Allen-Bradley ArmorBlock MaXum 4 Bedienungsanleitung

Publication 1792D-IN017B-EN-P - September 2000

Installation Instructions

ArmorBlock MaXum 4 Input Module

Series B

(Cat. No. 1792D-4BV0D)

This ArmorBlock MaXumI/O module (Cat. No. 1792D-4BV0D) is a

stand-alone 24V dc I/O product which communicates via a

DeviceNetnetwork. The sealed housing of this module requires no

enclosure.

This model has 4 inputs. Inputs are 24V dc automatically configured

for PNP (sourcing) or NPN (sinking) devices. Diagnostic features

included are short circuit and open wire detection reported to the

point level. Local logic control has been added to the Series B version

of this product.

41455

2ArmorBlock MaXum 4 Input Module Series B

Publication 1792D-IN017B-EN-P - September 2000

Package Contents

Your package contains:

•1 ArmorBlock MaXum Module

•Installation Instructions

(Note: Cable bases are ordered and shipped separately.)

European Union Directive Compliance

If this product has the CE mark it is approved for installation within

the European Union and EEA regions. It has been designed and

tested to meet the following directives.

EMC Directive

This product is tested to meet Council Directive 89/336/EEC

Electromagnetic Compatibility (EMC) and the following standards, in

whole or in part, documented in a technical construction file:

•EN 50081-2 EMC - Generic Emission Standard, Part 2 -

Industrial Environment

•EN 50082-2 EMC - Generic Immunity Standard, Part 2 -

Industrial Environment

This product is intended for use in an industrial environment.

Low Voltage Directive

This product is tested to meet Council Directive 73/23/EEC Low

Voltage, by applying the safety requirements of EN 61131-2

Programmable Controllers, Part 2 - Equipment Requirements and

Tests.

For specific information required by EN 61131-2, see the appropriate

sections in this publication, as well as the following Allen-Bradley

publications:

•Industrial Automation Wiring and Grounding Guidelines For

Noise Immunity, publication 1770-4.1

•Automation Systems Catalog, publication B113

ArmorBlock MaXum 4 Input Module Series B 3

Publication 1792D-IN017B-EN-P - September 2000

Install Your ArmorBlock MaXum I/O Module

To install the module:

•Set the node address

•Mount the module to the cable base

•Connect the cord sets

•Communicate with the module

These steps are explained in more detail in the following

procedures.

Set the Node Address

Valid node addresses are 00 to 63.

Set the node address using the rotary switches, RSNetWorx for

DeviceNet, DeviceNetManager, or other software configuration

tool. Setting the switches between 64 to 99 lets the software have

address control.

Each module is shipped set for node address 63. The switches are

located on the underside of the module. The two switches are:

•MSD (most significant digit)

•LSD (least significant digit)

To reset the node address, use a small blade screwdriver to rotate the

switches. Line up the small black dot on the switch with the number

setting you wish to use.

The rotary switches are read at module power up only. Settings

between 64 and 99 cause the module to use the last valid node

address stored internally. Example: The last setting was 40. If a

change is made to 68, and then you power up, the address will

default to 40.

The module is equipped with AutoBaud detect. AutoBaud lets the

module read the settings already in use on your DeviceNet network

and automatically adjusts to follow those settings.

4ArmorBlock MaXum 4 Input Module Series B

Publication 1792D-IN017B-EN-P - September 2000

See the illustration of the node address below.

Install the Module

This module mounts to the following cable bases:

•1792D-CBFM for KwikLinkflat media installation

•1792D-CB12 for 12mm drop cable installation

•1792D-CB18 for round media trunk connection

•or other optional cable base assembly

IMPORTANT The cable base should already be installed. See

publication 1792D-IN009B-EN-P for information on

installing the cable base.

NODE ADDRESS

(00-63 PGM)

LSDMSD

012

Bottom View of Module

Example: Node Address is set at 62, see small black dots. 30703-M

ArmorBlock MaXum 4 Input Module Series B 5

Publication 1792D-IN017B-EN-P - September 2000

To install the module:

1. Position the module over the mounted cable base. Align the

three captive screws in the module with the accepting

receptacles in the base.

2. Tighten the screws with a torque of 8 inch-pounds to secure

the module to the base.

Note: Dimensions change according to the cable base and module

combination used.

IMPORTANT Proper alignment of the screws is necessary to

complete the connections between the module

contacts and the cable contacts.

Align the screws to

properly assemble

the module to the

base.

41517

2.7(68.6)

1.9 (48.26)

Cable Base

1792D-CBFM is used

for this example.

Assembled

dimensions in

(mm)

4.72 (120)

6ArmorBlock MaXum 4 Input Module Series B

Publication 1792D-IN017B-EN-P - September 2000

Connect the Input Cord Sets to the MaXum Module

This module uses 5 pin micro (12mm) style PCB mounted connectors.

Four micro caps cover the connectors on your module. Remove the

caps and connect your cables to the appropriate ports.

Use the micro caps to cover and seal unused ports. A Pinout diagram

for the connector is shown next.

Please refer to publication 889-5.0 for Rockwell Automation cables

and cord sets offerings.

IMPORTANT If the devices (sensors) connected to the input

connections require Class 2 power to operate, the

DeviceNet connections of this equipment must be

ATTENTION

•Make sure all connectors and caps are

securely tightened to properly seal the

connections against leaks and maintain IP67

requirements.

•For maximum noise immunity, input and

output cable return wires must be properly

terminated. When inputs and outputs are

connected in loopback, return wires should

be connected together.

•I/O cable length should be less than 30

meters.

41452

Input Micro-Connector

(View into Socket)

Pin 1 Sensor Source Voltage

Pin 2 Not Used

Pin 3 Return Logic Ground1

Pin 4 Input

Pin 5 Not Used

1. Logic Ground is approximately 0.4V above DeviceNet V-measured at the module.

ArmorBlock MaXum 4 Input Module Series B 7

Publication 1792D-IN017B-EN-P - September 2000

Input connectors for this module are shown below.

DeviceNet Cable

DeviceNet cables are described in the installation publications for the

cable base assembly of your choice. Refer to the following

publications:

•1792D-IN009B-EN-P ArmorBlock MaXum Cable Base

Installation Guide

•DN-6.7.2 DeviceNet Cable Planning and Installation Manual

Communicate With Your ArmorBlock MaXum Module

This ArmorBlock module’s I/O is exchanged with the master through

a poll, change-of-state, or cyclic connection.

The module produces or consumes data as follows:

Cyclic - allows configuration of the block as an I/O client. The block

will produce and consume its I/O cyclically at the rate configured.

Type of I/O Connections Consumes Produces

Cyclic 0 Byte 2 Bytes

Polled 0 Byte 2 Bytes

Change-of-State 0 Byte 2 Bytes

41461

Input 0

Input 1 Input 2

Input 3

Connector A

Connector B Connector C

Connector D

8ArmorBlock MaXum 4 Input Module Series B

Publication 1792D-IN017B-EN-P - September 2000

Polled - a master initiates communication by sending its polled I/O

message to the module. The 4 input module scans the inputs and

fault bits producing a response that reflects their status.

Change-of-state - productions occur when an input changes or a

fault condition occurs. If no input or fault condition change occurs

within the expected packet rate, a heartbeat production occurs. This

heartbeat production tells the scanner module that the module is alive

and ready to communicate.

Refer to the table below for the word/bit definitions.

The DeviceNet Network uses advanced network technology,

producer/consumer communication, to increase network

functionality and throughput. Visit our web site at http://

www.ab.com/networks for producer/consumer technology

information and updates.

Bit 0706050403020100

Produces0ISC-DISC-CISC-BISC-AI3I2I1I0

Produces 1 RSVD RSVD RSVD RSVD OW-D OW-C OW-B OW-A

Where: OW = Off Wire I = Input ISC = Input Short Circuit in Sensor Source

Voltage RSVD = Reserved

Byte Bit Description

Produces 0 00-03

04-07

Input status bits: When the bit is set (1), the input is on. Bit 00

= input 0, bit 01= input 1, bit 02 = input 2, bit 03 = input 3.

Sensor source voltage, input short circuit (ISC): Fault bits are

set (1) when the sensor source voltage is faulted. Bit 00 =

ISC-A on connector A, bit 01 = ISC-B on connector B, bit 02 =

ISC-C on connector C, bit 03 = ISC-D on connector D.

Produces 1 00-03

04-07

Off-Wire fault (OW): Bit 00 = OW-A on connector A, bit 01 =

OW-B on connector B, bit 02 = OW-C on connector C, bit 03 =

OW-D on connector D.

Reserved

ArmorBlock MaXum 4 Input Module Series B 9

Publication 1792D-IN017B-EN-P - September 2000

Troubleshoot with the Indicators

This module has the following indicators:

•Network/Module status indicator

•Logic status indicator

•Individual point status indicators

The following table describes network and module status indicators.

Net/Mod Status Indicator

indication Status:

Off No power or auto bauding

Flashing Green/Off On line but not connected

Solid Green On line, link OK, connected

Flashing Red Recoverable fault - module configuration error

I/O connection fault - one or more I/O connections in the timed-out

state

Solid Red Unrecoverable fault

Communication failure - duplicate node address present or incorrect

baud rate

Green to Red to Off At powerup only - LED test

41461

Connector A

Connector B Connector C

Connector D

Point indicator for

input 1

Point indicator for

input 0

Point indicator

for input 3

Point indicator

for input 2

LED Assignments

Module Status

Indicators

10 ArmorBlock MaXum 4 Input Module Series B

Publication 1792D-IN017B-EN-P - September 2000

The following table describes logic status indicators.

The following table describes I/O status indicators.

For more information on indications see the Technical Data

publication 1792-TD001B-EN-P.

Logic Status Indicators

State Status

Off Logic is disabled

Solid Green Logic is enabled

Flashing Green Local forces are applied and local logic is enabled

I/O Status Indicators

Function Module Status Indicator Point Indicator Condition

Inputs Green

Green

Module status blink red

None

Yellow

Red

Blink Red

No valid input

Valid input

Short on input connector

Off-wire on input connector

Inhaltsverzeichnis

Andere Allen-Bradley E/A-System Handbücher

Allen-Bradley

Allen-Bradley ArmorBlock LP2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2097-TB1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 1747-L511 Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 1746-NT8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1738-IR2M12 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Series B Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1797-IBN16 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-IGD Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-IA16I Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX Ex 1797-OB4D Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1492-CM1771-LD005 Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1762-IF2OF2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756 ControlLogix Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1762-IQ32T Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock MaXum 1792D-8BVT8D Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 1746-NR4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1719 Ex I/O Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-IV2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O 1794-IR8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IT8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley D Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley E300 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IB16D Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-OF8IH Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung