Allen + Roth SUMTER 21-B461H-BN-AR Bedienungsanleitung

08-27-2020

ITEM # 2596143, 2596144

SINGLE HANDLE

BATHROOM FAUCET

MODELS 21-B461H-BN-AR,

21-B461H-ORB-AR, 21-B461H-CP-AR

Español p. 9

ALLEN + ROTH and logo design are

trademarks or registered trademarks of LF, LLC.

ATTACH YOUR RECEIPT HERE

Serial Number ___________________________ Purchase Date___________________________

Questions, problems, missing parts? Before returning to the store, call our customer

service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Sunday.

SM20278

SUMTER

PART DESCRIPTION QUANTITY PART DESCRIPTION QUANTITY

AFaucet body 1 D Deckplate 1

BPush pop-up drain assembly 1 E Gasket 1

C Allen wrench 1

Due to constant design and quality improvements, the product inside may look slightly different from the picture.

HARDWARE CONTENTS (not shown actual size)

AA BB CC

Washer Mounting nut Wrench

Qty. 1 Qty. 1 Qty. 1

PACKAGE CONTENTS

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install

the product.

CAUTION

• If you solder the joints during installation of the faucet, the seats, cartridges, and washers must be

removed before using a ame or the warranty will be voided on these parts.

• Cover the sink drain to avoid losing parts.

WARNING

• Protect your eyes with safety glasses when cutting or soldering water supply lines.

• NOTE: When making water line connections, HAND TIGHTEN. DO NOT OVERTIGHTEN. Do not

use PTFE pipe tape, plumber’s putty, pipe dope or any other type of sealing compound on water

inlet or threads. Additional compound is unnecessary. A watertight seal between the thread inlet

and supply tube is achieved by compression.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package

contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble

the product. Contact customer service for replacement parts.

Estimated Assembly Time: 30 minutes

Tools Required for Assembly (not included): Adjustable Wrench, Slip Joint Pliers, Pipe Wrench,

Phillips Screwdriver, and Silicone.

Installation may vary depending on how the previous faucet was installed. Supplies necessary for the

installation of the faucet are not all included; however, they are available wherever plumbing supplies

are sold.

Prior to beginning installation, turn off the hot and cold water lines, then turn on the old faucet to

release built-up pressure. When installing the new faucet, hand tighten the connector nuts. DO NOT

OVERTIGHTEN. Connections that are too tight will reduce the integrity of the system.

PRODUCT SPECIFICATIONS

Maximum ow rate: 1.2 GPM (4.54 LPM) at 60 PSI Total weight of item: 2.36 lbs.

ASME A112.18.1/CSA B125 Ceramic cartridge

NSF/ANSI 61 Manufactured to include no more than 0.25%

weighted average lead content on wetted

surfaces

Brushed nickel nish - 2596143

Oil-rubbed bronze nish - 2596144

Chrome nish - 21-B461H-CP-AR

INSTALLATION INSTRUCTIONS

1. Shut off the water at the supply valves under the sink or at the main water

supply. Disconnect the supply lines. Remove the existing faucet from the

sink.

Clean and dry the surface area where the new faucet will be mounted.

2. To install with the optional deckplate for a 3-hole sink, skip to Step 3.

Insert the water supply inlets (2.1) and mounting bolt (2.2) on the faucet body (A)

through the mounting hole in the sink (2.3). Skip to Step 4.

2.2

2.1 2.3

3. OPTIONAL DECKPLATE INSTALLATION:

Apply a thin bead of silicone to the gasket (E). Place the gasket (E) and

deckplate (D) over the mounting holes in the sink, aligning the center hole

in the gasket (E) and deckplate (D) with the center mounting hole in the sink

(3.1). Insert the water supply inlets and mounting bolt (3.2) on the faucet body (A)

through the hole in the deckplate (D) and the mounting hole in the sink (3.1)

until the faucet sits on top of the deckplate (D).

3.1

3.2

4. From underneath the sink, secure the faucet body (A) to the sink using the

metal washer (AA) and lock nut (BB). Tighten the lock nut (BB) with the

wrench (CC) provided.

Hardware used

AA Washer x 1

BB Mounting nut x 1

CC Wrench x 1

5. Remove the bottom gasket (5.1) and mounting nut (5.2) from the drain

assembly (B). Push the bottom gasket (5.1) down onto the top of the

mounting nut (5.2) and twist to attach together.

5.1

5.2

5.3

INSTALLATION INSTRUCTIONS (continued)

6. Insert the drain assembly (B) into the drain hole in the sink (6.1). Ensure the top

gasket (6.2) rests securely between the top of the sink and the top of the drain

assembly (B).

6.2

6.1

7. From underneath the sink, screw the bottom gasket (7.1) and mounting

nut (7.2) onto the drain assembly (B) by twisting until secure against the

bottom of the sink.

IMPORTANT: Remember to reconnect the drain body to the P-Trap drain

assembly (not included) before testing the faucet.

7.1

7.2

8. Attach the end of each integrated supply line (8.1) from the faucet body (A) to

the hot and cold water supply valves (8.2) under the sink, after making sure

the supply valves (8.2) are clear of any debris. Thread the nut on the end of

the integrated supply line (8.1) onto the outlet of the water supply valve (8.2)

and tighten with a wrench. Do not overtighten. NOTE: The hot side inlet tube is

indicated by a label.

NOTE: Do not use PTFE pipe tape, plumber's putty, pipe dope, or any other

type of sealing compound on the water inlets or threads. Additional compound

is not necessary. A watertight seal between the supply valve and the nut on the

integrated supply line is achieved by compression.

8.1

8.2

9. After installation is complete, turn on the water supply and adjust the handle

(9.1) on the faucet body (A) to the warm position where it mixes both hot and

cold water. Allow the water to run for a least one minute to ush away any

debris that could cause damage to the internal parts. While the water is running,

check for leaks. If leaks occur, gently tighten the nut on the connection that is

leaking. Fill the sink with water to check the drain for leaks. If water is leaking

from the drain, tighten the nut on the drain assembly. Turn off the water and

empty the sink.

9.1

10.1

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE SOLUTION

Faucet leaks underneath

handle. Bonnet has come loose or O-ring on cartridge

is dirty or twisted. 1. Move the handle to the OFF position.

Unscrew the handle screw and remove

the handle.

2. Tighten the bonnet by turning it clockwise.

Move the cartridge stem to the ON posi-

tion. The leak should stop draining out

from around the cartridge stem.

3. If the leak does not stop, shut off the water

supply. Remove the bonnet by turning it

counterclockwise. Lift out the cartridge

valve. Inspect the larger O-ring on the

cartridge bonnet and the smaller O-ring on

the cartridge stem. Remove any debris from

the O-rings. If either O-ring is twisted,

straighten it. If either O-ring is damaged,

replace the cartridge by calling customer

service.

4. Position the cartridge back into the faucet

body. Make sure the ridges on the two

sides of the cartridge bonnet t into the

grooves on the two sides of the faucet

body. Tightly screw the bonnet onto the

faucet body.

5. Reinstall the handle.

Water does not com-

pletely shut off. Rubber valve seat is dirty, stuck, or broken. 1. Shut off the water supply.

2. Remove the handle from the faucet body.

Loosen the bonnet by turning it counter-

clockwise. Lift out the cartridge assembly.

3. Inspect the rubber valve seat in the faucet

body. If there is debris or brass scrap on

the surface of the seat, remove it. If the

rubber seat is stuck tightly in the water

inlet hole, push it gently with a ngertip so it

moves up and down smoothly. The spring

(smaller end up) must be placed back

underneath the valve seat. If the rubber

valve seat is worn out or broken, replace the

cartridge by calling customer service.

4. Position the cartridge back into the faucet

body. Make sure the ridges on the two

sides of the cartridge bonnet t into the

grooves on the two sides of the faucet

body. Tightly screw the bonnet onto the

faucet body.

5. Reinstall the handle.

CARE AND CLEANING

Clean periodically with a soft cloth. Avoid abrasive cleaners, steel wool, and harsh chemicals as these will dull the nish

and void your warranty.

REPLACEMENT PARTS

For replacement parts, call our customer service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Sunday.

PART DESCRIPTION PART # PART # PART #

21-B461H-BN-AR 21-B461H-ORB-AR 21-B461H-CP-AR

1Handle RP13211BN RP13211ORB RP13211CH

2Set screw RP50002 RP50002 RP50002

3Connector RP50097 RP50097 RP50097

4Cap RP80551BN RP80551ORB RP80551CH

5Bonnet RP70539 RP70539 RP70539

6Cartridge RP20090 RP20090 RP20090

7Allen wrench RP70221 RP70221 RP70221

8Washer RP64258 RP64258 RP64258

9Lock nut RP56033 RP56033 RP56033

10 Wrench RP70771 RP70771 RP70771

11 Push pop-up drain

assembly RP40269BN RP40269ORB RP40269CH

12 Deckplate RP80287BN RP80287ORB RP80287CH

13 Gasket RP80288 RP80288 RP80288

Note: Appearance of actual parts may vary from drawing.

ROUGH-IN

6-3/8"

7-1/2"

2-3/8" 2-5/8"

5-5/8"

4-1/2"

2-1/2"

MAX.

LIMITED LIFETIME WARRANTY

The distributor warrants to the original consumer purchaser this product to be free from defects in material and workmanship

under normal use in residential applications. At its option, the Company will provide repair parts or replace defective product

when the product is used in accordance with the manufacturer’s specications.

The distributor provides a limited 5-year warranty on the nish of this product to the original purchaser. At its option, the

distributor will provide repair parts or replace defective product when the product is used in accordance with the manufacturer’s

specications. Use of mild abrasive, abrasive or chemical cleaners may damage the nish of the faucet. We recommend

cleaning your faucet with a soft cloth, moistened with water. Damage resulting from the use of abrasive or chemical cleaners

SHALL VOID THIS WARRANTY.

This warranty is not applicable to any products or parts of products where damage is caused by use of non-genuine parts; is

due to installation error, product misuse, negligence or faulty maintenance; or where the product is not installed according to

local building codes.

This warranty excludes labor charges or damage incurred during installation, repair or replacement, and any indirect, incidental

or consequential damages, losses, injury or costs of any nature. This warranty is in lieu of and excludes all other warranties,

conditions and guarantees, whether expressed or implied, including without restriction those of merchantability or tness of use.

Liability under this warranty will not exceed the purchase price for the product claimed to be defective by the original consumer

purchaser. Some states or provinces do not allow the exclusion or limitation of consequential damages so the above limitations

or exclusions may not apply. This warranty gives you specic legal rights and you may also have other rights which vary from

state to state, or province to province.

Inquiries regarding warranty claims can be directed to 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Sunday.

Printed in China

ARTÍCULO # 2596143, 2596144

GRIFO PARA BAÑO DE

UNA SOLA MANIJA

MODELOS 21-B461H-BN-AR,

21-B461H-ORB-AR, 21-B461H-CP-AR

ALLEN + ROTH y el diseño del logo son marcas

comerciales o marcas registradas de LF, LLC.

¿Preguntas, problemas, piezas faltantes? Antes de volver a la tienda, llame a nuestro

Departamento de Servicio al Cliente al 1-866-439-9800, de lunes a domingo de 8 a.m. a 8 p.m.,

hora estándar del Este.

ADJUNTE SU RECIBO AQUÍ

Número de serie _________________________ Fecha de compra ________________________

SUMTER

NSF/ANSI 61

SIN

PLOMO

CUMPLE

CON ADA

PARTE DESCRIPCIÓN CANTIDAD PARTE DESCRIPCIÓN CANTIDAD

ACuerpo del grifo 1 D Placa 1

BEnsamble desagüe

emergente a presión 1E Junta 1

CLlave Allen 1

Debido a las constantes mejoras de diseño y calidad, es posible que el producto en el interior se vea ligeramente diferente de la imagen.

ADITAMENTOS (no se muestran en tamaño real)

AA BB CC

Arandela Tuerca

de bloqueo Llave inglesa

Cant. 1 Cant. 1 Cant. 1

CONTENIDO DEL PAQUETE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Allen + Roth Sanitärprodukte Handbücher

Allen + Roth

Allen + Roth LWSG30VBR Bedienungsanleitung

Allen + Roth

Allen + Roth 67692W-6104 Bedienungsanleitung

Allen + Roth

Allen + Roth ML-20602R Bedienungsanleitung

Allen + Roth

Allen + Roth 67124W-6104 Bedienungsanleitung

Allen + Roth

Allen + Roth ML-20522 Bedienungsanleitung

Allen + Roth

Allen + Roth CAMERON 30MB Bedienungsanleitung

Allen + Roth

Allen + Roth 2889548 Bedienungsanleitung

Allen + Roth

Allen + Roth F121E413CP Bedienungsanleitung

Allen + Roth

Allen + Roth 67123W-6104 Bedienungsanleitung

Allen + Roth

Allen + Roth CAMERON 36MB Bedienungsanleitung

Allen + Roth

Allen + Roth 67131W-602707 Bedienungsanleitung

Allen + Roth

Allen + Roth ELIZA 71-BVF11-BN-AR Bedienungsanleitung

Allen + Roth

Allen + Roth 67746W-612707 Bedienungsanleitung

Allen + Roth

Allen + Roth 21-B45WDCP-AR Bedienungsanleitung

Allen + Roth

Allen + Roth FS1A9281CP Bedienungsanleitung

Allen + Roth

Allen + Roth YORKSHIRE 1412VA-30-201-925 Einrichtungshandbuch

Allen + Roth

Allen + Roth 67130W-602707 Bedienungsanleitung

Allen + Roth

Allen + Roth LWSJ60VBR Bedienungsanleitung

Allen + Roth

Allen + Roth 67095W-6204 Bedienungsanleitung

Allen + Roth

Allen + Roth LWSJ48VBR Bedienungsanleitung

Allen + Roth

Allen + Roth 67124W-6004 Bedienungsanleitung

Allen + Roth

Allen + Roth LWSG48VBR Bedienungsanleitung

Allen + Roth

Allen + Roth WSWS-PB1C Bedienungsanleitung

Allen + Roth

Allen + Roth 3074-02618-ARCH Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema