American DJ Accu Wash 250 Bedienungsanleitung

American DJ®

4295 Charter Street

Los Angeles CA. 90058

www.americandj.com

Rev. 7/06

User Instructions

American DJ® - www.americandj.com - Accu Wash 250™ Instruction Manual Page 2

American DJ®

Accu Wash 250™

Table of Contents

Unpacking......................................................................3

Introduction....................................................................3

Customer Support......................................................................3

Safety Precautions......................................................................4

Handling Precautions..................................................................5

Discharge Lamp Warnings..........................................................5

Registration......................................................................6

Features.........................................................................6

Controls and Functions..............................................................7

Set-Up.............................................................................10

System Menu............................................................................13

Editing Program.........................................................................26

Operating Modes.......................................................................29

Fuse and Lamp Replacement...................................................31

DMX Traits.................................................................................33

Cleaning..................................................................35

Trouble Shooting.......................................................................35

Warranty.................................................................36

Specifications....................................................................39

Unpacking: Thank you for purchasing the Accu Wash 250™ by

American DJ®. Every Accu Wash 250™ has been thoroughly tested and

has been shipped in perfect operating condition. Carefully check the

shipping carton for damage that may have occurred during shipping.

If the carton appears to be damaged, carefully inspect your ﬁxture for

any damage and be sure all equipment necessary to operate the unit

has arrived intact. In the event damage has been found or parts are

missing, please contact our toll free customer support number for fur-

ther instructions. Please do not return this unit to your dealer without

contacting customer support ﬁrst.

Introduction: The Accu Wash 250™ is a seven channel, moving

head, intelligent DMX fixture. The fixture can operate in three different

operating modes; stand alone, sound-active, or in a Master/Slave con-

figuration. The Accu Wash 250™ comes with several built in programs

and is best used in multiples of four. When used as a stand alone unit

or when used in multiples linked in a master/slave configuration. For

best results use fog or special effects smoke to enhance the beams

projections.

During the initial start-up or use of this product a light smoke or

smell may arise from the unit. This is a normal process and is

cause by the heat associated with the lamp.

Customer Support: American DJ® provides a toll free customer

support line, to provide help and to answer any question should you

encounter problems during your set up or initial operation. You may

also visit us on the web at www.americandj.com for any comments or

suggestions. Service Hours are Monday through Friday 9:00 a.m. to 5:

00 p.m. Paciﬁc Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2610

E-mail: [email protected]

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or ﬁre, do

not expose this unit to rain or moisture.

Warning! This may cause severe eye damage. Avoid looking directly

into the light source at all times!

Accu Wash 250™ General Information

For Your Own Personal Safety, Please Read and Understand This

Manual Completely Before You Attempt To Install Or Operate

This Unit!

• To reduce the risk of electrical shock or ﬁre, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt-

age for your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken.

• Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and ﬁre in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they MODE/ESC from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 38 for cleaning details.

• Heat -This fixture should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including

amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. Objects have fallen, or liquid has been spilled into the appliance.

B. The appliance has been exposed to rain or water.

C. The appliance does not appear to operate normally or exhibits a

marked change in performance.

Accu Wash 250™ Safety Precautions

American DJ® - www.americandj.com - Accu Wash 250™ Instruction Manual Page 4American DJ® - www.americandj.com - Accu Wash 250™ Instruction Manual Page 3

American DJ® - www.americandj.com - Accu Wash 250™ Instruction Manual Page 5

Accu Wash 250™ Discharge Lamp Warning

This fixture is fitted with a discharge lamp which

is highly susceptible to damage if improperly

handled. Never touch the lamp with your bare fin-

gers as the oil from your hands will shorten lamp

life. Also, never move the fixture until the lamps

have had ample time to cool. Remember, lamps

are not covered under warranty conditions.

• Micro-Stepping Motors for Smooth Color and Gobo Transitions

• DMX-512 Protocol Compatible (Uses Seven DMX Channels)

• 7 Colors, Plus White - With Rainbow

• 3 Operating Modes - Master/Slave; Stand Alone; Sound Active

• Internal Microphone

• ZB-MSD250 Discharge Lamp, 230v/250w

• Edit and Save Scenes into the Memory

• Variable Strobe

• 360˚ Pan Movement

• 265˚ Tilt Movement

• Digital Display for Address and Function Setting

Accu Wash 250™ Features

The Accu Wash 250™ carries a one year limited warranty. Please fill

out the enclosed warranty card to validate your purchase. All returned

service items whether under warranty or not, must be freight pre-paid

and accompany a return authorization (R.A.) number. The R.A. number

must be clearly written on the outside of the return package. A brief

description of the problem as well as the R.A. number must also be

written down on a piece of paper and included in the shipping carton.

If the unit is under warranty, you must provide a copy of your proof of

purchase invoice. You may obtain a R.A. number by contacting our

customer support team on our toll free customer support number. All

packages returned to the service department not displaying a R.A.

number on the outside of the package will be returned to the shipper

at the shippers cost.

Accu Wash 250™ Product Registration

American DJ® - www.americandj.com - Accu Wash 250™ Instruction Manual Page 6

To optimize the performance of this product, please read these operating

instructions carefully to familiarize yourself with the basic operations of

this unit. These instructions contain important safety information regard-

ing the use and maintenance of this unit. Please keep this manual with

the unit, for future reference.

Accu Wash 250™ General Instructions

This unit emits intense UV radiation which is harmful to the eyes and

skin. The intense luminance of the lamp can cause severe damage

to the retina. Never operate this unit without it’s covers, these covers

have been specially designed to shield against UV radiation.

Epileptic Warning: Those suffering from epilepsy should avoid looking

directly into the lamp at all times.

Avoid switching the ﬁxture on and off repeatedly in short intervals as

this will reduce lamp life and intensity.

To achieve the intensity associated with discharge lamps, these lamps

use gas sealed in a high pressure environment to emit a brilliant output.

Due to the high pressure involved with the construction of the lamp,

the lamp may explode during prolonged extensive use. This risk is

increased with age, added care is encouraged when dealing with older

lamps. Extreme caution should be used when operating this or any

ﬁxture ﬁtted with a gas discharge lamp. Never open this unit while in

use.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures

warranty. In the unlikely event your unit may require service please

contact American DJ®.

During operation the housing may become extremely hot. Avoid

touching the unit with bare hands while in use.

American DJ® will not accept any liability for any resulting damages

caused by the non-observance of this manual or any unauthorized

modiﬁcation to this unit.

Accu Wash 250™ Handling Precautions

American DJ® - www.americandj.com - Accu Wash 250™ Instruction Manual Page 8American DJ® - www.americandj.com - Accu Wash 250™ Instruction Manual Page 7

Accu Wash 250™ Controls and Functions

REAR

FRONT

Accu Wash 250™ Controls and Functions

1. Digital Display - This display shows the menu and operating func-

tions that you can choose from.

2. MODE/ESC Button - This button is used to exit menus and to

scroll backwards through certain menus.

3. Up Button - This button is used to scroll forward when navigating

through the system menu.

4. Down Button - This button is used to scroll backwards when navi-

gating through the system menu.

5. ENTER Button - This button is used to select and conﬁrm a func-

tion when working in the system menu.

6. Carrying Handles - The includes built-in carrying handles. Be sure

to always handle the unit by the built-in handles. Never lift or carry-

ing the unit by head or yoke. Pulling on or transporting the unit by the

moving head may severely damage the unit and will void the unit war-

ranty.

7. XLR Output Jack - This jack is used to transmit the incoming

DMX signal to another DMX ﬁxture, or transmit a Master/Slave signal

to the next Accu Wash 250™ in the chain. For best results in DMX or

Master/Slave mode terminate this jack if it is the last unit in the chain.

See “Terminator” on page 11.

8. XLR DMX Input Jack - This jack is used to receive an incoming

DMX signal or Master/Slave signal.

9. MINI/C Controller Jack - This jack is for use with the optional

MINI/C controller only. This controller is used to control the blackout

function. Do not attempt to connect an audio signal to this jack, this

will damage the PC board and void your manufactures warranty!

10. Cooling Fan - This unit is equipped with three high velocity vari-

able fans to aid in the cooling process. These fans are designed to

vary their velocity at different operating temperatures, to provide

better cooling when the unit reached higher operating temperatures

associated with long usage. Be sure to never obstruct the cooling fans

during normal usage. Also, be sure to keep the vents clean at all times.

A blocked or malfunctioning cooling system may shorten lamp life and

unit reliability.

2 3 4 5 6 7 8 9

Accu Wash 250™ Controls and Functions

American DJ® - www.americandj.com - Accu Wash 250™ Instruction Manual Page 9

11. Lamp Assembly and Access Plate - This plate accesses the lamp

socket assembly. The unit includes a spring mounted ZB-MSD250

230v/250w discharge lamp. Be sure to only replace with same type

lamp. After replacing a lamp be sure the lamp is centered in the reﬂec-

tor. See page 32 for details on installing and optimizing replacement

lamps. Never operate this unit with the lamp exposed, this lamp emits

strong UV radiation.

12. Fuse Holder - This housing stores a 10 amp (5 amp 220v) GMA

protective fuse. Never defeat the fuse, the fuse is designed to pro-

tect the electronics in the event of severe power ﬂuctuations. Always

be sure to replace the fuse with an exact match as the one being

replaced, unless otherwise told to do so by an authorized American

DJ® service technician.

13. Power Cord Inlet - This unit is equipped with a removable I.E.C.

power cord. Be sure to only use the power cord included with the

unit, this cord is designed to match the electrical requirements of the

unit. Other cords may cause the unit to overheat or malfunction. Volt-

age may vary from venue to venue, when connecting this unit to a

power supply be sure to connect to a matching power outlet. Never

use this ﬁxture if the ground prong has been removed or broken off.

The ground prong is designed to reduce the risk of ﬁre or electrical

shock in the event the unit suffers from an internal short.

American DJ® - www.americandj.com - Accu Wash 250™ Instruction Manual Page 10

Power Supply: Before plugging your unit in, be sure the source volt-

age in your area matches the required voltage for your American DJ®

Accu Wash 250.™ The American DJ® Accu Wash 250™ is available

in a 120v and 220v version. Because line voltage may vary from venue

to venue, you should be sure your unit voltage matches the wall outlet

voltage before attempting to operate you ﬁxture. Also be sure to only

use the included I.E.C. power cable supplied with the unit, this cable

matches the voltage and current requirements of the unit.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used by most lighting and controller manufactures as a form of

communication between intelligent fixtures and controllers. A DMX

controller sends DMX data instructions from the controller to the fix-

ture. DMX data is sent as serial data that travels from fixture to fixture

via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX

fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models

of different manufactures to be linked together and operate from a

single controller, as long as all ﬁxtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using

several DMX fixtures try to use the shortest cable path possible. The

order in which fixtures are connected in a DMX line does not influence

the DMX addressing. For example; a fixture assigned a DMX address

of 1 may be placed anywhere in a DMX line, at the beginning, at the

end, or anywhere in the middle. Therefore, the first fixture controlled

by the controller could be the last fixture in the chain. When a fixture

is assigned a DMX address of 1, the DMX controller knows to send

DATA assigned to address 1 to that unit, no matter where it is located

in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX

and Master/Slave Operation): The Accu Wash

250™ can be controlled via DMX-512 protocol.

The Accu Wash 250™ is a seven channel DMX

unit. The DMX address is set electronically using

the controls on the side panel of the unit. Your

unit and your DMX controller require a standard 3-

pin XLR connector for data input and data output

(Figure 1). If you are making your own cables, be sure to use standard

Accu Wash 250™ Set Up

Figure 1

two conductor shielded cable (This cable may be purchased at almost

all professional sound and lighting stores). Your cables should be made

with a male and female XLR connector on either end of the cable. Also

remember that DMX cable must be daisy chained and cannot be split.

American DJ® - www.americandj.com - Accu Wash 250™ Instruction Manual Page 11

Accu Wash 250™ Set Up

Notice: Be sure to follow ﬁgures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Conﬁguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin XLR

connectors for DATA transmission in place of 3-pin. 5-pin XLR ﬁxtures

may be implemented in a 3-pin XLR DMX line. When inserting stan-

dard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be

used, these adaptors are readily available at most electric stores. The

chart below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Pin 5 - Do Not Use

Pin 4 - Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Accu Wash 250™ Set Up

American DJ® - www.americandj.com - Accu Wash 250™ Instruction Manual Page 12

Accu Wash 250™ System Menu

American DJ® - www.americandj.com - Accu Wash 250™ Instruction Manual Page 14American DJ® - www.americandj.com - Accu Wash 250™ Instruction Manual Page 13

Accu Wash 250™ System Menu

ADDRESS MENU -

VALU (Value) - This is for setting the DMX address of the unit.

TEST MENU -

T-01 - T-XX - Tests the functions of each channel. There are eight

channels, but only channels 1,2,3,4, and 6 can be tested.

AUDIO MENU -

ALON (Alone) - Unit runs in stand alone mode, no master/slave.

MSTR (Master) - Designates that unit to be master in master/

slave, sound active mode.

LAMP -

LAMP - Switches the lamp “On” or “Off”.

RESET MENU-

ALL (All) - Resets the unit.

SCAN (Scan) - Resets the pan/tilt motor.

COLR (Color) - Resets the color wheel motor.

SHTR (Shutter) - Resets the shutter motor.

TIME MENU -

LIFE - Displays the total ﬁxture running time.

LAMP - Displays the lamp running time.

CLMP - Clears the lamp running time.

REVERSE PAN -

RPAN (Reverse Pan) - Reverses the pan.

REVERSE TILT -

RTILT (Reverse Tilt) - Reverses the tilt.

DISPLAY MENU -

VALU (DMX-512 Value) - Display the DMX-512 value of each

channel.

D ON (Display On) - Turns the display off after 2 minutes.

FLIP (Reverse Display) - “Flips” the digital display 180º.

SPECIAL MENU -

LAAU - Lamp on with power.

RDMX - Lets you adjust the DMX address via external controller.

See pages 23-24.

DLDF - With this function you can adjust the lamp via the con-

trol board. In this mode the device will not react to any control

signal.

DLAY - Lamp delay time.

SPDT - Lamp adjustment.

DFSE - Restores default settings.

FEED - With this function you can activate or deactivate the

pan/tilt error correction. If your units head gets knocked out of

place the unit will automatically go back to the last setting.

VER - Displays the software version.

EDIT MENU -

STEP (Step) - Steps to be used in Edit Programming. See ediit

program. See pages 26-28.

SCO1 - SC30 (Scene 01 - Scene 30) - These are the scene slots

that you write your programs into. See edit program, pages 26-

28.

RUN - Run your preset program

2. Tap the UP button until “TEST” is displayed, press ENTER.

4. The display will show “T-01”, this means that your are now

testing channel 1. If you press UP till “TE-3” is displayed, the

unit will test the color channel, changing the color one by one

and also showing the rainbow effect with different speeds.

5. Press MODE/ESC to exit.

AUDI MAIN MENU -

MSTR With the function “MSTR”, you can designate a unit

to be the master in a sound active, master/slave conﬁgura-

tion

1. Access the main menu.

2. Tap the UP button until “AUDI” is displayed, press ENTER.

3. Tap the UP button until “MSTR” is displayed, press ENTER.

4. “PASS” should display quickly.

5. Press MODE/ESC to return to the main menu.

ALON With the function “ALON”, you can run the unit in

stand alone, sound active mode

1. Access the main menu.

2. Tap the UP button until “AUDI” is displayed, press ENTER.

3. Tap the UP button until “ALON” is displayed, press ENTER.

4. “PASS” should display quickly.

5. Press MODE/ESC to return to the main menu. The menu

must display “SO-A”

LAMP MAIN MENU -

LAMP With this function you can switch the lamp on or off

Accu Wash 250™ System Menu

On-Board System Menu.

The Accu Wash 250™ comes with an

easy to navigate system menu. This next section will detail the func-

tions of each command in the system menu.

Enter Button -

To access the main menu locate the ENTER button (5)

on the side of the unit. Press this button to activate the system menu.

Tap the UP button (3) until you reach function you wish to change.

When you reach the function you wish to change tap the ENTER

button. When a function is selected the menu will begin to ﬂash, use

the UP button to change the function. Once your changes are made

tap the ENTER button again to lock the change in the system, and

press the MODE/ESC button until your reach the beginning of system

menu (A001). If the ENTER button is not selected within eight seconds

the system will automatically return to menu section. To exit without

making any changes tap the MODE/ESC button (2).

Accu Wash 250™ System Menu

American DJ® - www.americandj.com - Accu Wash 250™ Instruction Manual Page 16American DJ® - www.americandj.com - Accu Wash 250™ Instruction Manual Page 15

MODE MAIN MENU -

ADDR DMX Address Setting via control board -

1. Access the main menu by pressing the ENTER button.

2. “ADDR” should now be displayed. Press ENTER.

3. “A001” should be displayed. Adjust the DMX address by

pressing the UP or DOWN buttons.

4. Press ENTER to conﬁrm. “PASS” will ﬂash for a few seconds

and then “A001” will be displayed again.

5. Press the MODE/ESC button to return to the main menu.

When the display is on “A001”, you can directly press the UP

or DOWN buttons to change the DMX start address.

TEST MAIN MENU -

TEST - This will test the functions of each channel.

1. Access the main menu.

American DJ® - www.americandj.com - Accu Wash 250™ Instruction Manual Page 18

Accu Wash 250™ System Menu

American DJ® - www.americandj.com - Accu Wash 250™ Instruction Manual Page 17

Accu Wash 250™ System Menu

via the control board.

1. Access the main menu.

2. Tap the UP button until “LAMP” is displayed, press ENTER.

3. The display will show “ON. If you want turn the lamp off,

press the DOWN button to display “OFF”.

4. Press ENTER to conﬁrm.

5. Press MODE/ESC to return to the main menu.

RESE MAIN MENU -

ALL - When you activate this reset function, the ﬁxture will

reset all motors and return the ﬁxture to the default set-

tings.

1. Access the main menu.

2. Tap the UP button until “RESE” is displayed, press ENTER.

3. “ALL” should be displayed

4. Press ENTER to reset or MODE/ESC to return to the main

menu..

SCAN - When you activate this reset function, the ﬁxture

will reset the pan/tilt motors only.

1. Access the main menu.

2. Tap the UP button until “RESE” is displayed, press ENTER.

3. Tap the UP button until “SCAN” is displayed.

4. Press ENTER to reset or MODE/ESC to return to the main

menu.

COLR - When you activate this reset function, the ﬁxture

will reset the color wheel motor only.

1. Access the main menu.

2. Tap the UP button until “RESE” is displayed, press ENTER.

3. Tap the UP button until “COLR” is displayed.

4. Press ENTER to reset or MODE/ESC to return to the main

menu.

SHTR - When you activate this reset function, the ﬁxture

will reset the shutter/dimmer motor only.

1. Access the main menu.

2. Tap the UP button until “RESE” is displayed, press ENTER.

3. Tap the UP button until “SHTR” is displayed.

4. Press ENTER to reset or MODE/ESC to return to the main

menu.

TIME MAIN MENU -

LIFE - With this function you can display the running time

of the unit. Check this out!

1. Access the main menu.

2. Tap the UP button until “TIME” is displayed, press ENTER.

3. “LIFE” should be displayed, press ENTER.

4. The display shows “XXXX”, “X” stands for the number of

hours.

5. Press ENTER or MODE/ESC to return to the main menu.

LAMP - With this function you can display the running time

of the lamp.

1. Access the main menu.

2. Tap the UP button until “TIME” is displayed, press ENTER.

Accu Wash 250™ System Menu Accu Wash 250™ System Menu

American DJ® - www.americandj.com - Accu Wash 250™ Instruction Manual Page 20American DJ® - www.americandj.com - Accu Wash 250™ Instruction Manual Page 19

3. Tap the UP button until “LAMP” is displayed, press ENTER.

4. The display shows “XXXX”, “X” stands for the number of

hours.

5. Press ENTER or MODE/ESC to return to the main menu.

CLMP - With this function you can clear the running time of

the lamp. Note Very Important: Please clear the lamp time

every time you replace the lamp.

1. Access the main menu.

2. Tap the UP button until “TIME” is displayed, press ENTER.

3. Tap the UP button until “CLMP” is displayed

4. Press ENTER to clear the running time, or MODE/ESC to

return to the main menu.

RPAN MAIN MENU -

RPAN - The movement of the Pan will be reversed.

1. Access the main menu.

2. Tap the UP button until “RPAN” is displayed, press ENTER.

3. The display will show “ON/OFF”.

4. Press the UP button to select “ON” to activate this function,

or “OFF” to deactivate this function.

5. Press ENTER to conﬁrm.

6. Press MODE/ESC to return to the main menu.

RTILT MAIN MENU -

RTILT - The movement of the Tilt will be reversed.

1. Access the main menu.

2. Tap the UP button until “RTILT” is displayed, press ENTER.

3. Press ENTER, the display will show “ON/OFF”.

4. Press the UP button to select “ON” to activate this function,

or “OFF” to deactivate this function.

5. Press ENTER to conﬁrm.

6. Press MODE/ESC to return to the main menu.

DISP MAIN MENU -

VALU Display the DMX-512 value of each channel -

1. Access the main menu.

2. Tap the UP button until “DISP” is displayed, press ENTER.

3. Tap the UP button until “VALU” is displayed, press ENTER.

4. The display should show “D-00”. Press the UP button in

order to select the desired channel. If you select “D-05” the

display will only show the DMX value of the 5th channel

5. Press ENTER to conﬁrm.

6. Press MODE/ESC to return to the main menu.

Now the display will change as per the 5th channel DMX

value.

D ON Shuts off digital display after 2 minutes.

1. Access the main menu.

2. Tap the UP button until “DISP” is displayed, press ENTER.

3. Tap the UP button until “D ON” is displayed, press ENTER.

4. The display will show “ON/OFF”. Press the UP button to

select “ON” to activate this function, or “OFF” to deactivate this

Inhaltsverzeichnis

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ Color Fusion Bedienungsanleitung

American DJ

American DJ Trance Wheel 250 Bedienungsanleitung

American DJ

American DJ H2O LED Bedienungsanleitung

American DJ

American DJ TRI GEM LED Bedienungsanleitung

American DJ

American DJ Starball II Bedienungsanleitung

American DJ

American DJ Color Shot Bedienungsanleitung

American DJ

American DJ Micro Phase Bedienungsanleitung

American DJ

American DJ Quadra Force/Sys Bedienungsanleitung

American DJ

American DJ DJ Roller Bedienungsanleitung

American DJ

American DJ Eco UV Bar DMX Bedienungsanleitung

American DJ

American DJ Fan-1000 Bedienungsanleitung

American DJ

American DJ Ruby Royal Bedienungsanleitung

American DJ

American DJ Mighty Scan Bedienungsanleitung

American DJ

American DJ Fusion Scan 250 Bedienungsanleitung

American DJ

American DJ SWEEPER BEAM LED Bedienungsanleitung

American DJ

American DJ Accu Spot 250 Hybrid Bedienungsanleitung

American DJ

American DJ Micro Moon Bedienungsanleitung

American DJ

American DJ FLASHBACK 4 Bedienungsanleitung

American DJ

American DJ Mini Flame LED Bedienungsanleitung

American DJ

American DJ Mini Mine Bedienungsanleitung

American DJ

American DJ LED Messenger Bedienungsanleitung

American DJ

American DJ SS-DMX19CTM Bedienungsanleitung

American DJ

American DJ Crystal Bedienungsanleitung

American DJ

American DJ Spherion Tri LED Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung