Allen-Bradley PowerFlex 700H Bedienungsanleitung

Installation Instructions

PowerFlex®700S and 700H Frame 10

Replacement Power Structures

Introduction Use this document to install a replacement power structure on a PowerFlex

700S or 700H frame 10 drive. This document covers the following

replacement power structures:

Spare Module Catalog

String

PowerFlex 700H

AC Input

PowerFlex 700H

DC Input

PowerFlex 700S

AC Input

PowerFlex 700S

DC Input

SK-H1-PWRMOD-D385 20CC385 20CH385 20DC385 20DH385

20CD385 20CJ385 20DD385 20DJ385

SK-H1-PWRMOD-D460 20CC460 20CH460 20DC460 20DH460

20CD460 20CJ460 20DD460 20DJ460

SK-H1-PWRMOD-D500 20CC500 20CH500 20DC500 20DH500

20CD500 20CJ500 20DD500 20DJ500

SK-H1-PWRMOD-E261 20CE261 20CK261 20DE261 20DK261

20CF261 20CM261 20DF261 20DM261

SK-H1-PWRMOD-E325 20CE325 20CK325 20DE325 20DK325

20CF325 20CM325 20DF325 20DM325

SK-H1-PWRMOD-E385 20CE385 20CK385 20CF385 20DK385

20CF385 20CM385 20DF385 20DM385

SK-H1-PWRMOD-E416 20CE416 20CK416 20DE416 20DK416

20CF416 20CM416 20DF416 20DM416

2PowerFlex® 700S and 700H Frame 10 Replacement Power Structures

What You Need to Do ❐ Step 1: Configure new power structure

❐ Step 2: Remove power from existing drive

❐ Step 3: Remove old power structure

❐ Step 4: Install new power structure

❐ Step 5: Connect power structure to components in drive

❐ Step 6: Install product identification label on new power structure

❐ Step 7: Start drive

!ATTENTION: To avoid an electric shock hazard, ensure that all

power to the drive has been removed before performing the

following.

!ATTENTION: To avoid an electric shock hazard, verify that the

voltage on the bus capacitors has discharged before servicing the

drive. Check the DC bus voltage at the Power Terminal Block by

measuring between the +DC & -DC terminals, between the +DC

terminal and the chassis, and between the -DC terminal and the

chassis. The voltage must be zero for all three measurements.

!ATTENTION: HOT surfaces can cause severe burns. Do not

touch the heatsink surface during operation of the drive. After

disconnecting power allow time for cooling.

!ATTENTION: Hazard of permanent eye damage exists when

using optical transmission equipment. This product emits intense

light and invisible radiation. Do not look into SynchLink

fiber-optic ports or SynchLink fiber-optic cable connectors.

!ATTENTION: This drive contains ESD (Electrostatic

Discharge) sensitive parts and assemblies. Static control

precautions are required when installing, testing, servicing or

repairing this assembly. Component damage may result if ESD

control procedures are not followed. If you are not familiar with

static control procedures, reference A-B publication 8000-4.5.2,

“Guarding Against Electrostatic Damage” or any other

applicable ESD protection handbook.

!ATTENTION: The sheet metal cover and mounting screws on

the ASIC Board located on the power structure are energized at

(-) DC bus potential high voltage. Risk of electrical shock, injury,

or death exists if someone comes in contact with the assembly.

PowerFlex® 700S and 700H Frame 10 Replacement Power Structures 3

Step 1: Configuring the

New Power Structure

Before configuring the new power structure you must remove the protective

covers. Refer to the Installation Instructions - PowerFlex 700S and 700H

High Power Drives, publication PFLEX-IN006…for instructions on

removing these covers.

Configuring a DC Input Drive

Power structures are shipped from the factory pre-configured for DC input

operation.

Connecting an AC Input Drive

Power structures are shipped from the factory pre-configured for DC input

operation. When installing a replacement power structure on a drive with

AC input, you must remove the X2 plug from it’s protective sleeve and plug

the cable into the ASIC and Rectifier board.

Figure 1 ASIC Board Connections

Task Description

Remove the screw that secures the X6 connector wire to the ASIC cover and remove the

wire.

Remove the remaining screws that secure the cover to the ASIC assembly and remove the

cover.

Disconnect the ASIC fan from the assembly by unplugging the cable from X1 on the ASIC

board (see Figure 1 below for location).

Remove the cover from the connector on the loose cable (bundled with the flat gate driver

board cables) and connect the cable to the X2 connector on the ASIC board (see Figure 1

below for location).

Connect the other end of the cable connected to X2 on the ASIC board to the X13

connector for the Rectifier board on the upper right side of the power structure.

Connect the fan cable to the X1 connector on the ASIC board.

Install the cover on the ASIC board assembly.

H11

H12

H13

H10

X15

X1 H4

Connect cable to

X2 connector X1 connector

4PowerFlex® 700S and 700H Frame 10 Replacement Power Structures

Configuring the EMC Filter

Frame 10 size drives are equipped with common mode capacitors and

capacitors that are connected to the input terminals. To guard against drive

damage, these capacitors should be disconnected depending upon the type

of ground system on which the drive is installed.

Installation on an Ungrounded Distribution System or High Resistive Ground

If you are installing a 400/480V AC input drive on an ungrounded

distribution system or high resistive ground, you:

•Must move the common mode jumper to the disconnected position -

refer to Move the Common Mode Jumper to the Disconnected

Position on page 6.

•Should insulate terminal X4 on the Rectifier circuit board- refer to

Insulate Terminal X4 on the Rectifier Circuit Board on page 7.

•Must disconnect the small capacitors from the input terminals - refer to

Disconnect the Small Capacitors from the Input Terminals on page 8.

If you are installing a 600/690V AC input drive on an ungrounded

distribution system or high resistive ground you:

•Must move the common mode jumper to the disconnected position -

refer to Move the Common Mode Jumper to the Disconnected

Position on page 6.

•Must insulate terminal X4 on the Rectifier circuit board- refer to Insulate

Terminal X4 on the Rectifier Circuit Board on page 7.

•Must disconnect the small capacitors from the input terminals - refer to

Disconnect the Small Capacitors from the Input Terminals on page 8.

Installation on a Grounded B Phase Delta System

If you are installing a drive on a grounded B phase Delta system you:

•Must move the common mode jumper to the disconnected position -

refer to Move the Common Mode Jumper to the Disconnected

Position on page 6.

•Must insulate terminal X4 on the Rectifier circuit board- refer to Insulate

Terminal X4 on the Rectifier Circuit Board on page 7.

•Must disconnect the small capacitors from the input terminals - refer to

Disconnect the Small Capacitors from the Input Terminals on page 8.

Note: Refer to the Wiring and Grounding Guidelines for Pulse Width

Modulated (PWM) AC Drives - Installation Instructions,

publication DRIVES-IN001…, for additional information on an

ungrounded distribution system or high resistive ground

installation.

PowerFlex® 700S and 700H Frame 10 Replacement Power Structures 5

Figure 2 Common Mode Jumper and Rectifier Circuit Board Location

Common

Mode jumper

Rectifier Circuit Board

Front View

of Assembly

There is one common

mode jumper located on

the upper-right side of the

power structure.

6PowerFlex® 700S and 700H Frame 10 Replacement Power Structures

Move the Common Mode Jumper to the Disconnected Position

Follow the lettered steps below to move the common mode jumper to the

disconnected position (refer to Figure 2 on page 5 for jumper location):

Task Description

Loosen the upper screw.

Remove the lower screw.

Move the jumper to the horizontal position.

Install and tighten the screws.

Rectifier Circuit Board

Front View of

Power Structure

PowerFlex® 700S and 700H Frame 10 Replacement Power Structures 7

Insulate Terminal X4 on the Rectifier Circuit Board

Follow the lettered steps below to insulate terminal X4 on the Rectifier

circuit board (refer to Figure 2 on page 5 for Rectifier board location):

Important:Do not install the screw and washer that was removed from this

connection.

Task Description

Remove the screw from the X4 connection on the Rectifier circuit board.

Insulate the top and bottom of the X4 connection on the Rectifier circuit board.

X41

Rectifier Circuit Board

Side View of Power Structure

8PowerFlex® 700S and 700H Frame 10 Replacement Power Structures

Disconnect the Small Capacitors from the Input Terminals

Follow the lettered steps below to disconnect the small capacitors from the

input terminals:

Important:Do not re-install the capacitor leads.

Task Description

Remove the screws and lock washers that secure each of the three capacitor supply wires

to the input power terminals.

Insulate the capacitor leads and leave disconnected.

Install and tighten the screws and lock washers only.

L1 L2 L3

Capacitor

Insulator

Capacitor lead -

leave disconnected

Input power terminal

Front View of Input

Power Terminals

Side View of Input

Power Terminals

PowerFlex® 700S and 700H Frame 10 Replacement Power Structures 9

Step 2: Removing Power

From the Existing Drive

1. Turn off and lock out input power. Wait five minutes.

2. Verify that there is no voltage at the drive’s input power terminals.

3. Check the DC bus voltage at the Power Terminal Block by measuring

between the +DC & -DC terminals, between the +DC terminal and the

chassis, and between the -DC terminal and the chassis. The voltage

must be zero for all three measurements.

Step 3: Removing the Old

Power Structure

Refer to the PowerFlex 700H/S Frame 10 Hardware Service Manual,

publication PFLEX-TG002…, for information about removing the old

power structure.

Step 4: Installing the New

Power Structure

Refer to the PowerFlex 700H/S Frame 10 Hardware Service Manual,

publication PFLEX-TG002…, for information about installing the new

power structure.

!ATTENTION: To avoid an electric shock hazard, verify that the

voltage on the bus capacitors has discharged before servicing the

drive. Check the DC bus voltage at the Power Terminal Block by

measuring between the +DC & -DC terminals, between the +DC

terminal and the chassis, and between the -DC terminal and the

chassis. The voltage must be zero for all three measurements.

Remove power before making or breaking cable connections.

When you remove or insert a cable connector with power

applied, an electrical arc may occur. An electrical arc can cause

personal injury or property damage by:

•sending an erroneous signal to your system’s field devices,

causing unintended machine motion

•causing an explosion in a hazardous environment

Electrical arcing causes excessive wear to contacts on both the

module and its mating connector. Worn contacts may create

electrical resistance.

L1 L2 L3

10 PowerFlex® 700S and 700H Frame 10 Replacement Power Structures

Step 5: Connecting the

Power Structure to

Components in the Drive

You must connect the new power structure to the components in the drive. If

the drive has DC input, you must also connect the pre-charge circuit.

Connections to the 700S Control

When installing a power structure in a PowerFlex 700S drive, you must

make the following connections between the ASIC board and the Fiber

Optic Interface, Power Supply Voltage Feedback, Common Mode Filter and

Rectifier boards.

Connect this component: termination point in

the Power Structure to …

…this component : termination point on the

Control Frame

ASIC Board: H1 (fiber optic connector) Fiber Optic Interface Board: J8 (fiber optic

connector)

ASIC Board: H2 (fiber optic connector) Fiber Optic Interface Board: J9 (fiber optic

connector)

ASIC Board: H3 (fiber optic connector) Fiber Optic Interface Board: J10 (fiber optic

connector)

ASIC Board: H4 (fiber optic connector) Fiber Optic Interface Board: J11 (fiber optic

connector)

ASIC Board: H5 (fiber optic connector) Fiber Optic Interface Board: J12 (fiber optic

connector)

ASIC Board: H6 (fiber optic connector) Fiber Optic Interface Board: J14 (fiber optic

connector)

ASIC Board: H7 (fiber optic connector) Fiber Optic Interface Board: J13 (fiber optic

connector)

ASIC Board: X10 Insulate and do not connect

ASIC Board: X2 Rectifier Board: X13

Power Supply Voltage Feedback Board: J8 Common Mode Filter Board: J5

Power Supply Voltage Feedback Board: J4

(fiber optic connector)

Fiber Optic Interface Board: J6

Power Supply Voltage Feedback Board: J6

(fiber optic connector)

Fiber Optic Interface Board: J7

Andere Handbücher für PowerFlex 700H

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Allen-Bradley Gleichstromantrieb Handbücher

Allen-Bradley

Allen-Bradley PowerFlex 70 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 4M Bedienungsanleitung

Allen-Bradley

Allen-Bradley 25-JBAA Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 6000 Programmierhandbuch

Allen-Bradley

Allen-Bradley PowerFlex 23P Bedienungsanleitung

Allen-Bradley

Allen-Bradley Ultra1500 2092-DA1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 4M Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 700S Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1398 ULTRA Plus Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley powerflex 700 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 40 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 70 Enhanced Control Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 755T Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 700S Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 40P Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 755 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 70 Bedienungsanleitung

Allen-Bradley

Allen-Bradley The PowerFlex 755 On-Machine Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 520 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 6000T Bedienungsanleitung

Allen-Bradley

Allen-Bradley Rockwell Automation PowerFlex 700 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex SK-20P-S725804 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 6000 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1395 Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung

Beckhoff

Beckhoff AX8911 Bedienerhandbuch

Lenze

Lenze 8200 vector Bedienungsanleitung