Allen-Bradley PowerFlex 700S Bedienungsanleitung

Release Notes

PowerFlex 700S Drives with Phase II Control (30.001)

Bulletin 20D

These release notes correspond to major revision 30, minor revision 1 of

firmware for PowerFlex® 700S drives with Phase II control.

IMPORTANT Firmware revision 30.001 is compatible with PowerFlex 700S drives with Phase II

control series A main control boards only. To determine your main control board

version, see Determine Your Main Control Board Version on page 5.

Topic Page

Determine the Firmware Revision 2

Determine Your Main Control Board Version 5

Firmware Upgrades 6

New Features and Enhancements 10

Corrected Anomalies 10

Known Anomalies 10

Restrictions 12

Rockwell Automation Publication 20D-RN047A-EN-P - October 2019

Determine the Firmware

Revision

This section describes procedures to determine the firmware revision of your

PowerFlex 700S Phase II drive. Use one of these methods to determine the

firmware revision.

Use the LCD Human Interface Module (HIM)

Step Key(s) Example Screens

1. In the main menu, press the Up Arrow or Down

Arrow to scroll to Device Select (as shown in the

example to the right).

2. Press Enter to enter your selection.

3. Press the Up Arrow or Down Arrow to scroll to the

PowerFlex 700S 2 drive.

4. Press Enter to select the drive. The main menu for

the drive displays.

5. Press the Up Arrow or Down Arrow to scroll to

Diagnostics (as shown in the example to the

right).

6. Press Enter to enter your selection.

7. Press the Up Arrow or Down Arrow to scroll to

Device Version.

8. Press Enter to display the Product Data screen.

9. Press Enter again to display the firmware version of

the drive (as shown in the example to the right).

F-> Stopped Auto

0.00 RPM

Main Menu:

Diagnostics

Parameter

Device Select

F-> Stopped Auto

Main Menu:

Diagnostics

Parameter

Device Select

F-> Stopped Auto

Diag. Product Ver

FW Ver: 6.003

Series: A

Date: 01/26/2016

Rockwell Automation Publication 20D-RN047A-EN-P - October 2019

Use DriveExplorer Lite/Full

1. Launch DriveExplorer™ and go online (via EtherNet/IP™ by using

DriveExplorer Full only, or a 1203-USB or 1203-SSS converter) with the

drive.

2. In the DriveExplorer treeview, click on the PowerFlex 700S 2 drive as

shown in Figure 1 - Example DriveExplorer Window.

3. Click the information icon to display the Properties screen of the drive.

4. The Revision: field shows the present revision (for example, 4.002) of the

drive firmware.

5. The Series: field shows the series (for example, A) of the control board of

the drive.

Figure 1 - Example DriveExplorer Window

TIP When clicking on the drive using version 5.01 or higher DriveExplorer Lite/Full, the

adapter firmware revision is also shown in the right pane of the DriveExplorer window.

Step 2

Step 3

Step 4

Step 5

Rockwell Automation Publication 20D-RN047A-EN-P - October 2019

Use DriveExecutive

1. Launch DriveExecutive™ and go online (via EtherNet/IP, or a 1203-USB

or 1203-SSS converter) with the drive.

2. In the DriveExecutive treeview, click on the PowerFlex 700S 2 drive as

shown in Figure 2 - Example DriveExecutive Window.

3. Click the information icon to display the Properties screen of the drive.

4. The Revision: field shows the present revision (for example, 4.002) of the

drive firmware.

5. The Series: field shows the series (for example, A) of the control board of

the drive.

Figure 2 - Example DriveExecutive Window

Step 3

Step 2

Step 4

Step 5

Rockwell Automation Publication 20D-RN047A-EN-P - October 2019

Determine Your Main Control

Board Version

Use one of these methods to determine the version of your PowerFlex 700S with

Phase II control main control board.

Use DriveExecutive Software

Follow these steps to use DriveExecutive software to view the main control board

version.

1. Connect to the drive.

2. Open the Properties window and select the Component Details tab.

3. View the Main Control Board Product Series.

Use Connected Component Workbench Software

Follow these steps to use Connected Component Workbench® software to view

the main control board version.

1. Connect to the drive.

2. In the Device Details window, select Device Info.

3. View the Main Control Board Product Series.

Use the HIM

Follow these steps to view the main control board version.

1. On the HIM, navigate to the Diagnostics menu.

2. Choose Device Version.

3. View the Main Control Board series.

Rockwell Automation Publication 20D-RN047A-EN-P - October 2019

Firmware Upgrades

This section describes procedures to flash upgrade your drive firmware. Flash kits

for drives and communications adapters are provided on the Product

Compatibility & Download Center (PCDC), located at

https://compatibility.rockwellautomation.com/Pages/home.aspx. Flashing can

be performed using a drive software tool over EtherNet/IP, or a 1203-USB or

1203-SSS converter. For information about how to connect to your drive, please

see the 1203-USB or 1203-SSS User Manual. They can be viewed/downloaded

on the Literature Library website located at

https://www.rockwellautomation.com/global/literature-library/overview.page.

Install the Flash Kit

Follow these steps to install the ControlFLASH™ kit.

1. Install the flash kit utility from the PCDC for the PowerFlex 700S Phase

II drive. (This installation also automatically installs the latest version of

the ControlFLASH software and deploys the firmware files on your

computer for flashing the drive using software tools, such as

DriveExplorer, DriveExecutive, or HyperTerminal™.)

2. You are now ready to use DriveExplorer, DriveExecutive, ControlFLASH

or HyperTerminal to update the drive. See the respective section below and

follow the instructions.

Use DriveExplorer Lite/Full

Follow these steps to used DriveExplorer Lite or Full to upgrade your firmware.

1. With the Flash Kit installed (see Install the Flash Kit above), launch

DriveExplorer and go online (via EtherNet/IP using DriveExplorer Full

only, or a 1203-USB or 1203-SSS converter) with the drive.

2. In the DriveExplorer treeview, click on the PowerFlex 700S Phase II drive.

Then click the information icon as shown in Figure 1 - on page 3 to display

the Properties screen of the drive.

ATTENTION: Risk of permanent equipment damage exists. Once a flash update has

been started, do not remove power from the drive (or the 20-XCOMM-DC-BASE External

Comms Kit, if used) until after the download has completed and the adapter MOD status

indicator starts flashing green. If power is removed before this occurs, the adapter may

be permanently damaged. An adapter that has been damaged in this way cannot be

repaired.

IMPORTANT Firmware revision 30.001 is compatible with PowerFlex 700S drives with Phase II

control series A main control boards only. To determine your main control board

version, see Determine Your Main Control Board Version on page 5.

Rockwell Automation Publication 20D-RN047A-EN-P - October 2019

3. On the PowerFlex 700S Phase II Properties screen, click the Details tab.

4. To start the flash update, click the Flash Update… button.

5. Select ‘30.001’ from the list of available updates.

6. Click Next >.

7. Follow the remaining screen prompts until the flash update procedure

completes and displays the new firmware revision (v30.001).

Use DriveExecutive

Follow these steps to used DriveExecutive to upgrade your firmware.

1. With the Flash Kit installed (see Install the Flash Kit on page 6), launch

DriveExecutive and go online (via EtherNet/IP, or a 1203-USB or

1203-SSS converter) with the drive.

2. In the DriveExecutive treeview, click on the PowerFlex 700S Phase II drive.

Then click the information icon as shown in Figure 2 - on page 4 to display

the Properties screen of the drive.

3. On the PowerFlex 700S Phase II Properties screen, click the Component

Details tab.

4. To start the flash update, click the Flash Update button.

5. Select the PowerFlex 700S Phase II drive from the list of available devices,

and click Next >.

6. Select ‘30.001’ from the list of available updates, and click Next >.

7. Follow the remaining screen prompts until the flash update procedure

completes and displays the new firmware revision (v30.001).

IMPORTANT This update may cause the drive parameters to revert to their default values. You may

want to save your configuration using DriveExplorer or the HIM CopyCat feature before

upgrading.

IMPORTANT This update may cause the drive parameters to revert to their default values. You may

want to save your configuration using DriveExecutive or the HIM CopyCat feature

before upgrading.

Rockwell Automation Publication 20D-RN047A-EN-P - October 2019

Using ControlFLASH and ControlFLASH Plus

For instructions on how to install ControlFLASH software and ControlFLASH

Plus™ software and upgrade your drive firmware by using these software tools, see

these publications:

•ControlFLASH Firmware Upgrade Kit User Manual, publication

1756-UM105

•ControlFLASH Plus Quick Start Guide Quick Start, publication

CFP-QS001

Use HyperTerminal

Follow theses steps to use HyperTerminal to upgrade your firmware.

1. With the Flash Kit installed (see Install the Flash Kit on page 6), launch

HyperTerminal and go online (via 1203-USB or 1203-SSS converter) with

the drive.

2. Press the Enter key until the main menu (Figure 3 - Main Menu) appears.

Figure 3 - Main Menu

3. In the main menu, press 3 to flash upgrade. Then press the number key

that corresponds to the “PowerFlex 700S 2” in the list, and press Y (for

Yes) to update the flash code. The terminal program will start displaying

the letter “C”. This signals the XMODEM protocol that the download

may proceed. You then have one minute to start the transfer.

4. Select Tr ans f er > S e nd Fi l e to display the Send File screen (Figure 4 - Send

File Screen).

ATTENTION: Risk of injury or equipment damage exists. When you perform a flash

update, the drive will fault if it is receiving control I/O from the adapter. Verify that the

drive has stopped safely or is receiving control

I/O from an alternate source before beginning a flash update.

Main Menu - Enter Number for Selection

1> Display Setup Parameters

2> Display Event Queue

3> Flash Upgrade

Rockwell Automation Publication 20D-RN047A-EN-P - October 2019

5. Click Browse and navigate to the flash file located in:

C:\ Program Files\ControlFLASH\0001\0078\004C

Figure 4 - Send File Screen

6. In the Select File to Send window list, click on the ‘700S2ap30_01.bin’ file.

Then click Open. This file name now appears in the Filename box in the

Send File screen.

7. In the Protocol box, select “Xmodem.”

8. Click Send.

A dialog box appears and reports the progress of the update. When it is

complete, the message “Flash Complete” appears. Press any key to

continue.

9. Press the Enter key to return to the main menu.

Important Keep the device powered for 15 seconds after the operation has completed or until the

adapter MOD status indicator starts flashing green.

TIP To cancel the flash update at any time, press CTRL-X.

Rockwell Automation Publication 20D-RN047A-EN-P - October 2019

New Features and

Enhancements

This firmware revision contains the following new features and enhancements.

New Parameters Added to Define a Ground Fault Detection Fault

This firmware revision adds parameters 294 [HiHp GrdFlt Pct] and 295 [HiHp

GrdFlt Dly]. These parameters can be used to define the threshold of drive

current and delay time for a Ground Fault Detection fault to occur in frame

9…14 PowerFlex 700S with Phase II Control drives.

New Testpoint Selections

New testpoint selections 14…18 have been added to parameter 1168 [MC TP3

Select] for Rockwell Automation internal diagnostic use only.

Corrected Anomalies

There are no corrected anomalies for this firmware revision.

Known Anomalies

This firmware revision contains the following known anomalies.

294 HiHp GrdFlt Pct

Determines the threshold of percent of drive rated current for ground fault detection. This

parameter is used for frame 9…14 drives only.

Note: This parameter was added for firmware version 30.001.

Default:

Min/Max:

Units:

25.0

25.0/45.0

295 HiHp GrdFlt Dly

Determines the time delay for the ground fault detection. This parameter is used for frame

9…14 drives only.

Note: This parameter was added for firmware version 30.001.

Default:

Min/Max:

Units:

200.0

200.0/1500.0

mSec

1168 MC TP3 Select

Enter a value to select Motor Control (MC) data displayed in Par 1169 [MC

TP3 Value]. Par 1168 [MC TP3 Select] and Par 1169 [MC TP3 Value] are

diagnostic tools you can use to view internal drive parameters.

Note: Options 14…18 were added for firmware version 8.001 for Rockwell

Automation internal use only.

Default:

Options:

0 =

1 =

2 =

3 =

4 =

5 =

6 =

7 =

8 =

9 =

10 =

11 =

12 =

13 =

14 =

15 =

16 =

17 =

18 =

VdsError

VdsRef

VdsFdbk

SlipGain

SlipGnMaxLim

SlipGnMinLim

SlipGainRtd

MaxSlipGain

MinSlipGain

KpTermSlipRg

IntgtrmSlpRg

P510Bit26

LatchedSlpGn

FltrdSlipGain

NoiseSum1

NoiseSum2

NoiseSum1max

NoiseSum2max

GFTimeAccum

Andere Handbücher für PowerFlex 700S

Inhaltsverzeichnis

Andere Allen-Bradley Gleichstromantrieb Handbücher

Allen-Bradley

Allen-Bradley PowerFlex 700H Betriebsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 23P Bedienungsanleitung

Allen-Bradley

Allen-Bradley Ultra1500 2092-DA1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 6000T Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1395 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 6000T Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 40 Bedienungsanleitung

Allen-Bradley

Allen-Bradley The PowerFlex 755 On-Machine Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 70 Enhanced Control Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 70 Bedienerhandbuch

Allen-Bradley

Allen-Bradley PowerFlex 6000 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1397 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 755 Bedienungsanleitung

Allen-Bradley

Allen-Bradley CX300 Bedienungsanleitung

Allen-Bradley

Allen-Bradley powerflex 700 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 700H Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1336 IMPACT Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 4 Gebrauchsanweisung

Allen-Bradley

Allen-Bradley PowerFlex Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 700S Bedienungsanleitung

Allen-Bradley

Allen-Bradley Series B Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 755T Bedienungsanleitung

Allen-Bradley

Allen-Bradley powerflex 700 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 25-JBAA Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Stücklistenhandbuch

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung