Allen-Bradley PowerFlex 700S Bedienungsanleitung

Publication 20D-IN027A-EN-P

PowerFlex 700S Power Jumpers

Frames 1…6

Installation Instructions

The PowerFlex 700S drive contains protective MOVs and Common Mode

Capacitors referenced to ground (see below). To guard against unstable

operation and/or damage, the drive must be properly configured as shown in

Table A on page 2.

Important: All PowerFlex 700S drives, frames 1…6, are shipped with the DC

bus common mode capacitors referenced to ground.

For additional general information, refer to:

Title Publication Available Online at …

PowerFlex 700S Phase II Drives, Frames 1…6

Installation Instructions

20D-IN024 www.rockwellautomation.com/

literature

Wiring and Grounding Guidelines for PWM AC Drives DRIVES-IN001

Guarding Against Electrostatic Damage 8000-4.5.2

DC+

DC–

R/L1

S/L2

T/L3

MOV and AC EMI Capacitor Phase to Ground

Common Mode Capacitor to Ground

Jumper-Wire

Publication 20D-IN027A-EN-P

Before proceeding, ensure that all power to the drive has been removed.

Table A Recommended Power Jumper Configurations

To connect or disconnect these devices, refer to pages 4through 7.

!ATTENTION: This drive contains ESD (Electrostatic Discharge)

sensitive parts and assemblies. Static control precautions are required

when installing, testing, servicing or repairing this assembly.

Component damage may result if ESD control procedures are not

followed. If you are not familiar with static control procedures,

reference A-B publication 8000-4.5.2, Guarding Against

Electrostatic Damage or any other applicable ESD protection guide.

!ATTENTION: Only qualified personnel familiar with adjustable

frequency AC drives and associated machinery should perform

maintenance/repair of the system. Failure to comply may result in

personal injury and/or equipment damage.

!ATTENTION: To avoid an electric shock hazard, verify that the

voltage on the bus capacitors has discharged before performing any

work on the drive. Measure the DC bus voltage at the +DC & –DC

terminals of the Power Terminal Block (refer to the User Manual for

location). The voltage must be zero.

!ATTENTION: The following information is merely a guide for

proper installation. Rockwell Automation cannot assume

responsibility for the compliance or the noncompliance to any code,

national, local or otherwise for the proper installation of this drive or

associated equipment. A hazard of personal injury and/or equipment

damage exists if codes are ignored during installation.

Power Source Type (1)

(1) It is highly recommended to accurately determine the power source type and then configure appropriately.

MOV/Input

Filter Caps (2)

(2) When MOVs are disconnected, the power system must have its own transient protection to ensure known and

controlled voltages.

DC Bus

Common Mode

Caps

Benefits Of Correct

Configuration on Power Source

Type

Solid Ground

•AC fed, solidly grounded

•DC fed from passive rectifier

which has an AC source and

solid ground

Connected Connected •UL compliance,

•Reduced electrical noise,

•Most stable operation,

•EMC compliance,

•Reduced voltage stress on

components and motor

bearings

Non-Solid Ground

•AC fed ungrounded

•Impedance grounded

•High resistive ground

•B phase ground

•Regenerative unit such as

common DC bus supply & brake

•DC fed from an active converter

Disconnected Disconnected •Helps avoid severe equipment

damage when ground fault

occurs

Publication 20D-IN027A-EN-P

Important: Common mode capacitors are required to conform with the EMC

directive. Removing these devices will withdraw the associated

directive.

In addition, on an ungrounded distribution system where the line-to-ground

voltages on any phase could exceed 125% of the nominal line-to-line voltage, an

isolation transformer should be installed. See Wiring and Grounding Guidelines

for PWM AC Drives, publication DRIVES-IN001 for more information on

impedance grounded and ungrounded systems.

Jumper Installation, Removal and Storage

PowerFlex 700S drives utilize plug-in style jumpers and jumper wires. Most

drives will have a jumper storage area inside the front cover. Extra jumpers or

jumpers that have been removed should be stored in this location for use at a

later time.

Insulating Jumper Wires

Some drives utilize nylon screws and spacers to insulate jumper

wires from ground and secure them to the chassis. The

components must be installed as shown.

Drive Identification

Refer to the drive nameplate and locate the “Voltage Code,” “Current Rating,”

“Frame,” and “Series”. Use this information to locate the proper procedure in

the following tables.

Cat No. 20D D xxx x x xxxxxxx

Made in the USA (TAC 1J)

Rockwell Automation, Mequon WI 53092-4400

UL TYPE 1/IP20

Mfd. in 2007 on Aug 1 Frame: 3

Serial Number: xxxxxxx

Series: B

Original Firmware V. x.xxx

Listed

Ind. Cont

Eq. 966X

Normal Duty Power

Heavy Duty Power

AC Voltage Range

Amps

Input: 3 Phase, 47-63Hz

Output: 3 Phase, 0-400 Hz

AC Voltage Range

Base Hz (default)

Continuous Amps

1 Min Overload Amps

3 Sec Overload Amps

xxx kW

342-440

xxx

0-400

50 Hz

xxx

xxx kW

432-528

xxx

400V 480V

0-460

60 Hz

xxx

N223

Voltage Code

Frame

Current Rating Series

Publication 20D-IN027A-EN-P

Jumper Settings and Locations

Frame

Voltage

Code

Current

Rating

Factory Default Jumper Settings

Power Source Type

MOV/Input Filter

Caps

DC Bus Common

Mode Caps

All PE_B

Installed

PE_A

Installed

Solid Ground

•Remove the I/O Cassette (refer to the

Installation Instructions for details).

Verify that jumpers are installed at the

“PE_A” and “PE_B” locations on the

Power Board.

Non-Solid Ground

•Remove the I/O Cassette (refer to the

Installation Instructions for details).

Remove jumpers at the “PE_A” and

“PE_B” locations on the Power Board.

All PE_MOV

Installed

PE_CAP

Installed

Solid Ground

•Verify that jumpers are installed at the

“PE_CAP” and “PE_MOV” locations.

Non-Solid Ground

•Remove jumpers at the “PE_CAP” and

“PE_MOV” locations.

3…4 B

All PE_MOV

Installed

PE-CAP

Installed

Solid Ground

•Verify that jumpers are installed at the

“PE_CAP” and “PE_MOV” locations.

Non-Solid Ground

•Remove jumpers at the “PE_CAP” and

“PE_MOV” locations.

BR1

BR2

DC+

DC–

U/T1

V/T2

W/T3

R/L1

S/L2

T/L3

Use 75C Wire Only

#10-#14 AWG

Torqueto 7 in-lbs

DANGER

PE A

PE B

CM Cap

MOV

BR1 BR2 DC+ DC- U/T1 V/T2 W/T3

SHLD SHLD

PE R/L1 S/L2 T/L3

PE 2

MOV-PEJMPR

PE 1

AUX IN+ AUXOUT–

75C Cu Wire

6 AWG [10MM2] Max.

12 IN. LBS.

1.4 N-M } TORQUE

WIRE

STRIP

CONTROL

POWER

PE 4 PE 3

MOV

PE_MOV

CM Cap

PE_CAP

BR1 BR2 DC+ DC- U/T1 V/T2 W/T3 R/L1 S/L2 T/L3

PE MOV

PE CAP

75C Cu Wire

3 AWG [25MM2] Max.

16 IN. LBS.

1.8 N-M } TORQUE

WIRE

STRIP

CONTROL

POWER

AUX IN

+ –

SHLD

75C Cu Wire

6 AWG [10MM2] Max.

BR1 BR2

12 IN. LBS.

1.4 N-M } TORQUE

PE_CAP

PE_MOV

CM Cap

MOV

Publication 20D-IN027A-EN-P

Frame 5 continued on next page

Frame

Voltage

Code

Current

Rating

Factory Default Jumper Settings

Power Source Type

MOV/Input Filter

Caps(1)(2) DC Bus Common

Mode Caps

All,

except

C140

(see

page)

Two green/yellow

wires connected

to the Power

Terminal Block rail

Green/yellow wire

is connected to

ground

Solid Ground

1. CM Cap jumper wire should be

connected to ground with a metal screw.

Verify.

•Newer Drives - If necessary, remove

the nylon screw/spacer and insert a

metal M5 x 8 screw. Torque to 3.2

N•m (28 lb•in).

•Older Drives - Remove the I/O

Cassette (see Installation Instructions

for details). The green/yellow CM Cap

jumper wire is located on the back of

chassis and should be connected to

ground with a metal screw. If

necessary, remove the insulation

from the wire terminal and connect to

chassis with a metal M5 x 12 screw.

Torque screw to 3.2 N•m (28 lb•in).

2. MOV/Input Filter Cap jumper wires

should be connected to ground with a

metal screw. Verify. If necessary, remove

the nylon screw/spacer and insert a

metal M5 x 12 screw.

Non-Solid Ground

1. CM Cap jumper wire should be insulated

from ground. Verify.

•Newer Drives - If necessary, remove

the metal screw and insert a M5 x 15

nylon screw/spacer.

•Older Drives - Remove the I/O

Cassette (see Installation Instructions

for details). If necessary, insulate/

secure jumper wire to guard against

unintentional contact with chassis or

components.

2. MOV/Input Filter Cap jumper wires

should be insulated from ground with a

nylon screw/spacer. Verify. If necessary,

remove the metal screw and insert a M5

x 20 nylon screw/spacer.

(1) AC input drives only. MOV’s and input filter caps do not exist on DC input drives.

(2) When removing MOV’s, the input filter capacitor must also be removed.

WIRE RANGE: 14-1/0 AWG(2.5-35 MM

)

TORQUE:32 IN-LB (3.6 N-M)

STRIP LENGTH: 0.67 IN (17 MM)

USE 75 C CU WIRE ONLY

POWER TERMINAL RATINGS

WIRE RANGE: 6-1/0 AWG(16-35 MM

)

TORQUE:44 IN-LB (5 N-M)

STRIP LENGTH: 0.83 IN (21 MM)

GROUND TERMINAL RATINGS(PE)

300 VDC EXT PWR SPLYTERM (PS+, PS-)

WIRE RANGE: 22-10 AWG(0.5-4 MM

)

TORQUE:5.3 IN-LB (0.6 N-M)

STRIP LENGTH: 0.35 IN (9 MM)

INPUT ACOUTPUT

Optional

Communications

Module

CM Cap -

Older Drives

MOV / Input Filter Cap

MOV

CM Cap - Newer Drives

Publication 20D-IN027A-EN-P

Frame

Voltage

Code

Current

Rating

Factory Default Jumper Settings

Power Source Type

MOV/Input Filter

Caps(1) (2) DC Bus Common

Mode Caps

140

052

060

Two green/yellow

wires connected

to the Power

Terminal Block rail

Green/yellow wire

to CM Cap Board

is connected to

ground

Solid Ground

1. CM Cap jumper wire should be connected

to ground with a metal screw. Verify. If

necessary, remove the nylon screw/spacer

and insert a metal M5 x 8 screw. Torque to

3.2 N•m (28 lb•in).

2. MOV/Input Filter Cap jumper wires should

be connected to ground with a metal screw.

Verify. If necessary, remove the nylon

screw/spacer and insert a metal M5 x 12

screw.

Non-Solid Ground

1. CM Cap jumper wire should be insulated

from ground with a nylon screw/spacer.

Verify. If necessary, remove the metal screw

and insert a M5 x 15 nylon screw/spacer.

2. MOV/Input Filter Cap jumper wires should

be insulated from ground with a nylon

screw/spacer. Verify. If necessary, remove

the metal screw and insert a

M5 x 20 nylon screw/spacer.

077

082

099

098

Two green/yellow

wires connected

to chassis ground

Green/yellow wire

to CM Cap Board

is connected to

ground

Solid Ground

1. CM Cap jumper wire should be connected

to ground with a metal screw. Verify. If

necessary, remove the nylon screw/spacer

and insert a metal M5 x 8 screw. Torque to

3.2 N•m (28 lb•in).

2. MOV jumper wire should be connected to

ground with metal screws. Verify. If

necessary, remove the nylon screw/spacers

and insert metal M5 x 12 screws.

3. Input Filter Cap jumper wire should be

connected to ground with a metal screw.

Verify. If necessary, remove the nylon

screw/spacer and insert metal M5 x 8

screw.

Non-Solid Ground

1. CM Cap jumper wire should be insulated

from ground with a nylon screw/spacer.

Verify. If necessary, remove the metal screw

and insert a M5 x 15 nylon screw/spacer.

2. MOV jumper wire should be insulated from

ground with a nylon screw/spacer. Verify. If

necessary, remove the metal screws and

insert a M5 x 20 nylon screw/spacer.

3. Input Filter Cap jumper wire should be

insulated from ground with a nylon screw/

spacer. Verify. If necessary, remove the

metal screws and insert a M5 x 15 nylon

screw/spacer.

(1) AC input drives only. MOV’s and input filter caps do not exist on DC input drives.

(2) When removing MOV’s, the input filter capacitor must also be removed.

WIRE RANGE: 14-1/0 AWG(2.5-35 MM2)

TORQUE:32 IN-LB (3.6 N-M)

STRIP LENGTH: 0.67 IN (17 MM)

USE 75 C CU WIRE ONLY

POWER TERMINAL RATINGS

WIRE RANGE: 6-1/0 AWG(16-35 MM2)

TORQUE:44 IN-LB (5 N-M)

STRIP LENGTH: 0.83 IN (21 MM)

GROUND TERMINAL RATINGS(PE)

300 VDC EXT PWR SPLYTERM (PS+, PS-)

WIRE RANGE: 22-10 AWG(0.5-4 MM2)

TORQUE:5.3 IN-LB (0.6 N-M)

STRIP LENGTH: 0.35 IN (9 MM)

INPUT ACOUTPUT

Optional

Communications

Module

CM Cap MOV

MOV / Input Filter Cap

WIRE RANGE: 14-1/0 AWG(2.5-35 MM2)

TORQUE:32 IN-LB (3.6 N-M)

STRIP LENGTH: 0.67 IN (17 MM)

USE 75 C CU WIRE ONLY

POWER TERMINAL RATINGS

WIRE RANGE: 6-1/0 AWG(16-35 MM2)

TORQUE:44 IN-LB (5 N-M)

STRIP LENGTH: 0.83 IN (21 MM)

GROUND TERMINAL RATINGS(PE)

300 VDC EXT PWR SPLYTERM (PS+, PS-)

WIRE RANGE: 22-10 AWG(0.5-4 MM2)

TORQUE:5.3 IN-LB (0.6 N-M)

STRIP LENGTH: 0.35 IN (9 MM)

INPUT ACOUTPUT

Optional

Communications

Module

CM Cap

MOV

Input Filter

Cap

Publication 20D-IN027A-EN-P

Frame

Voltage

Code

Current

Rating

Factory Default Jumper Settings

Power Source Type

MOV/Input Filter

Caps(1) (2) DC Bus Common

Mode Caps

All Two green/yellow

wires connected

to Power Terminal

Block “PE”

Green/yellow wire

to CM Cap Board

is connected to

Power Terminal

Block “PE”

Solid Ground

1. The green/yellow CM Cap jumper wire

should be connected to “PE.”

2. The MOV/Input Filter Cap jumper wires

should be connected to “PE.”

Non-Solid Ground

1. The green/yellow CM Cap jumper wire

should be insulated from ground. If

necessary, remove the jumper wire

from “PE” and insulate/secure it to

guard against unintentional contact

with chassis or components.

Important: Do Not Remove/

Disconnect the larger green/yellow

wire.

2. MOV/Input Filter Cap jumper wires

should be insulated from ground. If

necessary, remove the jumper wires

from “PE” and individually insulate/

secure each jumper wire to guard

against unintentional contact with

chassis or components.

All Two green/yellow

wires connected

to Power Terminal

Block “PE” and

chassis

Green/yellow wire

to CM Cap Board

is connected to

Power Terminal

Block “PE”

Solid Ground

1. The green/yellow CM Cap and MOV

jumper wires should be connected to

“PE.”

2. The Input Filter Cap jumper wire (top

right) should be connected to chassis

ground with a metal screw. Verify. If

necessary, remove the nylon screw/

spacer and insert a metal M5 x 10

screw. Torque to 3.2 N•m (28 lb•in).

Non-Solid Ground

1. The green/yellow CM Cap and MOV

jumper wires should be insulated from

ground. If necessary, remove them

from “PE” and individually insulate/

secure each jumper wire to guard

against unintentional contact with

chassis or components. Important: Do

Not Remove/Disconnect the larger

green/yellow wire.

2. The Input Filter Cap jumper wire (top

right) should be insulated from ground

with a nylon screw/spacer. Verify. If

necessary, remove the metal screw

and insert a M5 x 15 nylon screw/

spacer.

(1) AC input drives only. MOV’s and input filter caps do not exist on DC input drives.

(2) When removing MOV’s, the input filter capacitor must also be removed.

DC–DC+BR1BR2

USE 75 C COPPER WIRE ONLY, TORQUE52 IN-LB (6 N-M)

22-10

AWG

5.3IN-LB

(0.6N-M)

WIRESTRIP

PS+

PS–

USE 75 C

COPPER WIRE

ONLY

TORQUE

52 IN-LB

(6 N-M)

T1 V

T2 W

T3 R

L1 S

INPUTOUTPUT

PE PE

Optional

Communications

Module

PE PE

MOV

Input Filter Cap

CM Cap

DO NOT

REMOVE

MOV

DC–DC+BR1BR2

USE 75 C COPPER WIRE ONLY, TORQUE52 IN-LB (6 N-M)

22-10

AWG

5.3IN-LB

(0.6N-M)

WIRESTRIP

PS+

PS–

USE 75 C

COPPER WIRE

ONLY

TORQUE

52 IN-LB

(6 N-M)

T1 V

T2 W

T3 R

L1 S

INPUTOUTPUT

PE PE

Optional

Communications

Module

Input Filter Cap

PE PE

MOV

CM Cap

DO NOT

REMOVE

MOV

www.rockwellautomation.com

Americas: Rockwell Automation, 1201 South Second Street, Milwaukee,WI 53204 USA,Tel: (1) 414.382.2000, Fax: (1) 414.382.4444

Europe/Middle East/Africa: Rockwell Automation,Vorstlaan/Boulevard du Souverain 36, 1170 Brussels, Belgium,Tel: (32) 2 663 0600, Fax: (32) 2 663 0640

Asia Pacific:Rockwell Automation, Level 14, Core F, Cyberport 3, 100 Cyberport Road, Hong Kong,Tel: (852) 2887 4788, Fax: (852) 2508 1846

Power, Control and Information Solutions Headquarters

Publication 20D-IN027A-EN-P – August, 2010 PN-48718

U.S. Allen-Bradley Drives Technical Support - Tel: (1) 262.512.8176, Fax: (1) 262.512.2222, Email: suppor[email protected]kwell.com, Online: www.ab.com/support/abdrives

PN-48718*

PN-48718

Andere Handbücher für PowerFlex 700S

Inhaltsverzeichnis

Andere Allen-Bradley Controller Handbücher

Allen-Bradley

Allen-Bradley Studio 5000 Logix Emulate Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1769 CompactLogix Bedienungsanleitung

Allen-Bradley

Allen-Bradley PLC-5 series Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 7000 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 70 Bedienungsanleitung

Allen-Bradley

Allen-Bradley CompactLogix 1769-L20 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 527 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 161S-AA04NPU Bedienungsanleitung

Allen-Bradley

Allen-Bradley 198E-C2S4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 700S Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 700L Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix System 1756-L1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley GuardLogix 5570 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 755 IP00 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 40P Bedienungsanleitung

Allen-Bradley

Allen-Bradley Micro800 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 70 Bedienungsanleitung

Allen-Bradley

Allen-Bradley GuardPLC 1754 Bedienungsanleitung

Allen-Bradley

Allen-Bradley powerflex 700 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Studio 5000 Logix Emulate Betriebsanleitung

Allen-Bradley

Allen-Bradley SMC-50 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 140G-M-F Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2080-LC20-20QWB Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch