (0.25) 1.5 180-265 0.75 5.0 10 140M-C2E-B63 100-C09 25

22A-A2P3N104 0.37 (0.5) 2.3 180-265 1.15 6.0 10 140M-C2E-B63 100-C09 30

22A-A4P5N104 0.75 (1.0) 4.5 180-265 2.25 10.0 15 140M-C2E-C16 100-C12 50

22A-A8P0N104 1.5 (2.0) 8.0 180-265 4.0 18.0 30 140M-D8E-C20 100-C23 80

200 - 240V AC – 3-Phase Input, 0 - 230V 3-Phase Output

22A-B1P5N104 0.2 (0.25) 1.5 180-265 0.75 1.8 3 140M-C2E-B25 100-C09 25

22A-B2P3N104 0.37 (0.5) 2.3 180-265 1.15 2.5 6 140M-C2E-B40 100-C09 30

22A-B4P5N104 0.75 (1.0) 4.5 180-265 2.25 5.2 10 140M-C2E-C10 100-C09 50

22A-B8P0N104 1.5 (2.0) 8.0 180-265 4.0 9.5 15 140M-C2E-C16 100-C12 80

22A-B012N104 2.2 (3.0) 12.0 180-265 5.5 15.5 25 140M-C2E-C16 100-C16 115

22A-B017N104 3.7 (5.0) 17.5 180-265 8.6 21.0 35 140M-F8E-C25 100-C23 165

380 - 480V AC – 3-Phase

Input, 0 - 460V 3-Phase Output

22A-D1P4N104 0.37 (0.5) 1.4 340-528 1.4 1.8 3 140M-C2E-B25 100-C09 30

22A-D2P3N104 0.75 (1.0) 2.3 340-528 2.3 3.2 6 140M-C2E-B40 100-C09 40

22A-D4P0N104 1.5 (2.0) 4.0 340-528 4.0 5.7 10 140M-C2E-B63 100-C09 60

22A-D6P0N104 2.2 (3.0) 6.0 340-528 5.9 7.5 15 140M-C2E-C10 100-C09 90

22A-D8P7N104 3.7 (5.0) 8.7 340-528 8.6 9.0 15 140M-C2E-C16 100-C16 145

Input/Output Ratings Approvals

Output Frequency:

0-240 Hz (Programmable)

Efﬁciency:

97.5% (Typical)

Digital Control Inputs (Input Current = 6mA) Analog Control Inputs

SRC (Source) Mode:

18-24V = ON

0-6V = OFF

SNK (Sink) Mode:

0-6V = ON

18-24V = OFF

4-20mA Analog:

250 ohm input impedance

0-10V DC Analog:

100k ohm input impedance

External Pot:

1-10k ohms, 2 Watt minimum

Control Output

Programmable Output (form C relay)

Resistive Rating: 3.0A at 30V DC, 3.0A at 125V AC, 3.0A at 240V AC

Inductive Rating: 0.5A at 30V DC, 0.5A at 125V AC, 0.5A at 240V AC

Fuses and Circuit Breakers

Recommended Fuse Type:

UL Class J, CC, T or Type BS88; 600V (550V) or equivalent.

Recommended Circuit Breakers:

HMCP circuit breakers or equivalent.

Protective Features

Motor Protection:

t overload protection - 150% for 60 Secs, 200% for 3 Secs (Provides Class 10 protection)

Overcurrent:

200% hardware limit, 300% instantaneous fault

Over Voltage:

100-120V AC Input –Trip occurs at 405V DC bus voltage (equivalent to 150V AC incoming line)

200-240V AC Input –Trip occurs at 405V DC bus voltage (equivalent to 290V AC incoming line)

380-460V AC Input –Trip occurs at 810V DC bus voltage (equivalent to 575V AC incoming line)

Under Voltage:

100-120V AC Input –Trip occurs at 210V DC bus voltage (equivalent to 75V AC incoming line)

200-240V AC Input –Trip occurs at 210V DC bus voltage (equivalent to 150V AC incoming line)

380-480V AC Input –Trip occurs at 390V DC bus voltage (equivalent to 275V AC incoming line)

Control Ride Through:

Minimum ride through is 0.5 Secs - typical value 2 Secs

Faultless Power Ride Through:

100 milliseconds

Dynamic Braking

Internal brake IGBT included with all ratings 0.75 kW (1 HP) and larger. Refer to Appendix B of the PowerFlex 4

User Manual

on CD for ordering information.

(1)

200-240V AC - 1-Phase drives are also available with an integral EMC ﬁlter. Catalog sufﬁx changes from N104 to N114.

UL508C UL

CCSA 22.2

EMC Directive 89/336

LV: EN 50178, EN 60204

EMC: EN 61800-3, EN 50081-1, EN 50082-2

Allen-Bradley Drives

English-4

Power Terminal Block (A Frame Shown)

Power Terminal Block Speciﬁcations

Input Power Conditions

I/O Terminal Block Speciﬁcations

Refer to the PowerFlex 4

User Manual

on CD for maximum power and

control cable length recommendations

Power Wiring

Power Wire Rating Recommended Copper Wire

Unshielded 600V, 75°C (167°F) THHN/THWN 15 Mils insulated, dry location

Shielded 600V, 75°C or 90°C (167°F or 194°F) RHH/RHW-2 Belden 29501-29507 or equivalent

Shielded Tray rated 600V, 75°C or 90°C (167°F or 194°F) RHH/RHW-2 Shawﬂex 2ACD/3ACD or equivalent

V/T2T/L3S/L2R/L1 U/T1 W/T3

BR+ BR-

Terminal Description

R/L1, S/L2 1-Phase Input

R/L1, S/L2, T/L3 3-Phase Input

U/T1 To Motor U/T1

Switch any two motor leads to

change forward direction.

V/T2 To Motor V/T2

W/T3 To Motor W/T3

BR+, BR- Dynamic Brake Resistor Connection [0.75 kW (1 HP) ratings and higher]

Safety Ground - PE

Frame Maximum Wire Size

(1)

Minimum Wire Size

(1)

Torque

A 3.3 mm

(12 AWG) 0.8 mm

(18 AWG)

1.7-2.2 N-m (16-19 lb.-in.)

B 5.3 mm

(10 AWG) 1.3 mm

(16 AWG)

(1)

Maximum/minimum sizes that the terminal block will accept - these are not recommendations.

Input Power Condition Corrective Action

Low Line Impedance (less than 1% line reactance)

•

Install Line Reactor

(2)

•

or Isolation Transformer

Greater than 120 kVA supply transformer

Line has power factor correction capacitors

Line has frequent power interruptions

Line has intermittent noise spikes in excess of 6000V (lightning)

Phase to ground voltage exceeds 125% of normal line to line voltage

•

Remove MOV jumper to ground.

•

and Install Isolation Transformer with

grounded secondary if necessary.

Ungrounded Distribution System

(2)

Refer to Appendix B of the PowerFlex 4

User Manual

on CD for accessory ordering information.

I/O Wiring Recommendations

(3)

Wire Type(s) Description Minimum Insulation Rating

Belden 8760/9460

(or equiv.)

0.8 mm

(18AWG), twisted pair, 100% shield with

drain. 300V

60 degrees C

(140 degrees F)

Belden 8770

(or equiv.)

0.8 mm

(18AWG), 3 conductor, shielded for

remote pot only.

(3)

If the wires are short and contained within a cabinet which has no sensitive circuits, the use of shielded wire may not be

necessary, but is always recommended.

Maximum Wire Size

(4)

Minimum Wire Size

(4)

Torque

1.3 mm

(16 AWG) 0.13 mm

(26 AWG) 0.5-0.8 N-m (4.4-7 lb.-in.)

(4)

Maximum / minimum that the terminal block will accept - these are not recommendations.

English-5

Control Terminal Block

No. Signal Default Description Param.

R1 Relay N.O. Fault Normally open contact for output relay. A055

R2 Relay Common –Common for output relay.

R3 Relay N.C. Fault Normally closed contact for output relay. A055

Sink/Source DIP Switch Source (SRC) Inputs can be wired as Sink (SNK) or Source (SRC) via DIP Switch

setting.

01 Stop

(1)

Coast The factory installed jumper or a normally closed input

must be present for the drive to start. P036

(1)

02 Start/Run FWD Not Active Command comes from the integral keypad by default. To

disable reverse operation, see A095 [Reverse Disable].

P036, P037

03 Direction/Run REV Not Active P036, P037,

A095

04 Digital Common –For digital inputs. Electronically isolated with digital inputs

from analog I/O.

05 Digital Input 1 Preset Frequencies Program with A051 [Digital In1 Sel]. A051

06 Digital Input 2 Preset Frequencies Program with A052 [Digital In2 Sel]. A052

11 +24V DC –Drive supplied power for digital inputs.

Maximum output current is 100mA.

12 +10V DC –Drive supplied power for 0-10V external potentiometer.

Maximum output current is 15mA. P038

13 0-10V In

(3)

Not Active For external 0-10V input supply

(input impedance = 100k ohm) or potentiometer wiper. P038

14 Analog Common –For 0-10V In or 4-20mA In. Electronically isolated with

analog inputs from digital I/O.

15 4-20mA In

(3)

Not Active For external 4-20mA input supply

(input impedance = 250 ohm). P038

16 RS485 (DSI) Shield –Terminal should be connected to safety ground - PE when

using the RS485 (DSI) communications port.

(3)

Only one analog frequency source may be connected at a time. If more than one reference is connected at the same

time, an undetermined frequency reference will result.

Stop (1)

Start/Run FWD (2)

Direction/Run REV

Digital Common

Digital Input 1

Digital Input 2

Relay N.O.

Relay Common

Relay N.C.

+24V DC

+10V DC

0-10V In

Analog Common

4-20mA In

RS485 Shield

+24V

+10V

Typical

SNK Wiring

Typical

SRC Wiring

RS485

(DSI)

R1 R2 R3

01 02 03 04 05 06

11 12 13 14 15 16

SNK

SRC (1)

Potentiometer

must be

1-10k ohm

2 Watt Min.

30V DC 125V AC 240V AC

Resistive 3.0A 3.0A 3.0A

Inductive 0.5A 0.5A 0.5A

(1) Important: I/O Terminal 01 is

always a coast to stop input except

when P036 [Start Source] is set to

“3-Wire”control. In three wire

control, I/O Terminal 01 is controlled

by P037 [Stop Mode]. All other stop

sources are controlled by P037

[Stop Mode].

Important: The drive is shipped with

a jumper installed between I/O

Terminals 01 and 11. Remove this

jumper when using I/O Terminal 01

as a stop input.

(2) Two wire control shown. For three

wire control use a momentary input

on I/O Terminal 02 to

command a start. Use a maintained

input for I/O Terminal 03 to

change direction.

Refer to the PowerFlex 4

User Manual on CD for

detailed I/O wiring examples.

P036

[Start Source] Stop

I/O Terminal 01

Stop

Keypad Per P037 Coast

3-Wire Per P037 Per P037

2-Wire Per P037 Coast

RS485 Port Per P037 Coast

Allen-Bradley Drives

English-6

Before Applying Power to the Drive

❏

Conﬁrm that all inputs are connected to the correct terminals and are

secure.

❏

Verify that AC line power at the disconnect device is within the rated

value of the drive.

❏

Verify that any digital control power is 24 volts.

❏

Verify that the Sink (SNK)/Source (SRC) Setup DIP Switch is set to

match your control wiring scheme. See page 5 for location.

Important:

The default control scheme is Source (SRC). The Stop

terminal is jumpered (I/O Terminals 01 and 11) to allow

starting from the keypad. If the control scheme is changed

to Sink (SNK), the jumper must be removed from I/O

Terminals 01 and 11 and installed between I/O Terminals

01 and 04.

❏

Verify that the Stop input is present or the drive will not start.

Important:

If I/O Terminal 01 is used as a stop input, the jumper

between I/O Terminals 01 and 11 must be removed.

Applying Power to the Drive

❏

Apply AC power and control voltages to the drive.

❏

Familiarize yourself with the integral keypad features (see next page)

before setting any Program Group parameters.

Start, Stop, Direction and Speed Control

Factory default parameter values allow the drive to be controlled from

the integral keypad. No programming is required to start, stop, change

direction and control speed directly from the integral keypad.

Important:

To disable reverse operation, see A095 [Reverse Disable].

If a fault appears on power up, refer to page 11 for an explanation of the

fault code. For complete troubleshooting information, refer to the

PowerFlex 4

User Manual

on the CD supplied with the drive.

Prepare For Drive Start-Up

ATTENTION:

Power must be applied to the drive to perform the

following start-up procedures. Some of the voltages present are at

incoming line potential. To avoid electric shock hazard or damage to

equipment, only qualiﬁed service personnel should perform the

following procedure. Thoroughly read and understand the procedure

before beginning. If an event does not occur while performing this

procedure,

Do Not Proceed

Remove All Power

including user

supplied control voltages. User supplied voltages may exist even when

main AC power is not applied to the drive. Correct the malfunction

before continuing.

English-7

Integral Keypad

No. LED LED State Description

➊

Run/Direction

Status

Steady Red Indicates drive is running and commanded motor direction.

Flashing Red Drive has been commanded to change direction. Indicates

actual motor direction while decelerating to zero.

➋

Alphanumeric

Display

Steady Red Indicates parameter number, parameter value, or fault code.

Flashing Red Single digit ﬂashing indicates that digit can be edited.

All digits ﬂashing indicates a fault condition.

➌

Displayed Units Steady Red Indicates the units of the parameter value being displayed.

➍

Program Status Steady Red Indicates parameter value can be changed.

➎

Fault Status Flashing Red Indicates drive is faulted.

➏

Pot Status Steady Green Indicates potentiometer on Integral Keypad is active.

➐

Start Key Status Steady Green Indicates Start key on Integral Keypad is active.

The Reverse key is also active unless disabled by A095

[Reverse Disable].

No. Key Name Description

➑

Escape Back one step in programming menu.

Cancel a change to a parameter value and exit Program

Mode.

Select Advance one step in programming menu.

Select a digit when viewing parameter value.

Up Arrow

Down Arrow

Scroll through groups and parameters.

Increase/decrease the value of a ﬂashing digit.

Enter Advance one step in programming menu.

Save a change to a parameter value.

➒Potentiometer Used to control speed of drive. Default is active.

Controlled by parameter P038.

Start Used to start the drive. Default is active.

Controlled by parameter P036.

Reverse Used to reverse direction of the drive. Default is active.

Controlled by parameters P036 and A095.

Stop Used to stop the drive or clear a fault.

This key is always active.

Controlled by parameter P037.

FAU LT

VOLTS

AMPS

HERTZ

RUN

FWD

REV

PROGRAM

➊➋

➍

➏

➒

➎

Menu Description

Display Group (View Only)

Consists of commonly viewed drive operating

conditions.

Basic Program Group

Consists of most commonly used

programmable functions.

Advanced Program Group

Consists of remaining programmable functions.

Fault Designator

Consists of list of codes for speciﬁc fault

conditions. Displayed only when fault is present.

➌

➑

➐

Allen-Bradley Drives

English-8

The last user-selected Display Group parameter is saved when power is removed and is

displayed by default when power is reapplied.

The following is an example of basic integral keypad and display functions. This example

provides basic navigation instructions and illustrates how to program the ﬁrst Program

Group parameter.

Viewing and Editing Parameters

Step Key(s) Example Displays

1. When power is applied, the last user-selected

Display Group parameter number is brieﬂy

displayed with ﬂashing characters. The display

then defaults to that parameter’s current value.

(Example shows the value of d001 [Output

Freq] with the drive stopped.)

2. Press Esc once to display the Display Group

parameter number shown on power-up. The

parameter number will ﬂash.

3. Press Esc again to enter the group menu. The

group menu letter will ﬂash.

4. Press the Up Arrow or Down Arrow to scroll

through the group menu (d, P and A).

5. Press Enter or Sel to enter a group. The right

digit of the last viewed parameter in that group

will ﬂash.

6. Press the Up Arrow or Down Arrow to scroll

through the parameters that are in the group.

7. Press Enter or Sel to view the value of a

parameter. If you do not want to edit the value,

press Esc to return to the parameter number.

8. Press Enter or Sel to enter program mode to

edit the parameter value. The right digit will

ﬂash and the Program LED will illuminate if the

parameter can be edited.

9. Press the Up Arrow or Down Arrow to change

the parameter value. If desired, press Sel to

move from digit to digit or bit to bit. The digit or

bit that you can change will ﬂash.

10. Press Esc to cancel a change. The digit will

stop ﬂashing, the previous value is restored and

the Program LED will turn off.

Press Enter to save a change.The digit will stop

ﬂashing and the Program LED will turn off.

11. Press Esc to return to the parameter list.

Continue to press Esc to back out of the

programming menu.

If pressing Esc does not change the display,

then d001 [Output Frequency] is displayed.

Press Enter or Sel to enter the group menu.

VOLTS

AMPS

HERTZ

FAU LTPROGRAM

VOLTS

AMPS

HERTZ

FAU LTPROGRAM

VOLTS

AMPS

HERTZ

FAU LTPROGRAM

VOLTS

AMPS

HERTZ

FAU LTPROGRAM

VOLTS

AMPS

HERTZ

FAU LTPROGRAM

VOLTS

AMPS

HERTZ

FAU LTPROGRAM

VOLTS

AMPS

HERTZ

FAU LTPROGRAM

VOLTS

AMPS

HERTZ

FAU LTPROGRAM

English-9

The PowerFlex 4 is designed so that start up is simple and efﬁcient. The Program Group

contains the most commonly used parameters.

Smart Start-Up with Basic Program Group Parameters

= Stop drive before changing this parameter.

No. Parameter Min/Max Display/Options Default

P031 [Motor NP Volts] 20/Drive Rated Volts 1 VAC Based on Drive Rating

Set to the motor nameplate rated volts.

P032 [Motor NP Hertz] 10/240 Hz 1 Hz 60 Hz

Set to the motor nameplate rated frequency.

P033 [Motor OL Current] 0.0/(Drive Rated Amps×2) 0.1 Amps Based on Drive Rating

Set to the maximum allowable motor current.

P034 [Minimum Freq] 0.0/240.0 Hz 0.1 Hz 0.0 Hz

Sets the lowest frequency the drive will output

continuously.

P035 [Maximum Freq] 0/240 Hz 1 Hz 60 Hz

Sets the highest frequency the drive will output.

P036 [Start Source] 0/5 0 = “Keypad”(1)

1 = “3-Wire”

2 = “2-Wire”

3 = “2-Wire Level Sensitive”

4 = “2-Wire High Speed”

5 = “RS485 (DSI) Port”

Sets the control scheme used to start the drive.

(1) When active, the Reverse key is also active

unless disabled by A095 [Reverse Disable].

P037 [Stop Mode] 0/7 0 = “Ramp, Clear Fault”(1)

1 = “Coast, Clear Fault”(1)

2 = “DC Brake, Clear Fault”(1)

3 = “DC Brake w/Shutoff, Clear Fault”(1)

4 = “Ramp”

5 = “Coast”

6 = “DC Brake”

7 = “DC Brake w/Shutoff”

Active stop mode for all stop sources [e.g. keypad,

run forward (I/O Terminal 02), run reverse (I/O

Terminal 03), RS485 port] except as noted below.

Important: I/O Terminal 01 is always a coast to

stop input except when P036 [Start Source] is set

for “3-Wire”control. When in three wire control, I/O

Terminal 01 is controlled by P037 [Stop Mode].

(1) Stop input also clears active fault.

P038 [Speed Reference] 0/5 0 = “Drive Potentiometer”

1 = “Internal Freq”

2 = “0-10V Input/Remote Potentiometer”

3 = “4-20mA Input”

4 = “Preset Freq 0-3”

5 = “RS485 (DSI) Port”

Sets the source of the speed reference to the

drive.

Important: When A051 or A052 [Digital Inx Sel] is

set to option 2, 4, 5 or 6, and the digital input is

active, A051 or A052 will override the speed

reference commanded by this parameter. Refer to

Chapter 1 of the PowerFlex 4 User Manual on CD

for details.

P039 [Accel Time 1] 0.0/600.0 Secs 0.1 Secs 10.0 Secs

Sets the rate of accel for all speed increases.

P040 [Decel Time 1] 0.1/600.0 Secs 0.1 Secs 10.0 Secs

Sets the rate of decel for all speed decreases.

P041 [Reset To Defaults] 0/1 0 = “Idle State”

1 = “Reset Defaults”

Resets all parameter values to factory defaults.

Advanced Group Parameters

No. Parameter Min/Max Display/Options Default

A051

A052

[Digital In1 Sel]

I/O Terminal 05

[Digital In2 Sel]

I/O Terminal 06

0/7 0 = “Not Used”

1 = “Accel 2 & Decel 2”

2 = “Jog”

3 = “Auxiliary Fault”

4 = “Preset Frequencies”

5 = “Local”

6 = “RS485 (DSI) Port”

7 = “Clear Fault”

A055 [Relay Out Sel] 0/9 0 = “Ready”(Not Faulted)

1 = “At Frequency”

2 = “Motor Running”

3 = “Reverse”

4 = “Motor Overload”

5 = “Ramp Regulated”

6 = “Above Frequency”

7 = “Above Current”

8 = “Above DC Bus Volts”

9 = “Retries Exhausted”

A056 [Relay Out Level] 0.0/9999 0.1 –1 0.0

A067 [Accel Time 2] 0.0/600.0 Secs 0.1 Secs 20.0 Secs

A068 [Decel Time 2] 0.1/600.0 Secs 0.1 Secs 20.0 Secs

A069 [Internal Freq] 0.0/240.0 Hz 0.1 Hz 60.0 Hz

See the PowerFlex 4 User Manual on CD for more information on parameters.

Allen-Bradley Drives

English-10

A070

A071

A072

A073

[Preset Freq 0](1)

[Preset Freq 1]

[Preset Freq 2]

[Preset Freq 3]

0.0/240.0 Hz 0.1 Hz 0.0 Hz

5.0 Hz

10.0 Hz

20.0 Hz

(1) To activate [Preset Freq 0] set P038 [Speed Reference] to option 4.

A078 [Jog Frequency] 0.0/[Maximum Freq] 0.1 Hz 10.0 Hz

A079 [Jog Accel/Decel] 0.1/600.0 Secs 0.1 Secs 10.0 Secs

A080 [DC Brake Time] 0.0/90.0 Secs 0.1 Secs 0.0 Secs

A081 [DC Brake Level] 0.0/(Drive Amps ×1.8) 0.1 Amps Amps ×0.05

A082 [DB Resistor Sel] 0/99 0 = Disabled

1 = 5% Duty Cycle

2 = 100% Duty Cycle

3-99 = % of Duty Cycle

A083 [S Curve %] 0/100% 1% 0% (Disabled)

A084 [Start Boost] 1/14 Settings in % of base voltage. 8

7 (5 HP Drives)

Variable Torque Constant Torque

1 = “30.0”5 = “0.0 no IR Comp”10 = “10.0”

2 = “35.0”6 = “0.0”11 = “12.5”

3 = “40.0”7 = “2.5”12 = “15.0”

4 = “45.0”8 = “5.0”13 = “17.5”

9 = “7.5”14 = “20.0”

A088 [Maximum Voltage] 20/Rated Volts 1 VAC Rated Volts

A089 [Current Limit] 0.1/(Drive Amps ×1.8) 0.1 Amps Amps ×1.5

A090 [Motor OL Select] 0/2 0 = “No Derate”1 = “Minimum Derate”

2 = “Maximum Derate”

A091 [PWM Frequency] 2.0/16.0 kHz 0.1 kHz 4.0 kHz

A092 [Auto Rstrt Tries] 0/9 1 0

A093 [Auto Rstrt Delay] 0.0/120.0 Secs 0.1 Secs 1.0 Secs

A094 [Start At PowerUp] 0/1 0 = “Disabled”1 = “Enabled”0

A095 [Reverse Disable] 0/1 0 = “Reverse Enabled”1 = “Reverse Disabled”0

A096 [Flying Start En] 0/1 0 = “Disabled”1 = “Enabled”0

A097 [Compensation] 0/3 0 = “Disabled”

1 = “Electrical”

2 = “Mechanical”

3 = “Both”

A098 [SW Current Trip] 0.0/(Drive Amps × 2) 0.1 Amps 0.0 (Disabled)

A099 [Process Factor] 0.1/999.9 0.1 30.0

A100 [Fault Clear] 0/2 0 = “Ready”1 = “Reset Active Fault”

2 = “Clear Fault Queue”

A101 [Program Lock] 0/1 0 = “Unlocked”1 = “Locked”0

A102 [Testpoint Sel] 0/FFFF 1 Hex 400

A103 [Comm Data Rate](3) 0/5 0 = “1200”

1 = “2400”

2 = “4800”

3 = “9600”

4 = “19.2K”

5 = “38.4K”

A104 [Comm Node Addr](3) 1/247 1 100

A105 [Comm Loss Action] 0/3 0 = “Fault”

1 = “Coast to Stop”

2 = “Stop”

3 = “Continue Last Speed”

A106 [Comm Loss Time] 0.1/60.0 0.1 5.0

A107 [Comm Format](3) 0/2 0 = “RTU 8-N-1”1 = “RTU 8-E-1”

2 = “RTU 8-O-1”

A110 [0-10V Analog Input

Low]

0.0/100.0% 0.1% 0.0

A111 [0-10V Analog Input

High]

0.0/100.0% 0.1% 100.0

A112 [4-20mA Analog Input

Low]

0.0/100.0% 0.1% 0.0

A113 [4-20mA Analog Input

High]

0.0/100.0% 0.1% 100.0

A114 [Slip Compensation] 0.0/10.0 Hz 0.1 Hz 2.0 Hz

(3) Power to drive must be cycled before any changes will affect drive operation.

No. Parameter Min/Max Display/Options Default

Input State of Digital In 1

(I/O Terminal 05)

Input State of Digital In 2

(I/O Terminal 06) Frequency Source Accel / Decel Parameter Used (2)

0 0 [Preset Freq 0] [Accel Time 1] / [Decel Time 1]

1 0 [Preset Freq 1] [Accel Time 1] / [Decel Time 1]

0 1 [Preset Freq 2] [Accel Time 2] / [Decel Time 2]

1 1 [Preset Freq 3] [Accel Time 2] / [Decel Time 2]

(2) When a Digital Input is set to “Accel 2 & Decel 2”, and the input is active, that input overrides the settings in this table.

See the PowerFlex 4 User Manual on CD for more information on parameters.

Andere Handbücher für PowerFlex 4

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Allen-Bradley Controller Handbücher

Allen-Bradley

Allen-Bradley ArmorStart 290E Bedienungsanleitung

Allen-Bradley

Allen-Bradley Series B Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 525 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 70 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Micro800 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Studio 5000 Logix Emulate Betriebsanleitung

Allen-Bradley

Allen-Bradley 1769-L32E CompactLogix 5332E Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 527 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1336 PLUS II Bedienungsanleitung

Allen-Bradley

Allen-Bradley Micro830 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Studio 5000 Logix Emulate Betriebsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 525 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 7760 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 198E-C2S4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 750 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 755 IP00 Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1200 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SoftLogix 5800 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 7000 Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1100 Bedienungsanleitung

Allen-Bradley

Allen-Bradley GuardLogix 5570 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Micro800 Gebrauchsanweisung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch