ALPA 5 Functions Bedienungsanleitung
Lingua originale: inglese REV. 1 - 10/20
5 Functions
metrology
ALPA_DIGITAL_INDICATOR_5FUNCTION
1. Contact point
3. Down lifting lever cover
5. Output connector
7. Battery compartment
(*selected by models)
2. Smooth lifting lever
4. LCD display
6. Lifting lever lid
8. in/mm Button
9. ON/OFF Button
10. ZERO Button
11. ABS/INCH Button
12. TOL Button
DESCRIPTION
6
5
12
3
2
4
108
7
11
9
1
EN
TECH DATA
Measuring range 0-12.5mm/0-0.5in 0-25mm/0-1in 0-50mm/0-2in 0-12.5mm/0-0.5in
Resolution
0.01mm/0.0005in 0.01mm/0.0005in 0.01mm/0.0005in 0.001mm/0.00005in
Total tolerance
±0.02mm ±0.03mm ±0.04mm ±0.015mm
Repeatability
0.01mm 0.01mm 0.01mm 0.003mm
Measurement force
≤1.6N ≤2.2N ≤3.5N ≤1.6N
Max. measurement speed
0,6m/s
Force hysteresis
≤0,5N
Operating temperature
0°C~+40°C
Storage temperature
10°C~+60°C
ALPA_DIGITAL_INDICATOR_5FUNCTION
OPERATING INSTRUCTIONS
Absolute Measurement: press the “ZERO” switch, Absolute ZERO is set completed. The indicator
is now ready for absolute measurement.
Relative Measurement: press “ABS/INC” switch at any position, RELATIVE ZERO is set, and the
indicator is now ready for relative measurement. Press “ABS/INC” again, the INC will disappear, the
indicator will turn to absolute measurement.
Metric/inch Conversion: metric/inch conversion will be made when pressing “in/mm” key at any
position.
The indicator features mm/inch conversion and zero setting at any position.
EN
OPERATING PRECAUTIONS
• Keep indicator face clean, prevent liquid from getting into inside
• Avoid shocks, impact, dropping etc, otherwise it will damage the
appearance and precision
• Do not operate indicator in direct sunlight. Do not store indicator in an
area of extreme high or cold temperature
• Donot connect anypart of digitalindicator with voltage,otherwise it will
damage the circuit
• Donotremoveendlidwithoutusingoutputinterface.Outputendshould
never be connected with metal. Doing so could damage your
indicator
• Use CR2025 (Lithium cell) battery
• Must take out of the battery if not in use for a long time
ALPA_DIGITAL_INDICATOR_5FUNCTION
BEFORE OPERATION
• Before using the indicator for the rst time, please wipe the rust
preventative oil on the indicator with a soft cloth
• Remove battery compartment lid and insert CR2025 battery with its
positive (+) side facing upward
EN
TROUBLESHOOTING
FAILURE POSSIBLE SITUATION SOLUTIONS
Five digits appear simultaneously and
change rapidly Battery power low Remove battery compartment lid and
replace battery
The display does not work(only when
changing battery)
Circuit accidental pause caused by poor
voltagewhenxingbattery
Remove battery
and replace it after 30 seconds
Nothing appears on the LCD Battery has poor contact
Battery voltage is under 2.5V
Keep good contact for battery or replace
the battery
The display is in disorder The measurement speed is too fast, more
than 0.6m/s
Keep the measurement speed less than
0.6m/s
ALPA_DIGITAL_INDICATOR_5FUNCTION
1 x battery 3V type CR2025
BATTERY CHANGE MAINTENANCE
Dry carefully all metallic parts of the instrument, clean it using
alcohol or petrol and then lubricate it with ne oil after water jets
or moisture effects to guarantee a good mechanical working and
to avoid rust.
Clean the housing and the display window using a soft chiffon and
neutral detergent. Do not use organic products (diluents, petrol,
acetone, etc…)
Don’t keep the instrument in the sun, heat or humidity.
EN
We certify that this instrument has been manufactured in accordance with our Quality Standard and
tested with reference to masters of certied traceability by the National Ofce of Metrology.
CERTIFICATE OF CONFORMITY
Because we make our instruments in batches, you may nd that the date on your calibration certicate
is not current. Please be assured that your instruments are certied at point of production and then
held in stock in our warehouse in accordance with our Quality Management System ISO 9001. Re-
calibration cycle should start from date of receipt.
CALIBRATION CERTIFICATE
ALPA_DIGITAL_INDICATOR_5FUNCTION
1. Punto di contatto
2. Asta scorrevole
3. Sede Asta scorrevole
4. Display LCD
5. Connettore Output
6. Supporto
7. Vano batteria
8. Pulsante in/mm
9. Pulsante ON/OFF
10. Pulsante ZERO
11. Pulsante ABS/INCH
12. Pulsante TOL
DESCRIZIONE
6
5
12
3
2
4
108
7
11
9
1
Inhaltsverzeichnis
Sprachen:
Andere ALPA Messgerät Handbücher
ALPA
ALPA MEGAline AA084 Bedienungsanleitung
ALPA
ALPA ABSolutus Bedienungsanleitung
ALPA
ALPA LITEsurf Bedienungsanleitung
ALPA
ALPA EA012 Bedienungsanleitung
ALPA
ALPA MEGAwhiz Bedienungsanleitung
ALPA
ALPA Exacto BA070 Bedienungsanleitung
ALPA
ALPA AA082 Bedienungsanleitung
ALPA
ALPA MEGAtower Bedienungsanleitung
ALPA
ALPA MEGAline Bedienungsanleitung
ALPA
ALPA MEGArod Bedienungsanleitung
