American DJ DJ Roller Bedienungsanleitung

User Instructions

American DJ®

©American DJ Supply®- www.americandj.com - DJ Roller™ Instruction Manual Page 2

Customer Support:

American DJ®provides a toll free customer support line, to provide set

up help and to answer any question should you encounter problems

during your set up or initial operation. You may also visit us on the web

at www.americandj.com for any comments or suggestions. For service

related issue please contact American DJ®. Service Hours are Monday

through Friday 9:00 a.m. to 5:00 p.m. Paciﬁc Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2610

E-mail: [email protected]

Warning! To prevent or reduce the risk of electrical shock or ﬁre, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

your nearest American DJ dealer.

PLEASE do not discard the shipping carton in the trash. Please

recycle when ever possible.

Safety Issues: This unit may blow a fuse if the maximum allotted

load of 15 amps is reached. If the fuse needs replacement, always

replace the fuse with same exact type that was remove, unless

otherwise instructed by an authorized American DJ®service techni-

cian. Use of a different type fuse from that which is recommended may

cause fire or electric shock and will void the manufactures warranty.

DJ Roller™ Unpacking

DJ Roller™ Introduction

Thank you for purchasing the DJ Roller™ by American DJ®. Every DJ

Roller™ has been thoroughly tested and has been shipped in perfect

operating condition. Carefully check the shipping carton for damage

that may have occurred during shipping. If the carton appears to be

damaged, carefully inspect your unit for any damage and be sure all

equipment necessary to operate the system has arrived intact. In the

event damage has been found or parts are missing, please contact our

toll free customer support number for further instructions. Please do not

return the unit to your dealer without ﬁrst contacting customer support.

American DJ

4295 Charter Street

Los Angeles, CA 90058

www.americandj.com

©American DJ Supply®- www.americandj.com - DJ Roller™ Instruction Manual Page 4©American DJ Supply®- www.americandj.com - DJ Roller™ Instruction Manual Page 3

DJ Roller™ Quick Start

The DJ Roller™ features a bright 150 watt/500 hour lamp life halogen

bulb with a separate gobo and color wheel. The color wheel features

seven brilliant colors plus white and the gobo wheel features 9 gobos

plus a large and small spot. This units is ready to be installed or hung

and powered right out of the box. There is no assembly required. This

fixture incorporates the use of high quality stepper motors for a more

accurate mirror movement. Mirror movement allows for a full 90

degree tilt (vertical) and a full 90 degree pan (horizontal). An internal

built in microphone allows the fixtures to run in Stand Alone mode so

there is no need for an external controller. The DJ Roller™ may also

be set-up to run in a Master-Slave mode when used in multiples, up to

16 units. When used in the Master-Slave mode, the unit will chase to

several internal programs. The DJ Roller™ can also be controlled via

a standard DMX controller such as the American DJ Show Designer,™

or the American DJ®DMX Operator,™ giving the user independent

control over the gobo and color wheel as well as the mirrors pan and

tilt movements.

• ZB-JCR/H5 15V/150W, 500Hr Lamp.

• DMX-512 Compatible.

• Stepper motors for smooth movements.

• 7 colors plus white.

• 10 Gobos plus spot.

• Master/Slave Operation

• Built-in microphone.

• Sound sensitivity knob.

• One year warranty.

• Sound Active.

• Optional MINI/C controller, for blackout control.

DJ Roller™ Features

Master/Slave Quick Start Stand Alone Mode

Connect up to four units together via XLR cables. The master unit

will run the slaves to the masters built in programs and internal

microphone. Plug in all units. When the DJ Roller™ is first turned on,

it will run through an internal self test where it resets all motors to their

zero position. After the self test the units will react to sound, and chase

to the several built in programs.

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required voltage

for your unit.

• Do not attempt to operate this unit if the power cord has been frayed

or broken. Please route your power cord away from foot trafﬁc.

• Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and ﬁre in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the top cover under any conditions. There are no

user serviceable parts inside.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit if it becomes damaged in any way.

• Never operate this unit when it’s cover is removed.

• To reduce the risk of electrical shock or ﬁre, do not expose this unit

rain or moisture

• This unit is intended for indoor use only, use of this product outdoors

voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-Cord Protection -Power-supply cords should be routed

so that they are not likely to be walked on or pinched by items

placed upon or against them, paying particular attention to cords at

plugs, convenience receptacles, and the point where they exit from

the fixture.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer.

• Heat -The fixture should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances (includ-

ing amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the appliance.

C. The appliance has been exposed to rain or water.

D. The fixture does not appear to operate normally or exhibits a

marked change in performance.

DJ Roller™ Safety Precautions

Power Supply: Before plugging your unit in be sure the source volt-

age in your area matches the required voltage for your American DJ®

DJ Roller.™ The American DJ®DJ Roller™is available in a 120v and

220v version. Because line voltage may vary from venue to venue,

you should be sure your unit voltages matches the wall outlet voltage

before attempting to operate you ﬁxture.

Data Cable (DMX Cable) Requirements

(For DMX Operation Only and Master-

Slave): The DJ Roller™ may be controlled via

DMX-512 protocol. Your unit and your DMX con-

troller require a standard 3-pin XLR connector

for data input and data output (Figure 1). If you

are constructing your own cables, be sure to

use standard two conductor shielded cable as

detailed in ﬁgure two (This cable may be pur-

chased at almost all pro sound and lighting stores). Your cables should

be made with a male and female XLR connector on either end of the

cable. Also remember that DMX cable must be daisy chained and may

not be split.

Notice: Be sure to follow ﬁgure three when making your own cables.

Do not use the ground lug on the XLR connector. Do not connect the

cable’s shield conductor to the ground lug or allow the shield conductor

to come in contact with the XLR’s outer casing. Grounding the shield

could cause a short circuit and erratic behavior.

DMX +

DMX -

COMMON

DMX512 IN

CONNECTOR

3 PIN

DMX512 OUT

CONTROLLER

CONNECTOR

3 PIN

©American DJ Supply®- www.americandj.com - DJ Roller™ Instruction Manual Page 5

DJ Roller™ Set Up

Figure 2

DJ Roller™ Set Up

©American DJ Supply®- www.americandj.com - DJ Roller™ Instruction Manual Page 6

1 Ground 1 Ground

XLR Male Socket XLR Pin Conﬁguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Figure 3

Figure 1

DJ Roller™ DMX Addressing

Special Note: Line Termination. When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number ZDMX/T) will decrease the possibilities of erratic

behavior.

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture. Figure 4

DMX is short for Digital Multiplex. This is a universal binary language

used as a form of communication between intelligent fixtures. Each

dip switch represents a binary value.

Dip Switch 1 address equals 1

Dip Switch 2 address equals 2

Dip Switch 3 address equals 4

Dip Switch 4 address equals 8

Dip Switch 5 address equals 16

Dip Switch 6 address equals 32

Dip Switch 7 address equals 64

Dip Switch 8 address equals 128

Dip Switch 9 address equals 256

Each dip switch has a preset value, a desired DMX address is set by

combining the dip switches that will create your desired value. For

example: To achieve a DMX address of 21, combine dip switches 1, 3,

and 5. Sense dip switch 1 has a value of 1, dip switch 3 has a value

of 4, and dip switch 5 has a value of 16, the combination of the create

a DMX value of 21.

Set DMX address 21: Set DMX address 201:

Dipswitches # 1 = 1 Dipswitches # 1 = 1

3= 4 4 = 8

5= 16 7 = 64

= 21 8 = 128

= 201

DMX CHANNEL

123 547986

1 4 16 64 256

2 8 32 128

Page 13 “Master Slave Dip Switch Settings”).

7. Please follow the chart on page 13 for all slave dipswitch settings.

Note only one fixture may use the master units dip switch settings

(see Page 13).

8. After all the units settings have been set and are plugged in, adjust

the sensitivity knob on the bottom of the master unit to make them

react to sound.

9. You can also use the optional MINI/C Remote Control. If you want

to use the optional remote control, connect the MINI/C controller

to the first fixture in the line (master). Note: The remote control

only operates in Stand-Alone and Master/Slave modes. If the

remote is connected in DMX mode it will not function.

DMX Mode: This fixture will react with DMX operation. For best

results use only one motor function for each scene (or step), when

programming scenes into a DMX controller. This will give you faster

mirror and faster gobo/color changes. For Example:

A. With DMX controller move the mirror up then program the step.

B. Move the mirror down then program that step.

C. Change the gobo/color wheel then program that step.

D. Continue this pattern to achieve best results.

1. Operating through a DMX controller allows users to create custom

programs tailored to their individual needs. This function also

allows you to use your fixtures as spots.

2. This operation will allow you to control each individual fixtures

traits with a standard DMX 512 controller such as the American DJ

Show Designer™ or the American DJ®DMX Operator.™

3. The DJ Roller™ uses four DMX channels to operate; Channel 1

is Rotation, channel 2 is Tilt, channel 3 is Color change, and

channel 4 Gobo change.

4. To run your fixture in DMX mode, plug in the fixture via the XLR

connections to any standard DMX controller. - Follow the set-up

specifications that come with the controller.

5. Set the proper fixture DMX address. The DMX address is adjusted

with the dipswitches on the bottom panel of the unit. Page 13

Details a DMX chart. Please note that the chart on page 13 is set-

up as a guide only. For proper DMX addressing please refer to the

DMX binary rules on page 6.

DJ Roller™ Operating Instructions DJ Roller™ Operating Instructions

©American DJ Supply®- www.americandj.com - DJ Roller™ Instruction Manual Page 8©American DJ Supply®- www.americandj.com - DJ Roller™ Instruction Manual Page 7

Operating Modes:

You may use the DJ Roller™in three different modes:

• Stand alone mode - The unit will react to sound, chasing through

the several built in programs. You can also use the optional MINI/C

Remote Control to blackout the units.

• Master/Slave mode - You can daisy chain up to 4 units together to

get a synchronized light show that will react to sound chasing

through several built in programs.

• DMX control mode - This function will allow you to control each

individual fixtures traits with a standard DMX 512 controller such as

the American DJ Show Designer.™

For best results use fog or special effects smoke to enhance the

beams projections. The DJ Roller™ comes with a protective transpor-

tation cover. Be sure to remove it before attempting any operation!

Stand Alone Mode:

1. To operate as a stand alone unit, via its internal chases and

microphone, turn all dip switches off (see Page 13; Master/Slave).

2. Adjust the sensitivity knob on the bottom of the unit so the unit

will react to sound.

3. The DJ Roller™ will now react to the bass sound of music via the

internal microphone.

Master-Slave Operation:

1. This function will allow you to link up to 16 units together to run on

the master unit’s internal programs.

2. In Master-Slave operation one unit will act as the controlling unit

and the others will react to the controlling units programs. Any unit

can act as a Master or as a Slave.

3. Daisy chain your units via the XLR connector on the bottom

of the units.

4. Use standard XLR microphone cables to link your units together.

Remember that the Male XLR connector is the input and the

Female XLR connector is the output.

5. The first unit in the chain (master) will use the female XLR connec-

tor only - The last unit in the chain will use the male XLR connector

only.

6. Turn all the master units dip switches to the off position (see

Due to fog residue, smoke, and dust, cleaning the internal and external

optical lenses must be carried out periodically to optimize light output.

1. Use normal glass cleaner and a soft cloth to wipe down the outside

casing.

2. Use a brush to wipe down the fan grill.

3. Clean the external optics with glass cleaner and a soft cloth every

20 days. Situation may very. If used heavily in clubs with lots of

fog, cleaning may be required more often.

4. Clean the internal optics with glass cleaner and a soft cloth every

30-60 days.

5. Always be sure to dry all parts completely before plugging the

unit in.

Cleaning frequency depends on the environment in which the fixture

operates (i.e. smoke, fog residue, dust, dew).

©American DJ Supply®- www.americandj.com - DJ Roller™ Instruction Manual Page 10©American DJ Supply®- www.americandj.com - DJ Roller™ Instruction Manual Page 9

DJ Roller™ Cleaning

DJ Roller™ Lamp & Fuse Replacement

Always replace with the exact same type lamp and fuse, unless

otherwise speciﬁed by an authorized American DJ®service tech-

nician.

Caution: Always disconnect the units main power before performing

any type of service or fuse replacement! Always disconnect the main

power before attempting to replace the lamp.

Lamp Replacement:

1. Be sure to follow proper procedures when handling halogen lamps.

2. Lamp replacement has been made simple by incorporating the use

of a removable lamp tray and thumb screws.

3. Loosen the thumb screw on rear cover.

4. Remove the tray.

5. Remove and replace the bulb.

6. Reassemble.

Fuse Replacement: To replace the protective fuse, use a ﬂat head

screwdriver to unscrew and remove the fuse holder. Gently remove

the old fuse and replace it with a new one. Insert the fuse holder back

into the fuse housing and tighten.

For any other service related issues, please contact American DJ®

customer support.

The DJ Roller™ may be controlled by a wide range of controllers such

as the American DJ®Show Designer,™ or DMX Operator.™ A basic

blackout controller (MINI/C) may also be used with the DJ Roller.™

MINI/C features:

DJ Roller™ Optional Remote

The MINI/C controller may be purchased separately allowing you to

control the main unit, and any others connected to it, while it is in

stand alone mode. You can set the unit to blackout. If you have more

than one unit, make sure the remote control is plugged into the first

unit in the daisy chain. The remote control will not have any effect if

the unit is in DMX mode. When the unit is in blackout mode, the light

will come on next to the blackout button.

30 ft. cable

Stand-By (Blackout)

Listed below are a few common problems the user may encounter,

with solutions.

No light from the unit;

1. Check if the ‘Power On’ (red) LED is lit and the fan is running. If

not, there is no main power supply.

2. Check the fuse in the back panel.

3. Check if lamp is lit. The user should be able to see some light

escape through the fan. If power is present but the lamp is not lit,

lamp may need to be replaced.

Note: The unit has been designed to shut the lamp down after

60 seconds of inactivity. This is a way of extending lamp life, be

assured this is not a problem with the fixture.

Unit not responding to DMX;

1. If the Green LED on the top of the unit is flashing, the unit is

definitely receiving DMX

2. Check the dip switch settings.

3. If the DMX LED is not lit, check that the DMX cables are connected

properly and are wired correctly (pin 3 is ‘hot’; on some other

DMX devices pin 2 may be ‘hot’). Also, check that all cables are

connected to the right connectors; it does matter which way the

inputs and outputs are connected.

4. If it is a bad connection, the Green LED may flash when cables are

wiggled (but remember it may also be the unit sensing audio!)

5. If DMX connectors are fairly short, ordinary microphone cables

may be used. For longer runs, this may cause data transmission

problems (which will show up as random or incorrect movements)

for best result, use proper balanced data transmission cable.

Unit does not respond to sound;

1. Check to see if the unit is receiving DMX (the green LED should

be off).

2. Tapping the microphone should cause the LED to flash (quiet or

high pitched sounds will not activate the unit). If the red LED

does not flash to sound there may be an internal problem.

3. Be sure the audio sensitivity knob is turn in the full clockwise

position (maximum sensitivity).

Unit blacks out in stand alone mode;

1. Some of the units’ built-in patterns include special effects such

as blackout sweeps.

2. Be sure the audio sensitivity knob is turn in the full clockwise

position (maximum sensitivity).

If problems are not resolved; Contact American DJ®customer

support for possible service options.

©American DJ Supply®- www.americandj.com - DJ Roller™ Instruction Manual Page 12©American DJ Supply®- www.americandj.com - DJ Roller™ Instruction Manual Page 11

DJ Roller™ Trouble Shooting DJ Roller™ Trouble Shooting Cont.

The DJ Roller™ carries a one year (365 days) limited warranty. We

recommend you fill out the enclosed warranty card to validate your

purchase. All returned service items whether under warranty or not,

must be freight pre-paid and accompany a return authorization (R.A.)

number. If the unit is under warranty, you must provide a copy of your

proof of purchase invoice. Please contact American DJ®customer

support for a R.A. number.

DJ Roller™ Product Registration

DJ Roller™ Focusing

1. To focus a DJ Roller,™ it is best to first turn down the music

sensitivity knob to its minimum position.

2. Loosen the thumb screw on the front of the unit that hold the lens

in place.

3. Adjust the focus by manually moving the lens up and down.

4. Tighten the thumb screw after you achieve your desired focus.

DJ Roller™ Halogen Lamp Warning

This fixture is fitted with halogen lamps which are highly susceptible to

damage if improperly handled. Never touch lamp with your bare fingers

as the oil from your hands will shorten lamp life. Also, never move the

fixture until the lamps have had ample time to cool. Remember, lamps

are not covered under warranty conditions.

DJ Roller™ DMX Settings

198765432

198765432 198765432

198765432 198765432 198765432 198765432

Head 2

Head 4

Head 3 Head 15Head 11

Head 14Head 10

Head 9 Head 13

Head 7

Head 6

Head 5

Head 16

Head 12

Head 8

Head 1

ON ON

86 954

371 2

86 954

371 2

86 954

371 2 86 954

371 2

86 954

371 2

DJ Roller™ DMX Traits

©American DJ Supply®- www.americandj.com - DJ Roller™ Instruction Manual Page 14

©American DJ Supply®- www.americandj.com - DJ Roller™ Instruction Manual Page 13

DMX CHANNEL

12 34

ROTATION TILT COLOR GOBO

GOBO 7 132-153

GOBO 8 154-175

GOBO 4 66-87

GOBO 1 0-21

GOBO 3 44-65

GOBO 2 22-43

GOBO 5 88-109

GOBO 6 110-131

BLACKOUT 0-28

PURPLE 232-255

PINK 203-231

ORANGE 174-202

YELLOW 145-173

GREEN 116-144

BLUE 87-115

RED 58-86

WHITE 29-67

CW 00˚

45˚255

STOP

128

CCW255

23˚128

GOBO 10 198-219

GOBO 9 176-197

GOBO 11 220-241

SHUTTER 242-255

DJ Roller™ Master/Slave Settings

86 954

371 2

6 954

371 2

6 954

371 2

6 954

371 2

6 954

371 2

Slave 2

Slave 4

Slave 3 Slave 15Slave 11

Slave 14Slave 10

Slave 9 Slave 13

Slave 7

Slave 6

Slave 5

Slave 16

Slave 12

Slave 8

Master - Head 1

ON ON

86 954

371 2

86 954

371 2

86 954

371 2 86 954

371 2

86 954

371 2 86 954

371 2

86 954

371 2 86 954

371 2

86 954

371 2

86 954

371 2

86 954

371 2

The chart below details the Master/Slave dip switch setting for all 16

units. For best operation never use more than 16 units in a Master/

Slave conﬁguration.

This chart details the DMX dip switch setting for the first 16 units. This

chart is designed as a guide only. For dip switch settings beyond the

sixteenth unit or for units not starting at DMX channel one, please

follow standard binary DMX protocol for the correct dip switch settings.

For DMX Operator™ settings, please refer to the DMX Operator™

manual. DJ Roller™ Gobo Layout

This diagrams details the 11

different gobo patterns.

American DJ World Headquarters:

4295 Charter Street Los Angeles, CA 90058 USA

Tel: 323-582-2650 / Fax: 323-582-2610

Web: www.americandj.com / E-mail: [email protected]

DJ Roller™ Specifications

Model: DJ Roller™

Weight: 21 Lbs.

Dimensions: 18” x 8.6” x 4.3”

Lamp: ZB-JCR/H5 15v/150w

500 hour lamp life

Fuse: 5

A/250v GMA

Voltage*: 120v~60Hz or

220v~50Hz

Gobos: 10 plus spot

Colors: 7 Plus White

Cooling: Fan Cooled

Working Position: Any Safe Position

Sound Active: Yes

* Operating voltage is preset at the factory.

Please Note: Speciﬁcations and improvements in the design of

this unit and this manual are subject to change without any prior

written notice.

1-YEAR LIMITED WARRANTY

A. American DJ®hereby warrants, to the original purchaser, American DJ®products to be

free of manufacturing defects in material and workmanship for a period of 1 Year (365 days)

from the date of purchase. This warranty shall be valid only if the product is purchased

within the United States of America, including possessions and territories. It is the owner’s

responsibility to establish the date and place of purchase by acceptable evidence, at the

time service is sought.

B. For warranty service, send the product only to the American DJ®factory. All shipping

charges must be pre-paid. If the requested repairs or service (including parts replacement)

are within the terms of this warranty, American DJ®will pay return shipping charges only

to a designated point within the United States. If the entire instrument is sent, it must be

shipped in its original package. No accessories should be shipped with the product. If any

accessories are shipped with the product, American DJ®shall have no liability whatsoever

for loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product

is modiﬁed in any manner which American DJ®concludes, after inspection, affects the reli-

ability of the product; if the product has been repaired or serviced by anyone other than the

American DJ®factory unless prior written authorization was issued to purchaser by Ameri-

can DJ®; if the product is damaged because not properly maintained as set forth in the

instruction manual.

D. This is not a service contract, and this warranty does not include maintenance, cleaning

or periodic check-up. During the period speciﬁed above, American DJ®will replace defec-

tive parts at its expense, and will absorb all expenses for warranty service and repair labor

by reason of defects in material or workmanship. The sole responsibility of American DJ®

under this warranty shall be limited to the repair of the product, or replacement thereof,

including parts, at the sole discretion of American DJ®. All products covered by this warranty

were manufactured after January 1, 1990, and bear identifying marks to that effect.

E. American DJ®reserves the right to make changes in design and/or improvements upon

its products without any obligation to include these changes in any products theretofore

manufactured.

F. No warranty, whether expressed or implied, is given or made with respect to any acces-

sory supplied with products described above. Except to the extent prohibited by applicable

law, all implied warranties made by American DJ®in connection with this product, including

warranties of merchantability or ﬁtness, are limited in duration to the warranty period set

forth above. And no warranties, whether expressed or implied, including warranties of mer-

chantability or ﬁtness, shall apply to this product after said period has expired. The con-

sumer’s and or Dealer’s sole remedy shall be such repair or replacement as is expressly

provided above; and under no circumstances shall American DJ®be liable for any loss or

damage, direct or consequential, arising out of the use of, or inability to use, this product.

G. This warranty is the only written warranty applicable to American DJ®Products and

supersedes all prior warranties and written descriptions of warranty terms and conditions

heretofore published.

H. Lamps are not covered under this or any other warranty, either written or implied.

DJ Roller™ Warranty

Inhaltsverzeichnis

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ Mega Flash DMX Bedienungsanleitung

American DJ

American DJ Saga Bedienungsanleitung

American DJ

American DJ UV Panel HP Bedienungsanleitung

American DJ

American DJ Flash Tube Buffer Bedienungsanleitung

American DJ

American DJ Mega Bar PRO Bedienungsanleitung

American DJ

American DJ RotoPod 250 Bedienungsanleitung

American DJ

American DJ Fusion Scan 250 Montageanleitung

American DJ

American DJ Galaxian Royale Bedienungsanleitung

American DJ

American DJ GP 250 Bedienungsanleitung

American DJ

American DJ Multi-Saucer Bedienungsanleitung

American DJ

American DJ 2.4 Bedienungsanleitung

American DJ

American DJ Spherion Tri LED Bedienungsanleitung

American DJ

American DJ Rolling Star Bedienungsanleitung

American DJ

American DJ Mega Panel LED Bedienungsanleitung

American DJ

American DJ FLASHBACK 4 Bedienungsanleitung

American DJ

American DJ Confusion Bedienungsanleitung

American DJ

American DJ Mega Panel LED Bedienungsanleitung

American DJ

American DJ Starball II Bedienungsanleitung

American DJ

American DJ Revo Burst Bedienungsanleitung

American DJ

American DJ Roto-Balls VS MKII Bedienungsanleitung

American DJ

American DJ Snow Flurry Bedienungsanleitung

American DJ

American DJ Micro Wash RGBW Bedienungsanleitung

American DJ

American DJ Tempest 250MSD Bedienungsanleitung

American DJ

American DJ Prismatic Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung