Altinex MT104-100/103 Bedienungsanleitung

MULTI-TASKER™

MANUAL PART NUMBER: 400-0082-005

MT104-100/103

6-IN, 1-OUT VIDEO SWITCHER

CARD FOR MULTI-TASKER™

USER’S GUIDE

MULTI-TASKER™

400-0082-005 1

TABLE OF CONTENTS

Page

PRECAUTIONS / SAFETY WARNINGS.............. 2

GENERAL..........................................................2

INSTALLATION .................................................2

CLEANING.........................................................2

FCC /CE NOTICE..............................................2

ABOUT YOUR MT104-100/103............................ 3

TECHNICAL SPECIFICATIONS .......................... 3

DESCRIPTION OF MT104-100 ............................ 4

APPLICATION DIAGRAMS................................... 5

DIAGRAM1: RGBHV CONFIGURATION...........5

DIAGRAM2: C-VIDEO CONFIGURATION ........6

DIAGRAM3: INTERNAL VIEW ..........................7

INSTALLING YOUR MT104-100........................... 8

OPERATION.......................................................... 8

RS-232 CONTROL.............................................8

DESCRIPTION OF COMMANDS.......................8

SUMMARY OF COMMANDS ...........................17

MENU MODE...................................................17

TROUBLESHOOTING GUIDE............................20

LED IS NOT ON...............................................20

LED IS BLINKING RED....................................20

NO DISPLAY....................................................21

ALTINEX POLICY................................................ 21

LIMITED WARRANTY/RETURN POLICY........21

CONTACT INFORMATION..............................21

MULTI-TASKER™

400-0082-005 2

PRECAUTIONS / SAFETY WARNINGS 1

Please read this manual carefully before using your

MT104-100/103. Keep this manual handy for future

reference. These safety instructions are to ensure

the long life of your MT104-100/103 and to prevent

fire and shock hazard. Please read them carefully

and heed all warnings.

1.1 GENERAL

•Qualified ALTINEX service personnel, or their

authorized representatives,must perform all

service.

1.2 INSTALLATION

•To prevent fire or shock, do not expose this unit

to rain or moisture. Do not place the

MT104-100/103 in direct sunlight, near heaters

or heat radiating appliances, or near any liquid.

Exposure to direct sunlight, smoke, or steam

can harm internal components.

•Handle the MT104-100/103 carefully. Dropping

or jarring can damage the card.

•Do not pull the cables that are attached to the

MT104-100/103.

•Insert the card carefully into the slots of the

Multi-Tasker™ without bending any edges.

•When removing a card, please make sure that

the card to which it is attached is also pulled out

simultaneously.

1.3 CLEANING

•Clean only the connector area with a dry cloth.

Never use strong detergents or solvents, such

as alcohol or thinner. Do not use a wet cloth or

water to clean the card. Do not clean or touch

any component or PCB.

1.4 FCC / CE NOTICE

•This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) This device may not cause

harmful interference, and (2) this device must

accept any interference received, including

interference that may cause undesired

operation.

•This equipment has been tested and found to

comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference when the

equipment is operated in a commercial

environment. This equipment generates, uses,

and can radiate radio frequency energy and, if

not installed and used in accordance with the

instruction manual, may cause harmful

interference to radio communications. Operation

of this equipment in a residential area is likely to

cause harmful interference in which case the

user will be required to correct the interference

at their expense.

•Any changes or modifications to the unit not

expressly approved by ALTINEX, Inc. could void

the user’s authority to operate the equipment.

MULTI-TASKER™

400-0082-005 3

ABOUT YOUR MT104-100/103 2

MT104-100 & MT104-103

6-in 1-out MT Switcher Cards

The MT104-100 and MT104-103 are 6-in 1-out

Video Switcher Cards. These MT Video SW cards

enable 6 composite video sources to be connected

and switched to a single display or recording

device. The MT104-100 can be used together with

one or two Video SW Expansion Cards for up to 22

inputs. See the MT104-101 product sheet for more

information.

Multiple MT Video SW series cards can be installed

into a Multi-Tasker™enclosure to provide

additional functionality. For example, two MT Video

SW cards can be used to handle the two

components of an S-Video signal (Chroma and

Luma). In order to create a component video

switcher, simply install three of the MT Video SW

cards, one each for the Y, Pr, and Pb (or Y, R-Y,

B-Y) signal components. Similarly, the MT Video

SW series cards can also be used to pass

computer video signals: 4 cards for RGBS and 5

for RGBHV.

The MT Video SW cards utilize solid state

switching technology, and offer the ability to pass

VGA thru UXGA high-resolution video signals

without degradation. Inputs are selected via easy-

to-use ASCII commands from a control system or

computer connected to the RS-232 port of a

Multi-Tasker™ enclosure. Also available through

ASCII control is “on-off” output control.

Additionally, by special order you can have VIS

(Vertical Interval Switching) capability added. This

is a feature that eliminates the "glitch" normally

associated with composite video switching.

TECHNICAL SPECIFICATIONS 3

FEATURES/

DESCRIPTION MT104-100/103

GENERAL

Inputs

External Connectors (6) BNC Female (Analog

Video or TTL Sync)

Internal Connectors (2) 10-pin IDC Connectors

Outputs

Output Connector (1) BNC Female (Analog

Video or TTL Sync)

Capability

Using 1 Card Composite Video

Using 2 Cards S-Video (Y/C)

Using 3 Cards Component Video, RGsB,

& RsGsBs

Using 4 Cards RGBS

Using 5 Cards RGBHV, VGA thru UXGA*

Approvals CE/FCC

Expandability

MT104-100 Up to 2expansion cards.

MT104-103 Not expandable

Table 1. MT104-100/103 General

MECHANICALMT104-100/103

Enclosure Slots Required One

Weight 0.43lb (0.19kg)

Shipping Weight 1 lb. (0.45kg)

Connector Panel Black

T° Operating 10°C to 40°C

T° Storage 0°C to 50°C

Humidity 90% non-condensing

MTBF (calc.) 55,000 hrs

Table 2. MT104-100/103 Mechanical

*Adapter required. See Table 3, Optional Accessories.

MULTI-TASKER™

400-0082-005 4

ELECTRICALMT104-100/103

Input Signals

Analog +/-1.5V (1.5Vp-p)

Or Digital +5V

Impedance 75 Ohms

Type Differential

Return Loss -38dB @ 50MHz

Maximum DC Offset 10mV

Output Signals

Gain 1.05 (+/-5%)

Impedance 75 Ohms

Propagation Delay (Sync) 4nS max.

Rise/Fall time (Sync) 6nS max.

Differential Phase Error 01° @ 4.5 MHz

Power

from MT100-100 +6V -6V Power

Consumption

MT104-100 100mA 80mA 1.1 watts

MT104-103 125mA 90mA 1.3 watts

Optional Accessories

MS8102CA 6ft., 15-pin HD Male to 5 BNC

Male

MS8112CA 6ft., 15-pin HD Female to 5

BNC Male

Table 3. MT104-100/103 Electrical

DESCRIPTION OF MT104-100 4

MULTI-TASKER™

400-0082-005 5

Use the MT104-100/103 card for RGBHV switching. One card is needed for each channel, for a total of 5

Video SW Cards: one card for R, one card for G, one card for B, one card for H and one card for V.

Connect IN 1 of the R signal card to the R signal from a laptop, video camera, etc. IN 2 will be connected to

the R signal of a Macintosh, document camera, etc. Continue this sequence for each card and signal.

Connect the VID OUT of the R signal card to the R signal from the projector. The same applies to the

G, B, H & V signals. Note: to group multiple cards, see the MT100-100 user's guide for more information.

APPLICATION DIAGRAMS 5

DIAGRAM 1: RGBHV CONFIGURATION

MULTI-TASKER™

400-0082-005 6

DIAGRAM 2: C-VIDEO CONFIGURATION

MULTI-TASKER™

400-0082-005 7

6IN 1 OUT BNC SW + SIGNAL DETECT + EXPANDABLE + OUTPUT DISABLE

DIAGRAM 3: INTERNALVIEW

6IN 1 OUT BNC SW + OUTPUT DISABLE

MULTI-TASKER™

400-0082-005 8

INSTALLING YOUR MT104-100 6

Step 1. Slide the MT104-100/103 into an available

slot in the Multi-Tasker™ Enclosure in

order to connect to the bus. Make sure

that the MT104-100/103 card fits into

place. Secure the card to the

Multi-Tasker™ by tightening the retainer

screws located on the top and bottom of

the MT104-100/103 card.

Step 2. The LED on the card panel will turn red

indicating that the card is in full operation.

An LED that is blinking red indicates that

the card is experiencing a problem. If the

LED is blinking, see Troubleshooting

Guide in section 8. On the MT104-100, a

green LED indicates that a signal is

present.

Step 3. Connect a coaxial cable from the video

source to the input connector of the

MT104-100/103. Connect the output

connectors of the MT104-100/103 to the

display devices through a coaxial cable.

Step 4. Starting from the left, identify the slot

number where the MT104-100/103 card is

plugged into the Enclosure and note that

it is for RS-232 control.

OPERATION 7

7.1 RS-232 CONTROL

When used in the Multi-Tasker™ Enclosure, the

MT104-100/103 has many advanced remote

control capabilities, which are accessible through

standard RS-232 communication. The actual

controlling can be accomplished through a

computer control system or any other device

capable of sending RS-232 commands.

7.1.1 RS-232 INTERFACE

The RS-232 commands, for the

MT104-100/103, are in a simple ASCII character

format.

1. Square brackets “[ ]” are part of the

command.

2. Use uppercase letters for all commands.

After processing a command, an OK or ER will

be returned as feedback if "F" is included at the

end of a command string.

Commands ending in "S" will be saved into

memory. Commands not ending in "S" will still

be executed but will not be restored when the

system is reset or powered OFF then ON.

7.2 DESCRIPTION OF COMMANDS

Each command consists of three parts:

Function, Card ID, and Unit ID.

[Function , Card ID , Unit ID ]

Example: [VERC3U2]

VER = Function

C3 = Card ID or Group ID

U2 = Unit ID

For Function, see a detailed explanation under

each command description.

MULTI-TASKER™

400-0082-005 9

The Card ID is an assigned value. It is equal to

the enclosure slot number in which the card is

installed. The value can range from 1 to 4 up to

1 to 20 depending on the enclosure.

Card ID 0 (C0) is used for the controller. See

the MT100-100 User’s Guide for details.

The Group ID is a number representing a group

of cards defined with the [WR] command. When

using the Group ID, all cards in the group will

perform the given instruction.

Changing the position of a card will significantly

affect the commands recorded on software

definitions or third party control systems.

The Unit ID has a value from 0 to 9. Unit ID 0

should be used for single unit operation. If the

Unit ID is set to zero, each command may be

used without Ui. Use the command [SETU0],

as explained in the MT100-100 User’s Guide.

Example:

[VERC3]: For Unit ID Zero

[VERC3Ui]: For Unit ID other than Zero

[VERC3]: Equivalent to [VERC3U0]

1. [VER]

This command receives the software version

and card type for the MT104-100/103 card.

Command Format: [VERCnUi]

Cn = card ID (n = # from 1 to max slots)

Ui = Unit ID (i = # from 0 to 9)

Example:

There is one MT104-100/103 card is in slot #2

of unit 3. Send the command [VERC2U3], and

the Multi-Tasker™ Enclosure will return:

MT104-100690-0158-004

MT104-100= card type

690-0158-004 = software version

2. [C]

This command receives the status of the card.

Command Format: [CnUi]

Cn = Card ID (n = # from 1 to max slots)

Ui = Unit ID (i = # from 0 to 9)

Example:

There is one MT104-100 card in slot #4.

Sending the command [C4] to the

Multi-Tasker™ will yield the following feedback:

ON 4 C04

ON 4 = Output 4 is selected and enabled

C04 = The card is in slot 4

If there is no card in slot #4, sending the [C4]

command will not return any feedback.

3. [CnS]

This command saves the current status of the

card. This configuration will be restored after

system is reset or powered off then on.

Cn = card number (n = #1 to max slots)

S = save configuration

If Input 1 is enabled, the feedback after sending

the command [C4S], for slot 4, would be:

ON:1 C04 Saved

4. [?]

This command will return general information

about the Multi-Tasker™ and cards installed in

the unit.

Command Format: [?Ui]

Cn = Card ID (n = # from 1 to max slots)

Ui = Unit ID (i = from 0 to 9)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Altinex Schalten Handbücher

Altinex

Altinex UT260-102 Bedienungsanleitung

Altinex

Altinex MX2414RM Bedienungsanleitung

Altinex

Altinex MX2456RM Bedienungsanleitung

Altinex

Altinex MX2222AT Bedienungsanleitung

Altinex

Altinex MX2106AV Bedienungsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

Altinex

Altinex MT304-203 Bedienungsanleitung

Altinex

Altinex MX2106AV Bedienungsanleitung

Altinex

Altinex MULTI-TASKER MT104-108 Bedienungsanleitung

Altinex

Altinex MX2216RM Bedienungsanleitung

Altinex

Altinex Tilt 'N Plug Interconnect Box TNP100-HB Bedienungsanleitung

Altinex

Altinex Furniture Mount Interconnect Box... Bedienungsanleitung

Altinex

Altinex MX2100AV Bedienungsanleitung

Altinex

Altinex MULTI-TASKER MT104-102 Bedienungsanleitung

Altinex

Altinex MX2406RM Bedienungsanleitung

Altinex

Altinex MX430-101 8x8 Bedienungsanleitung

Altinex

Altinex MX2214RM Bedienungsanleitung

Altinex

Altinex MX2426CV Bedienungsanleitung

Altinex

Altinex SW1956CT Bedienungsanleitung

Altinex

Altinex DA1916SX Bedienungsanleitung

Altinex

Altinex MX2436RM Bedienungsanleitung

Altinex

Altinex Universal Tilt 'N Plug Interconnect Box... Bedienungsanleitung

Altinex

Altinex MULTI-TASKER MT104-107 Bedienungsanleitung

Altinex

Altinex SW104-130 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung