Altronix Trove2M2R Bedienungsanleitung
Trove2M2R
Trove rack enclosure with
Altronix and Mercury Backplane (TM2R)
Access & Power Integration
Rev. 122222
Installing Company: _______________ Service Rep. Name: __________________________________
Address: _____________________________________________ Phone #: __________________
More than just power.TM
Installation Guide
All registered trademarks are property of their respective owners.
SIGNALING
- 2 - Trove2M2R Installation Guide
Overview:
Altronix Trove2M2R rack mount access & power integration solution consists of a high-capacity rack enclosure with
removable backplane. This unit easily accommodates various combinations of Mercury boards with or without Altronix
power supplies and accessories in a streamlined package for access systems.
Specifications:
Agency Listings:
• UL 294 - 7th edition. Trove2R Access Control Sub-Assemblies: Destructive Attack I.
• CE European Conformity.
Trove2M2R
Trove2R rack mount enclosure with TM2R Altronix/Mercury backplane.
• 16 Gauge black enclosure with ample knockouts for convenient access.
• Modular 2U standard EIA 19” drawer with extendable slides up to 48”.
• Dimensions (H x W x D): 3.375” x 19.0” x 33.25” (85.8mm x 482.6mm x 844.6mm).
• Includes tamper switch (Altronix Model TS112 or equivalent) and cam lock.
TM2R
Altronix/Mercury backplane.
• 16 Gauge backplane.
• Dimensions (H x W x D): 32” x 14.3” x 0.3125” (812.8mm x 363.2mm x 7.9mm).
Optional Accessories:
• RE2: Rack Mount Battery Enclosure accommodates up to four (4) 12VDC/7AH batteries
• WM5, WM25, WM100: Magnetic Cable Tie Mounts (5, 25, 100 counts).
• LC3: 6 ft. three-wire line cord.
Backplane Accommodates a Combination of the Following:
Altronix:
• One (1) eFlow4NB, eFlow6NB, eFlow102NB, eFlow104NB,
AL400ULXB2, AL600ULXB, AL1012ULXB, AL1024ULXB2,
ACMS8(CB) or ACM8(CB).
• Up to two (2) ACM4(CB), MOM5, PD4UL(CB), PD8UL(CB), PDS8(CB), or VR6.
Mercury:
• Up to four (4) LP1502, LP4502, MR52, MR16IN, MR16OUT.
• One (1) LP2500, MUX8.
• One (1) Genetec Cloudlink.
Hardware and Accessories:
Spacer | 5/16” Pan Head Screw | Lock Nut
Trove2M2R Installation Guide - 3 -
Installing Trove2R into Rack Tower:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local
codes and authorities having jurisdiction. These products are for indoor use only and must be installed within
the protected premises.
Note: First assemble and Install Z Bracket Wire Management Accesory
(refer to Z Bracket Installation pg. 4)
1. Remove backplane from enclosure prior to installing into rack cabinet
(do not discard hardware).
2. In order to mount included cUL Listed tamper switch (Tane Model 3/8 ASH FM WH
or equivalent) turn the enclosure upside down and locate mounting holes
(Fig. 1, pg. 3). Insert the tamper switch flying leads into the center knockout of
the three (3) holes from outside of thedrawer with the button facing outwards,
make sure tamper switch is inserted properly then secure it with the two (2)
screws (supplied). Connect tamper switch wiring to the Access Control Panel
input or the appropriate UL Listed reporting device.
To activate alarm signal open the rack drawer.
3. Slide the rack enclosure into an open 2U location in the four post rack cabinet.
4. Utilizing proper fasteners attach front ears to the rack rails (Rack drawer, pg. 8).
5. Attach the rear of the adjustable slides to the rear rails of the rack cabinet with the proper fasteners.
6. Secure the rack cover (Fig. 2a, pg. 3) and rack drawer (Fig. 2b, pg. 3) to earth ground.
7. Ensure that all internal cofigurations (voltage selection, switch settings, etc.) are completed before
mounting backplane back into Trove rack enclosure.
Fig. 2
Fig. 2a
Fig. 2b
Fig. 1
Back of the drawer,
viewed from outside.
Tamper Switch
mounting location
- 4 - Trove2M2R Installation Guide
Z Bracket Installation for Trove2R:
Altronix Trove2R enclosure includes Z Bracket, a convenient and reliable wire management accessory.
Hardware (included):
Twelve (12) bolts and eight (8) lock nuts.
1. Carefully unpack Z Bracket. Do not discard hardware
(included) (Fig. 3, pg. 4).
2. Attach arms to each other using bolts and
lock nuts (Fig. 4a, pg. 4).
3. Attach the hinge brackets to the ends of
arms using bolts and nuts positioning
them as shown on (Fig. 4b, pg. 5).
4. Make sure that all nuts are tightened.
5. Attach the hinge bracket on each end of Z Bracket, then attache the Z Bracket to the adjustable slide
using bolts and lock nuts
(included) (Fig. 5, 5a, pg. 4).
6. Attach the hinge bracket on the shorter side of Z Bracket to the rear of the rack enclosure using bolts
(included).
Fig. 5
Fig. 5a
Fig. 4b
Fig. 3
Fig. 4a
Fig. 4
Fig. 3b
Trove2M2R Installation Guide - 5 -
TM2R:
Configuration of Altronix Power Supply and/or Sub-Assembly Boards and Mercury Boards
1. Fasten spacers onto metal pems configuration of backplane depending on the board (Fig. 6, pg. 5).
2. Position module over corresponding spacers and fasten screws into spacers (Fig. 6a, 6b, pg. 5).
3. Mount backplane to enclosure with hardware.
Position Chart for the Following Models:
Altronix / Mercury Pem Mounting
AL400ULXB2, AL600ULXB, AL1012ULXB, AL1024ULXB2,
eFlow4NB, eFlow6NB, eFlow102NB, eFlow104NB A
ACM8(CB), ACMS8(CB), ACMS12(CB), LINQ8ACM(CB) B
ACM4(CB), LINQ8PD(CB), PDS8(CB), PDS16(CB), VR6 C
LP1502, LP4502, MR52, MR16IN, MR16OUT D
LP2500, MUX8 E
Genetec Cloudlink F
D
A
BC
C
C
F E
D
D D
Fig. 6
Pem
Spacer
Backplane
Power Supply
or
Sub-Assembly
Pan Head Screw
Fig. 6a
Pem
Spacer
Backplane
Pan Head Screw
Mercury Board
Fig. 6b
- 6 - Trove2M2R Installation Guide
Notes:
Trove2M2R Installation Guide - 7 -
TM2R Backplane Dimensions (H x W x D):
3.375” x 19.0” x 33.25” (85.8mm x 482.6mm x 844.6mm)
14.3” (363.2mm)
32” (812.8mm)
- 8 - Trove2M2R Installation Guide
Trove2R Enclosure Dimensions:
3.375” x 19.0” x 33.25” (85.8mm x 482.6mm x 844.6mm). Shown with Z Bracket attached.
39.76” (1,001mm)
33.6” (853.4mm)
4.2” (106.7mm)
11.2” (284.5mm)
0.52” (13.2mm)
0.63” (16mm)
15.05” (382.3mm)
4.5” (114.3mm)
5.35” (135.9mm)
0.72”
(18.3mm)
15.14” (384.4mm)
1.5”
(38.1mm)
Altronix is not responsible for any typographical errors.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056
IITrove2M2R L22V MEMBER
Inhaltsverzeichnis
Andere Altronix Gehäuse Handbücher
Altronix
Altronix Trove Trove2KA2 Bedienungsanleitung
Altronix
Altronix Trove Series Bedienungsanleitung
Altronix
Altronix TROVE T1RAG3F8 Bedienungsanleitung
Altronix
Altronix THN2 Bedienungsanleitung
Altronix
Altronix Trove1BL1R Bedienungsanleitung
Altronix
Altronix T2MK3F4D Bedienungsanleitung
Altronix
Altronix Trove T1SAK34 Bedienungsanleitung
Altronix
Altronix Trove T1MK1F4V Bedienungsanleitung
Altronix
Altronix TROVE T1DMK3F4 Bedienungsanleitung
Altronix
Altronix Trove Series Bedienungsanleitung
Altronix
Altronix Trove T1PHK1F4S Bedienungsanleitung
Altronix
Altronix TROVE T3MK75F16 Bedienungsanleitung
Altronix
Altronix Trove T1RSH3F8 Bedienungsanleitung
Altronix
Altronix Trove T1RSH3F8 Bedienungsanleitung
Altronix
Altronix TROVE T2MK3F4 Bedienungsanleitung
Altronix
Altronix RE2 Bedienungsanleitung
Altronix
Altronix TROVE T2MK3F4D Bedienungsanleitung
Altronix
Altronix TROVE Trove1PD1 Bedienungsanleitung
Altronix
Altronix Trove1V1R Bedienungsanleitung
Altronix
Altronix Trove2AG2 Bedienungsanleitung
