American DJ Utopia 250S Bedienungsanleitung

American DJ®

American DJ

4295 Charter Street

Los Angeles CA. 90058

www.americandj.com

Revised 8/01

User Instructions

Unpacking: Thank you for purchasing the Utopia 250S™ by Ameri-

can DJ®. Every Utopia 250S™ has been thoroughly tested and has

been shipped in perfect operating condition. Carefully check the ship-

ping carton for damage that may have occurred during shipping. If the

carton appears to be damaged, carefully inspect your ﬁxture for any

damage and be sure all equipment necessary to operate the unit has

arrived intact. In the event damage has been found or parts are miss-

ing, please contact our toll free customer support number for further

instructions. Do not return this unit to your dealer without ﬁrst contact-

ing customer support.

Introduction: This unit use a single color/gobo wheel combination for

vibrant colors and extravagant gobo patterns. The Utopia 250S™ is an

intelligent fixture that can run In DMX mode, as a stand alone sound

active piece, or in a Master/Slave configuration. The Utopia 250S™

comes with several build in programs and is best used in multiples of

four. This piece is best used with a fog or haze machine to enhance

the beam output. When used in DMX mode channel 4 access a spe-

cial strobe function. When used as a stand alone unit or when used

in multiples linked in a master/slave configuration an optional Utopia/C

controller may be used. The optional controller will access different pro-

grams and control a blackout function.

Customer Support: American DJ®provides a toll free customer sup-

port line, to provide set up help and to answer any question should you

encounter problems during your set up or initial operation. You may

also visit us on the web at www.americandj.com for any comments or

suggestions. Service Hours are Monday through Friday 9:00 a.m. to

5:00 p.m. Paciﬁc Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2610

E-mail: [email protected]

Warning! To prevent or reduce the risk of electrical shock or ﬁre, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

your nearest American DJ®dealer.

Utopia 250S™ General Information

©American DJ®- www.americandj.com - Utopia 250S™ Instruction Manual Page 2

©American DJ®- www.americandj.com - Utopia 250S™ Instruction Manual Page 3

Utopia 250S™ Halogen Lamp Warning

This fixture is fitted with halogen lamps which are

highly susceptible to damage if improperly handled.

Never touch the lamps with your bare fingers as

the oil from your hands will shorten lamp life. Also,

never move the fixture until the lamps have had

ample time to cool. Remember, lamps are not cov-

ered under warranty conditions.

• Micro-Stepping Motors for Smooth Color and Gobo Transitions

• DMX-512 Protocol Compatible (Uses Four DMX Channels)

• Full Manual Focusing

• Fan Cooled.

• 17 Color/Gobo Combinations Plus Spot.

• Master/Slave Operation

• Internal Microphone with Volume Sensitivity Knob

• Easy Lamp Replacement

• ZB-ELC 24v/250w Lamp

• Variable Speed Strobe Function

• Optional Utopia/C Remote Controller

Utopia 250S™ Features

The Utopia 250S™ carries a one year (365 days) limited warranty.

Please fill out the enclosed warranty card to validate your purchase.

All returned service items whether under warranty or not, must be

freight pre-paid and accompany a return authorization (R.A.) number.

If the unit is under warranty, you must provide a copy of your proof

of purchase invoice. Please contact American DJ®customer support

for a R.A. number.

Utopia 250S™ Product Registration

• To reduce the risk of electrical shock or ﬁre, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required voltage

for your unit.

• Do not attempt to operate this unit if the power cord has been frayed

or broken.

• Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and ﬁre in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product outdoors

voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 7 for cleaning details.

• Heat -The appliance should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances (includ-

ing amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the appliance.

C. The appliance has been exposed to rain or water.

D. The appliance does not appear to operate normally or exhibits a

marked change in performance.

Utopia 250S™ Safety Precautions

©American DJ®- www.americandj.com - Utopia 250S™ Instruction Manual Page 4

To optimize the performance of this product, please read these operat-

ing instructions carefully to familiarize yourself with the basic operations

of this unit. These instructions contain important safety information

regarding the use and maintenance of this unit. Please keep this

manual with the unit, for future reference.

Utopia 250S™ General Instructions

©American DJ®- www.americandj.com - Utopia 250S™ Instruction Manual Page 6©American DJ®- www.americandj.com - Utopia 250S™ Instruction Manual Page 5

Utopia 250S™ Controls and Functions

REAR

FRONT

1 2 3 4

1 2 3 4 5 6 7 8 9

1. Thumb Screw - This thumb screw holds the lamp socket assembly

cover (16) into place.

2. Microphone - This microphone receives external low frequencies

to trigger the unit in Sound-Active and Master/Slave mode.

3. Audio Sensitivity Knob - This adjust audio sensitivity of the

internal microphone (3). Turning the sensitivity knob in the clockwise

direction will increase the sensitivity to sound. Turning the knob in

the counter clockwise direction will decrease the ﬁxture’s sensitivity

to sound.

4. Option Switches - These switches will activate one of four

options:

Switch 1: Focus - When activated this switch will center the mirror

with a white spot. This will allow you to focus the beam

properly.

Switch 2: Sound Active - Turning this switch to the on position will

activate sound-active mode.

Switch 3: Inverted Pan - When activated this switch will invert the

PAN value. Left will become right and vice versa.

Switch 4: Inverted Tilt - When activated this switch will invert the

TILT value. Up will become down and vice versa.

5. Dip Switches - These switches serve two functions. In master

slave mode these switches are used to assign a speciﬁc head

address. In DMX mode these switches are used to assign a DMX

address to the unit. In DMX mode each switch corresponds to a

speciﬁc value based on binary code. See page 7 for a detailed

explanation of DMX binary code.

6. Power Indicator - This light will ﬂash when the unit is in use.

7. Utopia/C Controller Jack - This jack is for use with the optional

Utopia/C Blackout controller only. Do not attempt to connect an audio

signal this jack, this will damage the PC board and void your manufac-

tures warranty!

8. XLR Input Jack - This jack is used to accept an incoming DMX

signal or Master/Slave signal.

9. XLR Output Jack - This jack is used to transmit the incoming

Utopia 250S™ Controls and Functions

Universal DMX Control: This function allows you to use a universal

DMX 512 controller as the American DJ®DMX Operator™ or Show

Designer.™ to control mirror movement and the color/gobo wheel. The

use of a DMX controller will allow you to customize the use of fixtures

allowing you to control the rotation direction as well as the rotation

speed. Operating through a DMX controller allows the freedom to

create unique programs tailored to one’s individual needs.

1. The Utopia 250S™ uses four DMX channels. Channel 1 controls

pan, channel 2 controls tilt, channel 3 controls the color/gobo

wheel, and channel 4 controls the strobe function. See page 14 for

detailed description of the DMX traits.

2. To control your fixture in DMX mode, follow the set-up procedures

Utopia 250S™ Operation

©American DJ®- www.americandj.com - Utopia 250S™ Instruction Manual Page 8©American DJ®- www.americandj.com - Utopia 250S™ Instruction Manual Page 7

DMX signal to another DMX ﬁxture, or transmit a Master/Slave signal

to the nest Utopia 250S™ in the chain. For best results in DMX or

Master/Slave mode terminate this jack if it is the last unit in the

chain. See “Terminator” on page 7.

10. Fuse Holder - This housing stores the 3 amp GMA protective

fuse. Always replace with the exact same type fuse, unless other

wise instructed, by an authorized American DJ®service technician.

11. Power Cord - Connect only to a matching power outlet. Never use

this ﬁxture is the ground prong has been removed or broken off.

12. Mirror - This is a highly reﬂective surface mirror speciﬁcally

designed to optimize and enhance beam output. Never use glass

cleaner that contain ammonia to clean the surface of the mirror (such

as Windex).

13. Lens - This is a fully focusing high quality lens. Focus the lens by

manually turning the lens in a clockwise or counter-clockwise direc-

tion.

14. Lamp Socket Assembly - This assembly holds a ZB-ELC

(24v/250w) lamp. A long life version of lamp may be used in place of

the original lamp (ZB-ELC3 300 hours).

15. Lamp Socket Assembly Plate - This plate accesses the lamp

socket assembly.

Utopia 250S™ Controls and Functions Utopia 250S™ Operation

on pages 5 - 7 as well as the set-up specifications that are included

with your DMX controller.

3. Use the controller’s faders to control the various DMX fixture traits.

4. This will allow you to create your own programs.

5. When using a DMX controller and setting up for DMX operation

follow the dip switch settings on page 14.

6. For help operating in DMX operation consult the manual included

with your DMX controller.

7. For longer cable runs (more than a 100 feet) use a terminator on

the last fixture.

Stand-Alone Operation (Sound Active): This function allows a

single unit to run to the beat of the music. Only use this function when

running a single unit, or when running several units as individuals.

1. To activate the Sound-Active mode be sure the number 2 function

switch is set to the “ON” position and refer to “Master Unit” on the

Master-Slave DIP SWITCH chart on page 14).

2. The unit will now react to the low frequencies of music via the inter-

nal microphone.

3. Adjust the audio sensitivity knob on the top of the unit to make the

unit more or less sensitive to sound. Turning the sensitivity knob in

the clockwise direction will increase the sensitivity, turning the knob

in the counter-clockwise direction will decrease the ﬁxture’s sensi-

tivity to sound.

4. The optional Utopia/C Blackout Controller may be used with this

function for blackout.

Master-Slave Operation (Sound Active): This function will allow

you to link up to 4 units together and operate without a controller. The

units will be sound activated. In Master-Slave operation one unit will act

as the controlling unit and the others will react to the controlling units

programs. Any unit can act as a Master or as a Slave.

1. Using standard XLR microphone cables, daisy chain your units

together via the XLR connector on the rear of the units. Remember

the Male XLR connector is the input and the Female XLR connector

is the output. The ﬁrst unit in the chain (master) will use the female

XLR connector only - The last unit in the chain will use the male

XLR connector only. For longer cable runs we suggest a terminator

at the last fixture.

©American DJ®- www.americandj.com - Utopia 250S™ Instruction Manual Page 10©American DJ®- www.americandj.com - Utopia 250S™ Instruction Manual Page 9

Utopia 250S™ Operation

2. Follow the chart on page 14 for proper unit dip switch settings.

3. The optional Utopia/C Blackout Mini-Controller may be used with

this function for blackout.

4. After all the units settings have been set and are plugged in, adjust

the sensitivity knob on the rear of the master unit to make them

react to sound.

Note: In Stand-Alone and Master-Slave operation the units will blackout

to conserve bulb life when a sound source is not received.

Power Supply: Before plugging your unit in, be sure the source volt-

age in your area matches the required voltage for your American DJ®

Utopia 250S.™ The American DJ®Utopia 250S™is available in a 120v

and 220v version. Because line voltage may vary from venue to venue,

you should be sure your unit voltages matches the wall outlet voltage

before attempting to operate you ﬁxture.

DMX-512: DMX is short for Digital Multiplex. This is a universal

protocol used as a form of communication between intelligent fixtures

and controllers. A DMX controller sends DMX data instructions from

the controller to the fixture. DMX data is sent as serial data that

travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR

terminals located on all DMX fixtures (most controllers only have a

DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of

different manufactures to be linked together and operate from a single

controller, as long as all ﬁxtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX

fixtures try to use the shortest cable path possible. The order in which

fixtures are connected in a DMX line does not influence the DMX

addressing. For example; a fixture assigned a DMX address of 1 may

be placed anywhere in a DMX line, at the beginning, at the end, or

anywhere in the middle. When a fixture is assigned a DMX address of

1, the DMX controller knows to send DATA assigned to address 1 to

that unit, no matter where it is located in the DMX chain.

Dip-switches in DMX mode: This unit uses dip switches to assign a

DMX address. Each dip switch represents a binary value.

Utopia 250S™ Set Up

Dip Switch 1 address equals 1

Dip Switch 2 address equals 2

Dip Switch 3 address equals 4

Dip Switch 4 address equals 8

Dip Switch 5 address equals 16

Dip Switch 6 address equals 32

Dip Switch 7 address equals 64

Dip Switch 8 address equals 128

Dip Switch 9 address equals 256

Dip Switch 10 - Some unit omit dip switch 10, when a unit does

included dip switch 10 it is used for special functions such as sound

activation.

Each dip switch has a preset value. A specific DMX address is set by

combining the dip switches that sum your desired value. For example:

To achieve a DMX address of 21, combine dip switches 1, 3, and 5.

Sense dip switch 1 has a value of 1, dip switch 3 has a value of 4,

and dip switch 5 has a value of 16, the combination of the create a

DMX value of 21.

Set DMX address 21: Set DMX address 201:

Dip-switches # 1 = 1 Dip-switches # 1 = 1

3= 4 4 = 8

5= 16 7 = 64

= 21 8 = 128

= 201

Data Cable (DMX Cable) Requirements (For DMX and Master/

Slave Operation): The Utopia 250S™ can be controlled via DMX-512

protocol. The American DJ®Utopia 250S™ is a four channel DMX unit.

The DMX address is set on the front panel of the Utopia 250S™. Your

unit and your DMX controller require a standard

3-pin XLR connector for data input and data output

(Figure 1). If you are making your own cables, be

sure to use standard two conductor shielded cable

(This cable may be purchased at almost all pro

sound and lighting stores). Your cables should be

made with a male and female XLR connector on

either end of the cable. Also remember that DMX

cable must be daisy chained and can not be split.

Utopia 250S™ Set Up

ON 198765432 10

1282832

256651641

DMX CHANNEL

Figure 1

Utopia 250S™ Fuse & Lamp Replacement

©American DJ®- www.americandj.com - Utopia 250S™ Instruction Manual Page 11 ©American DJ®- www.americandj.com - Utopia 250S™ Instruction Manual Page 12

Caution: Always replace with the exact same type lamp and fuse,

unless otherwise specified by an authorized American DJ®technician.

Replace with anything other than the specified part can damage your

unit and will void your manufactures warranty.

Warning: If, after replacing the lamp or fuse either one continues

to blow, STOP using the unit. Contact customer support for further

instructions, you may have to return the unit for servicing. Continuing

to use the unit may cause serious damage.

Fuse Replacement: Disconnect the unit’s main power supply. Insert

a standard flat head screw driver in to the fuse holder housing. Turn

the screwdriver in counter-clockwise direction to remove the fuse

holder. Remove the fuse holder to expose the fuse. Remove the old

fuse and discard it. Replace the fuse with the same type. Insert the

fuse holder back into it’s housing and turn it in clockwise direction to

lock the holder in place.

Lamp Replacement: Caution! Never attempt to change the lamp

while the fixture is plugged in. Always disconnect the main power and

allow the unit ample time to cool before attempting to replace the

lamp. Lamp replacement has been made simple by incorporating the

use of a flip-up front cover that is retained by thumb screws.

1. Be sure to follow the proper handling procedures that deal

with halogen lamps.

2. Remove the thumb screw on the top/rear of the unit that holds the

lamp socket assembly cover in place.

3. After removing the thumb screw, slide out the cove from the rear of

the unit to expose the lamp socket assembly.

4. Carefully remove the old lamp and discard it in the trash.

5. Replace the lamp with an exact match and reassemble in reverse

order.

Notice: Be sure to follow ﬁgures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

Utopia 250S™ Set Up

DMX512 IN

3-PIN XLR

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Conﬁguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number ZDMX/T) will decrease the possibilities of erratic

behavior.

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture. Figure 4

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin XLR

connectors for DATA transmission in place of 3-pin. 5-pin XLR ﬁxtures

may be implemented in a 3-pin XLR DMX line. When inserting standard

5-pin XLR connectors in to a 3-pin line a cable adaptor must be used,

these adaptors are readily available at most electric stores. The chart

below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Thumb Screws

Lamp Cover

Lamp Socket

Assembly

©American DJ®- www.americandj.com - Utopia 250S™ Instruction Manual Page 14

Utopia 250S™ Cleaning

Utopia 250S™ Trouble Shooting

Fixture Cleaning: Due to fog residue, smoke, and dust cleaning the

internal and external optical lenses and mirror should be carried out

periodically to optimize light output. Cleaning frequency depends on

the environment in which the fixture operates (I.e. smoke, fog residue,

dust, dew). In heavy club use we recommend cleaning on a monthly

basis. Periodic cleaning will ensure longevity, and crisp output.

1. Use normal glass cleaner and a soft cloth to wipe down the outside

casing.

2. Use a brush to wipe down the cooling vents and fan grill.

3. Clean the external optics and mirror with glass cleaner and a soft

cloth every 20 days.

4. Clean the internal optics with glass cleaner and a soft cloth every

30-60 days.

5. Always be sure to dry all parts completely before plugging the unit

back in.

Trouble Shooting: Listed below are a few common problems that you

may encounter, with solutions.

No light output from the unit;

1. Be sure you have connected your unit into a standard 120V wall

outlet.

2. Be sure the external fuse has not blown. The fuse is located on the

bottom panel of the unit.

3. Remove the lamp cover and be sure the lamp is seated in its

socket properly. Occasionally lamps become loose during shipping

be sure the lamp is push in to its socket all the way.

4. Be sure the fuse holder is completely and properly seated.

Unit does not respond to sound;

1. Low frequencies (bass) should cause the unit to react to sound.

Tapping on the microphone, quiet or high pitched sounds may not

activate the unit.

2. Be sure the SENSITIVITY KNOB (5) is not set to the minimum

position

©American DJ®- www.americandj.com - Utopia 250S™ Instruction Manual Page 13

Utopia 250S™ Master/Slave Settings

Utopia 250S™ DMX Traits

This chart details the Master/Slave dip switch setting for Master/Slave

configuration. Use this configuration only when you will be using your

fixtures in a Master/Slave configuration. Be sure the number 2 function

switch is set to the on position for sound-active operation.

This chart below details the DMX traits. The individual trait can only be

accessed an universal DMX controller.

198765432

Master - Head 1

198765432

Head 2

198765432

Head 3

198765432

Head 4

This chart details the gobo pattern as well as

the gobo wheel placement. When used with

a DMX controller gobo one may be used as

a spot or color changer. Gobos two through

eight will rotate, rotation will be controlled by

DMX channel five. Gobos two through eight

may also be replaced with custom gobos.

Please contact customer service for custom

gobos.

DMX CHANNEL

12 34

PAN TILT COLOR/GOBO STROBE

Lamp Off 00

White/Lg Spot 248-255

Strobe 8fps 247

Strobe 2fps 208

Fast Rotation 207

Gobo 2/Yellow 32-39

Gobo 1/Red 24-31

Blackout 16-23

Lrg Spot/White 08-15

0˚ 00˚

90˚255

73˚128

145˚255

45˚128

Blackout 01-07

Gobo 3/Green 40-47

Gobo 4/Lt Blue 48-55

Gobo 5/Blue 56-63

Gobo 6/Purple 64-71

Gobo 7/Red-Green 72-79

Gobo 8/Purple-Wht 80-87

Gobo 9/4-Colors 88-95

Gobo 10/White 96-103

Gobo 11/Red 104-111

Gobo 12/Yellow 112-119

Gobo 13/Green 120-127

Gobo 14/Lt Blue 128-135

Gobo 15/Blue 136-143

Gobo 16/Purple 144-151

Gobo 17/Ylw-Lt Blue 152-159

Slow Rotation 160

Strobe 7fps 129

Strobe 1fps 01

Stop 00

Strobe 1fps 255

Strobe 7fps 128

Strobe Step Up

Strobe Step Down

1432

Function Switch

©American DJ®- www.americandj.com - Utopia 250S™ Instruction Manual Page 15

X = OFF

O =ON

#1 #2 #3 #4 #5

36496128160192224 256 288320352 384 416 448 480

1336597129161193225 257 289321353 385 417 449 481

2346698130 162 194 226 258 290 322 354 386 418 450 482

3356799131163195227 259 291323355 387 419 451 483

43668100132 164 196 228 260 292 324 356 388 420 452 484

53769101 133 165 197 229 261 293 325 357 389 421 453 485

63870102134 166 198 230 262 294 326 358 390 422 454 486

73971103135 167 199 231 263 295 327 359 391 423 455 487

84072104 136 168 200 232 264 296 328 360 392 424 456 488

94173105137 169 201 233 265 297 329 361 393 425 457 489

10 42 74 106 138 170 202 234 266 298 330 362 394 426 458 490

11 43 7 5 107 139 171 203 235 267 299 331 363 395 427 459 491

12 44 76 108 140 172 204 236 268 300 332 364 396 428 460 492

13 45 77 109 141 173 205 237 269 301 333 365 397 429 461 493

14 46 78 110 142 174 206 238 270 302 334 366 398 430 462 494

15 47 79 111 143 175 207 239 271 303 335 367 399 431 463 495

16 48 80 112 144 176 208 240 272 304 336 368 400 432 464 496

17 49 81 113 145 177 209 241 273 305 337 369 401 433 465 497

18 50 82 114 146 178 210 242 274 306 338 370 402 434 466 498

19 51 83 115 147 179 211 243 275 307 339 371 403 435 467 499

20 52 84 116 148 180 212 244 276 308 340 372 404 436 468 500

21 53 85 117 149 181 213 245 277 309 341 373 405 437 469 501

22 54 86 118 150 182 214 246 278 310 342 374 406 438 470 502

23 55 87 119 151 183 215 247 279 311 343 375 407 439 471 503

24 56 88 120 152 184 216 248 280 312 344 376 408 440 472 504

25 57 89 121 153 185 217 249 281 313 345 377 409 441 473 505

26 58 90 122 154 186 218 250 282 314 346 378 410 442 474 506

27 59 91 123 155 187 219 251 283 315 347 379 411 443 475 507

28 60 92 124 156 188 220 252 284 316 348 380 412 444 476 508

29 61 93 125 157 189 221 253 285 317 349 381 413 445 477 509

30 62 94 126 158 190 222 254 286 318 350 382 414 446 478 510

31 63 95 127 159 191 223 255 287 319 351 383 415 447 479 511

DMX DIP Switch Settings

DIP SWITCHES

OOOOOXOOOXXXXXXX

OOOOOOOOXXXXXX XX

OXOXOOXXOOXX XXOO

XOXXOOOXOXXOXOXO

OXXXX

XOXOX

OXXOX

XXXOX

OOOX X

XOOX X

XXOXX

OOXXX

XOXXX

OX OX X

XOOOX

OOXXO

XOXXO

OXXXO

XXXXO

OOOOX

OX OOX

XXOOX

OOX OX

XXXOO

OOOOO

XOOOO

OX OOO

XXOOO

OOX OO

XOXOO

OXXOO

OOOX O

XOOX O

OX OX O

XXOXO

XXXXX

DMX Address

DMX Address Quick Reference Chart

Dip Switch Position

The center numbers of this chart (1-511) represent a DMX address. The "X"'s

and "O"'s along the top and side of the chart represent dip switch poistion ("X"

for off and "O" for on). Find your desired DMX address from the center chart.

Identify the position for dip switches 1-5 from the chart on the left and dip

switches 6-9 from the chart on the top. Adjust the dip switches on your fixture to

match the position settings of the chart. For fixtures with 10 dip switches; dip

switch 10 is reserved for special functions.

This chart list the DMX dip switch setting for DMX address 1 through

511. Follow the instructions below to configure fixture dip switches with

your desired DMX address.

Utopia 250S™ DMX Dip Switch Chart

A Division of the American DJ® Group of Companies

4295 Charter Street Los Angeles, CA 90058 USA

Tel: 323-582-2650 Fax: 323-582-2610

Web: www.americandj.com E-mail: [email protected]

Technical Specifications:

Model: Utopia 250S™

Lamps: ZB-ELC, 24v/250w

Voltage: 120v/60Hz or 220v/50Hz

Dimensions: 20”(H) x 8.5”(W) x 9.25”(D)

with yoke collapsed

Colors Multiple

Gobos: 17, plus spot

Weight: 25 Lbs.

Fuse: 5A GMA (120v)/3A GMA (220V)

Duty Cycle: 30 min on / 5 min off

DMX: 4 Channels

Sound Active: Yes

Working Position: Any Safe, Secure Position

Warranty: 1 Year (365 days)

Please Note: Speciﬁcations and improvements in the design

of this unit and this manual are subject to change without any

prior written notice.

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ DJ Scan/RG Bedienungsanleitung

American DJ

American DJ Charisma II Bedienungsanleitung

American DJ

American DJ Spherion WH LED Bedienungsanleitung

American DJ

American DJ 4-Play Bedienungsanleitung

American DJ

American DJ Ruby Royal Bedienungsanleitung

American DJ

American DJ LED Trispot Bedienungsanleitung

American DJ

American DJ X-Scan LED Plus Bedienungsanleitung

American DJ

American DJ Trance Wheel 250 Bedienungsanleitung

American DJ

American DJ Crystal Bedienungsanleitung

American DJ

American DJ Atmospheric RG LED Bedienungsanleitung

American DJ

American DJ Emerald Scan Bedienungsanleitung

American DJ

American DJ DJ Spot 250 Bedienungsanleitung

American DJ

American DJ Dual Gem Pulse Bedienungsanleitung

American DJ

American DJ Mega Bar LED Bedienungsanleitung

American DJ

American DJ Penta Beam Bedienungsanleitung

American DJ

American DJ Inno Color Beam 12 Bedienungsanleitung

American DJ

American DJ Sunray LED Bedienungsanleitung

American DJ

American DJ Revo Sweep Bedienungsanleitung

American DJ

American DJ Concept Color Bedienungsanleitung

American DJ

American DJ Mega 24PRO Bedienungsanleitung

American DJ

American DJ Reflex Bedienungsanleitung

American DJ

American DJ Chameleon Bedienungsanleitung

American DJ

American DJ Galaxian Move Bedienungsanleitung

American DJ

American DJ Double Twist Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung