Allen-Bradley Flex integra 1793-IB16 Bedienungsanleitung

Artisan Technology Group is your source for quality

new and certied-used/pre-owned equipment

• FAST SHIPPING AND

DELIVERY

• TENS OF THOUSANDS OF

IN-STOCK ITEMS

• EQUIPMENT DEMOS

• HUNDREDS OF

MANUFACTURERS

SUPPORTED

• LEASING/MONTHLY

RENTALS

• ITAR CERTIFIED

SECURE ASSET SOLUTIONS

SERVICE CENTER REPAIRS

Experienced engineers and technicians on staff

at our full-service, in-house repair center

WE BUY USED EQUIPMENT

Sell your excess, underutilized, and idle used equipment

We also offer credit for buy-backs and trade-ins

www.artisantg.com/WeBuyEquipment

REMOTE INSPECTION

Remotely inspect equipment before purchasing with

our interactive website at www.instraview.com

LOOKING FOR MORE INFORMATION?

Visit us on the web at www.artisantg.com for more

information on price quotations, drivers, technical

specications, manuals, and documentation

View

Instra

FLEX I/O and FLEX Integra are trademarks

of Rockwell Automation Publication 1793-5.8 - December 1999

Installation Instructions

FLEX Integra

16 Sink Input Module

(Cat. No. 1793-IB16 and -IB16S)

Module Installation

This module mounts on a DIN rail. It connects to an adapter or another

FLEX I/O or Integra module. Note: If using this module with FLEX I/O

modules, do not mount between FLEX I/O modules. Mount Integra

modules to the right of the FLEX I/O modules. To mount this module:

1. Remove the cover plug (if used) in the male connector of the unit to

which you are connecting this module.

2. Position the module on the 35 x 7.5mm DIN rail A(A-B pt. no.

199-DR1).

3. Rotate the module onto the DIN rail with the top of the rail hooked

under the lip on the rear of the module.

30869-M

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

2FLEX Integra 16 Sink Input Module

Publication 1793-5.8 - December 1999

4. Press down to lock the module on the DIN rail.

If the module does not lock in place, use a screwdriver of similar

device to move the locking tab down, press the module flush with the

DIN rail and release the locking tab to lock the module in place.

5. Firmly push the module into the adjacent module/terminal base until

the units lock together.

6. Repeat the above steps to install the next module.

7. To remove an Integra module, you must work from the right side and

remove one module at a time. To disengage a module from its

neighbor, place a common flat-bladed screwdriver between the 2

modules and turn 1/4 turn to separate the modules.

8. Then slide the module away from its left neighbor, and release the

locking lever to remove the module from the DIN rail.

30870-M

30871-M

30872-M

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

FLEX Integra 16 Sink Input Module 3

Publication 1793-5.8 - December 1999

European Union Directive Compliance

If this product has the CE mark it is approved for installation within the

European Union and EEA regions. It has been designed and tested to meet

the following directives.

EMC Directive

This product is tested to meet Council Directive 89/336/EEC

Electromagnetic Compatibility (EMC) and the following standards, in

whole or in part, documented in a technical construction file:

• EN 50081-2 EMC - Generic Emission Standard, Part 2 - Industrial Environment

• EN 50082-2 EMC - Generic Immunity Standard, Part 2 - Industrial Environment

This product is intended for use in an industrial environment.

Low Voltage Directive

This product is tested to meet Council Directive 73/23/EEC Low Voltage,

by applying the safety requirements of EN 61131-2 Programmable

Controllers, Part 2 - Equipment Requirements and Tests.

For specific information required by EN 61131-2, see the appropriate

sections in this publication, as well as the following Allen-Bradley

publications:

• Industrial Automation Wiring and Grounding Guidelines For Noise Immunity,

publication 1770-4.1

• Automation Systems Catalog, publication B111

This equipment is classified as open equipment and must be mounted in an

enclosure during operation to provide safety protection.

ATTENTION: Do not remove this module under

power. Removing this module under power will break the

electrical backplane (flexbus) connections. This can cause

personal injury or property damage by:

• sending an erroneous signal to your system's field

devices causing unintended machine motion

• causing an explosion in a hazardous environment

• breaking communication to modules beyond this

module

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

4FLEX Integra 16 Sink Input Module

Publication 1793-5.8 - December 1999

Wiring

This module is available with 2 styles of terminations: 1793-IB16 -

screw-cage and 1793-IB16S - spring-clamp. Refer to the wiring figure

below.

1. Connect individual sensor signal input leads to terminals 0 through 15

on row A(channels 0 thru 15 respectively).

2. Connect the associated sensor power lead to +24V dc on row (B).

3. Connect +24V dc voltage to Vterminal on row B.

4. Connect 24V dc common to terminal COM on row A.

5. If daisy-chaining + 24V dc from this module to the next Integra

module, connect a jumper from terminal Vto terminal 8 on the next 8

point Integra module or terminal Von the next 16 point Integra

module.

6. If daisy-chaining 24V dc common from this module to the next FLEX

Integra module, connect a jumper from terminal COM on this module

to terminal 0 on the next 8 point Integra module, or to terminal COM

on the next 16 point Integra module.

ATTENTION: Total current draw through the module’s

(V) voltage terminals is limited to 10A. Separate power

connections to the module may be required.

01 2345678 9101112131415COM

COM

41816

012345 6789101112131415 A

41814

COM COM

1793-IB16

Where: COM = common, V = +24V dc power, 0 thru 15 = inputs

1793-IB16S

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

FLEX Integra 16 Sink Input Module 5

Publication 1793-5.8 - December 1999

Wiring Connections

Example of 2-wire and 3-wire Sensors

Channel Input Power Channel Input Power

connect to

corresponding

terminal on

row B

connect to

corresponding

terminal on row

11 99

2 2 10 10

3 3 11 11

4 4 12 12

5 5 13 13

6 6 14 14

7 7 15 15

+24V dc Power terminals V are internally connected together in the module.

24V dc

common

Common terminals COM are internally connected together in the

module.

01 2345678 9101112131415COM

COM

41818

2-Wire Sensor 3-Wire Sensor

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

6FLEX Integra 16 Sink Input Module

Publication 1793-5.8 - December 1999

Indicators

A= Status indicators - 0 through 15 - shows status of individual inputs

B= Insertable label for writing individual input designations

Memory Mapping

Bit/

Word 15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00

Read I15 I14 I13 I12 I11 I10 I9 I8 I7 I6 I5 I4 I3 I2 I1 I0

Write Reserved DT 12-15 DT 00-11

Where:I = Input

DT = delay time - refer to “Setting the Input Delay Time”

1793-IB16

0 1 2 3 4 5 6 7 8 9 10 11 14 1512 13

24 VDC SINK INPUT

41812

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

FLEX Integra 16 Sink Input Module 7

Publication 1793-5.8 - December 1999

Setting the Input Delay Time

You can select the input delay time (DT) for channels 00 thru 011, and

channels 12-15. Select the input delay time by setting the corresponding

bits in the output image table (complementary word) for the module.

For example, to set a delay time of 4ms for an input module at address rack

1, module group 0, set bits05, 04, 03, 02, 01 and 00 as shown below.

Input Delay Times

Important: Input and output wiring must be in accordance with Class I,

Division 2 wiring methods and in accordance with the

authority having jurisdiction.

02 01 00 Filter Time for Inputs 00-11 Selected

Filter Time

05 04 03 Filter Time for Inputs 12-15

000FilterTime0(default) 250

μs

001FilterTime1 500

μs

010FilterTime2 1ms

011FilterTime3 2ms

100FilterTime4 4ms

101FilterTime5 8ms

110FilterTime6 16ms

111FilterTime7 32ms

15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00

100= 44 Octal or 36 decimal

Write delay time on system startup.

Write DT to complement

of input module.

Fill File

Source

Destination

Length

#O:010

I:000

FLL

O:010

Dec.

41335B

100

DT 00-11

DT 12-15

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

8FLEX Integra 16 Sink Input Module

Publication 1793-5.8 - December 1999

C-UL and UL Hazardous Location Approval Approbation d’utilisation dans des

environnements dangereux par la C-UL and UL

C-UL and UL certifies products for general use as

well as for use in hazardous locations. Actual

C-UL and UL certification is indicated by the

product label as shown below, and not by

statements in any user documentation.

La C-UL and UL certifie des produits pour une

utilisation générale aussi bien que pour une

utilisation en environnements dangereux. La

certification C-UL and UL en vigueur est indiquée

par l'étiquette produit et non par des indications

dans la documentation utilisateur.

Example of the

C-UL and UL

certification

product label



Exemple

d'étiquette de

certificationd'un

produit par la

C-UL and UL



To comply with C-UL and UL certification for use

in hazardous locations, the following information

becomes a part of the product literature for this

C-UL and UL-certified industrial constrol product.

• This equipment is suitable for use in Class

I, Division 2, Groups A, B, C, D, or

non-hazardous locations only.

• The products having the appropriate C-UL

and UL markings (that is, Class I, Division 2,

Groups A, B, C, D) are certified for use in

other equipment where the suitability of

combination (that is, application or use) is

determined by the C-UL and UL or the local

inspection office having jurisdiction

• Peripheral equipment must be suitable for

the location in which it is used.

EPour satisfaire à la certification C-UL and UL en

environnements dangereux, les informations

suivantes font partie intégrante de la

documentation des produits de commande

industrielle certifiés.

• Cet équipement ne convient qu’à une

utilisation dans

des environnements de Classe I, Division 2,

Groupes A, B, C, D ou non dangereux.

• Les produits portant le marquage C-UL and

UL approprié (c'est-à-dire Classe I, Division

2, Groupes A, B, C, D) sont certifiés pour une

utilisation avec d'autres équipements, les

combinaisons d’applications et d’utilisation

étant déterminées par la C-UL and UL ou le

bureau local d'inspection.

• L'équipement périphérique doit convenir à

l'emplacement d'utilisation.

Important: Due to the modular nature of a

programmable control system, the

product with the highest temperature

rating determines the overall

temperature code rating of a

programmable control system in a Class

I, Division 2, location. The temperature

code rating is marked on the product

label as shown.

Important: De par la nature modulaire des systèmes de

commande programmables, le produit

ayant le code de température le plus élevé

détermine le code de température global du

système dans un environnement de Classe

I, Division 2. Le code de température est

indiqué sur l'étiquette produit.

7HPSHUDWXUHFRGHUDWLQJ &RGHGHWHPSpUDWXUH

The following warnings apply to products having

C-UL and UL certification for use in hazardous

locations.

Les avertissements suivants s'appliquent aux

produits ayant la certification C-UL and UL pour une

utilisation dans des environnements dangereux.

CUS

LISTED

CL I, DIV 2

GP A,B,C,D

TEMP

CUS

LISTED

CL I, DIV 2

GP A,B,C,D

TEMP

CL I, DIV 2

GP A,B,C,D

TEMP

Look for temperature

code rating here.

CUS

LISTED Le code de température

est indiqué ici.

CUS

LISTED

CL I, DIV 2

GP A,B,C,D

TEMP

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

FLEX Integra 16 Sink Input Module 9

Publication 1793-5.8 - December 1999

C-UL and UL Hazardous Location Approval Approbation d’utilisation dans des

environnements dangereux par la C-UL and UL

WARNING: Explosion Hazard

• Substitution of components may impair

suitability for Class I, Division 2.

• Do not replace components unless power

has been switched off or the area is known

to be non-hazardous.

• Do not disconnect equipment unless power

has been switched off or the area is known

to be non-hazardous.

• Do not disconnect connectors unless

power has been switched off or the area is

known to be non-hazardous. Secure any

user-supplied connectors that mate to

external circuits on this equipment by using

screws, sliding latches, threaded

connectors, or other means such that any

connection can withstand a 15 Newton (3.4

lb.) separating force applied for a minimum

of one minute.

• Batteries must only be changed in an area

known to be non-hazardous.

$9(57,66(0(175LVTXHGH[SORVLRQ



• La substitution de composants peut rendre ce

matériel inadapté à une utilisation en

environnement de

Classe I, Division 2.

• Couper le courant ou s'assurer que

l’environnement est classé non dangereux

avant de remplacer des composants.

• Couper le courant ou s’assurer que

l’environnement est classé non dangereux

avant de débrancher l'équipement.

• Couper le courant ou s'assurer que

l’environnement est classé non dangereux

avant de débrancher les connecteurs. Fixer

tous les connecteurs fournis par l'utilisateur

pour se brancher aux circuits externes de cet

appareil à l 'aide de vis, loquets coulissants,

connecteurs filetés ou autres, de sorte que les

connexions résistent à une force de séparation

de 15 Newtons (1,5 kg - 3,4 lb.) appliquée

pendant au moins une minute.

• S'assurer que l'environnement est classé non

dangereux avant de changer les piles.

C-UL and UL logo is a registered trademark of the

Underwriters Laboratories.

Le sigle C-UL and UL est une marque déposée de

la Underwriters Laboratories.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Allen-Bradley E/A-System Handbücher

Allen-Bradley

Allen-Bradley POINT I/O 1734-IE2C Bedienungsanleitung

Allen-Bradley

Allen-Bradley Compact 5000 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley C Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 1746-NR4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 750 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-OE2C Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-DA Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IM8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1791-32A0 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-IF6CIS Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1762-IF2OF2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Micro800 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756-OB16IS Benutzerhandbuch

Allen-Bradley

Allen-Bradley MicroLogix 1762-IQ32T Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-IA16I Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Bulletin 5370 CVIM Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IB8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Flex I/O Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1734-OE4C Bedienungsanleitung

Allen-Bradley

Allen-Bradley CompactBlock LDX 1790D-T4T0 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1769-ECL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756 ControlLogix Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung