American DJ Fire Bowl Bedienungsanleitung

American DJ®

American DJ

4295 Charter Street

Los Angeles Ca. 90058

www.americandj.com

Unpacking: Thank you for purchasing the Fire Bowl™ by American

DJ®. Every Fire Bowl™ has been thoroughly tested and has been

shipped in perfect operating condition. Carefully check the shipping

carton for damage that may have occurred during shipping. If the carton

appears to be damaged, carefully inspect your xture for any damage

and be sure all equipment necessary to operate the system has arrived

intact. In the case damage has been found or parts are missing, please

contact our toll free customer support number for further instructions.

Introduction: The Fire Bowl™ is ready to be hung or set on a

flat surface. The Fire Bowl™ produces a unique flame effect. The

simulated flame effect is further enhanced by the case design that

is designed to look like an ancient torch bowl. This unit may be

hung anywhere by the included hanging hardware, without the

typical danger of an open flame.

Customer Support: American DJ® provides a toll free customer sup-

port line, to provide set up help and to answer any question should

you encounter problems during your set up or initial operation. You may

also visit us on the web at www.americandj.com for any comments or

suggestions. Service Hours are Monday through Friday 9:00 a.m. to

5:00 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2610

E-mail: [email protected]

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

your nearest American DJ® dealer.

Safety Issues: This unit may blow a fuse if the maximum allotted load

of 3 amps is reached. If the fuse needs replacement, always replace

the fuse with same exact type that was remove, unless otherwise

instructed by an authorized American DJ® service technician. Use of a

different type fuse from that which is recommended may cause fire or

electric shock and will void the manufactures warranty.

Fire Bowl™ Introduction

©American DJ Supply® - www.americandj.com - Fire Bowl™ Instruction Manual Page 2

Revised 5/01

User Instructions

• Be sure that the local power outlet match that of the required voltage

for your unit.

• Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short.

• Do not remove the fan cover under any conditions. There are no

user serviceable parts inside.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture.

• This unit is intended for indoor use only, use of this product outdoors

voids all warranties.

• During long periods of non use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-Cord Protection - Power-supply cords should be routed

so that they are not likely to be walked on or pinched by items

placed upon or against them, paying particular attention to cords at

plugs, convenience receptacles, and the point where they exit from

the fixture.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer.

• The fixture should be serviced by qualified service personnel when:

A. The power cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the appliance.

C. The appliance has been exposed to rain or water.

D. The fixture does not appear to operate normally or exhibits a

marked change in performance.

Fire Bowl™ Safety Precautions

Unit Preparation:

Before beginning initial setup of your Fire Bowl,™ make sure there is

no evident damage caused during transportation. In the event that the

unit’s housing or cable is damaged, do not plug the unit in and do not

attempt to use. Please contact customer support for assistance.

1. Remove all packing materials from the Fire Bowl.™

2. Place the Fire Bowl™ on a at level surface or suspend the unit

from the ceiling using the included hanging hardware.

3. Plug the power cord into a grounded electrical outlet with a match-

ing power supply.

4. Locate the power switch on the top inner cover of the unit. To turn

the unit on, ip the switch to the “I” position.

Lamps:

The positioning of the lamps is pre-set and does not require any type of

adjustment. Improperly positioned lamps will create deep spots of color

in the ame. Should the lamps need adjustment due shifting during

transit or after the replacement of a lamp, the lamps may be angled

slightly to overcome any heavy color wash. Should the lamps position-

ing become incorrectly, adjust them as follows:

1. To properly position the lamp the unit must be on. Use an insulated

screwdriver to make any adjustment to the lamps position.

2. The amber lamps should be angled to focused on the lower half of

the silk drape.

3. Position the blue lamp to shine directly in the center of silk drape.

4. All lamps will eventually fade or fail. Replacements lamps are

available from your dealer.

Silk Flame:

Your silk ame has been specially designed and hand cut from ne silk

to interact with the airow and lights to create the illusion of a ame.

Each silk drape is applied prior to shipment and should be in the correct

position. The silk drape has a life of approximately one month when

used continuously in a clean environment. Additional silk drapes may be

purchased through your dealer (part number Z-FLAMEBOWL/SILK).

Fire Bowl™ Set-Up/Operation

©American DJ Supply® - www.americandj.com - Fire Bowl™ Instruction Manual Page 4©American DJ Supply® - www.americandj.com - Fire Bowl™ Instruction Manual Page 3

Fire Bowl™ Halogen Lamp Warning

This fixture is fitted with halogen lamps which are highly susceptible

to damage if improperly handled. Never touch the lamps with your

bare fingers as the oil from your hands will shorten lamp life. Also,

never move the fixture until the lamps have had ample time to cool.

Remember, lamps are not covered under warranty conditions.

Fire Bowl™ Set-Up/Operation Cont.

Repositioning The Flame (Silk Drape):

You may wish to reposition the ame drape to customize the effect.

1. Move the ame drape along the ame attachment rail by sliding

the magnetic ends along the rail.

2. For best results, do not stretch out the ends of the silk drape as

tight as it can get along the bottom. For a more realistic effect

allow some play between the two ends of the silk drape, move the

magnets slightly away from the side of the casing to achieve a

more realistic ame effect.

3. For best results; experiment with the ame position. Slight changes

in the position of the silk drape can drastically change the effect.

©American DJ Supply® - www.americandj.com - Fire Bowl™ Instruction Manual Page 6

©American DJ Supply® - www.americandj.com - Fire Bowl™ Instruction Manual Page 5

Fire Bowl™ Silk Drape

If the silk drape becomes creased, you may iron the ame using a non-

drip iron on a low setting. Do not steam iron.

If the silk drape becomes frayed, you may use a sharp pair of scissors

to carefully cut the loose silk strands. The silk drapes may become

frayed after a period of four weeks.

Fire Bowl™ Warranty Registration

The Fire Bowl™ carries a 90 day limited warranty. Please fill out the

enclosed warranty card to validate your purchase. All returned service

items whether under warranty or not, must be freight pre-paid and

accompany a return authorization (R.A.) number. If the unit is under

warranty you must provide a copy of your proof of purchase invoice.

Please contact American DJ® customer support for a R.A. number.

Fire Bowl™ Cleaning

Fixture Cleaning:

Due to fog residue, smoke, and dust cleaning should be carried out

periodically to optimize light output. Cleaning frequency depends on

the environment in which the fixture operates (I.e. smoke, fog residue,

dust, dew). In heavy club use we recommend cleaning on a monthly

basis. Periodic cleaning will ensure longevity, and crisp output. Always

be sure the unit is turned off and unplugged before performing any

cleaning procedures.

1. Use normal glass cleaner and a soft cloth to wipe down the outside

casing.

2. Use a brush to wipe down the fan grill.

3. Whip down the colored bulb covers with a damp cloth to remove

residue.

4. Always be sure to dry all parts completely before plugging the unit

back in.

Fire Bowl™ Lamp & Fuse Replacement

Caution: Always replace with the exact same type lamp and fuse,

unless otherwise specified by an authorized American DJ® technician.

Replace with anything other than the specified part can damage your

unit and will void your manufactures warranty.

Warning: If after you have replaced the lamp or fuse and you

continue to blow either one, STOP using the unit. Contact customer

support for further instructions, you may have to return the unit for

servicing. Continuing to use the unit may cause serious damage.

Fuse Replacement: Disconnect the unit’s main power supply. Insert

a standard flat head screw driver in to the fuse holder housing located

on inner plate of the unit. Turn the screwdriver in counter-clockwise

direction to unlock the fuse holder. Remove the fuse holder to expose

the fuse. Remove the old fuse and discard it. Replace the fuse with

the same type. Insert the fuse holder back into it’s housing and turn it

in clockwise direction to lock the holder back in to place.

Lamp Replacement: Caution! Never attempt to change the lamps

while the fixture is plugged in. Always disconnect the main power

and allow the unit ample time to cool before attempting to replace

the lamp.

1. Be sure to follow the proper procedures when handling halogen

lamps. Never touch the new lamp with your bare fingers.

2. Carefully pull the lamp out of the socket and discard it.

3. Replace the lamp with an exact match.

4. If necessary adjust the position of the lamps.

©American DJ Supply

American DJ Supply Group of Companies World Headquarters:

4295 Charter Street Los Angeles, CA 90058 USA

Tel: 323-582-2650 Fax: 323-582-2610

Web: www.americandj.com E-mail: [email protected]

Technical Specifications:

Model: Fire Bowl

Lamps: 2x ZB-MR11/O 12v/20w

1 x ZB-MR11/B 12v/20w

Voltage: 120v/60Hz

Dimensions: 5.5”(H) x 14”(W) x 14”(D)

Colors Orange/Blue

Weight: 8 Lbs.

Fuse: 3 Amp GMA

Duty Cycle: None

Working Position: Any Safe, Secure Position

Warranty: 90 Days

©American DJ Supply® - www.americandj.com - Fire Bowl™ Instruction Manual Page 7

90 DAY LIMITED WARRANTY

A. American DJ® hereby warrants, to the original purchaser, American DJ® products to be

free of manufacturing defects in material and workmanship for a period of 90 days from the

date of purchase. This warranty shall be valid only if the product is purchased within the

United States of America, including possessions and territories. It is the owner’s responsibil-

ity to establish the date and place of purchase by acceptable evidence, at the time service

is sought.

B. For warranty service, send the product only to the American DJ® factory. All shipping

charges must be pre-paid. If the requested repairs or service (including parts replacement)

are within the terms of this warranty, American DJ® will pay return shipping charges only

to a designated point within the United States. If the entire instrument is sent, it must be

shipped in its original package. No accessories should be shipped with the product. If any

accessories are shipped with the product, American DJ® shall have no liability whatsoever

for loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product

is modied in any manner which American DJ® concludes, after inspection, affects the reli-

ability of the product; if the product has been repaired or serviced by anyone other than the

American DJ® factory unless prior written authorization was issued to purchaser by Ameri-

can DJ®; if the product is damaged because not properly maintained as set forth in the

instruction manual.

D. This is not a service contract, and this warranty does not include maintenance, cleaning

or periodic check-up. During the period specied above, American DJ® will replace defective

parts at its expense, and will absorb all expenses for warranty service and repair labor by

reason of defects in material or workmanship. The sole responsibility of American DJ® under

this warranty shall be limited to the repair of the product, or replacement thereof, including

parts, at the sole discretion of American DJ®. All products covered by this warranty were

manufactured after January 1, 1990, and bear identifying marks to that effect.

E. American DJ® reserves the right to make changes in design and/or improvements upon

its products without any obligation to include these changes in any products theretofore

manufactured.

F. No warranty, whether expressed or implied, is given or made with respect to any acces-

sory supplied with products described above. Except to the extent prohibited by applicable

law, all implied warranties made by American DJ® in connection with this product, including

warranties of merchantability or tness, are limited in duration to the warranty period set

forth above. And no warranties, whether expressed or implied, including warranties of mer-

chantability or tness, shall apply to this product after said period has expired. The con-

sumer’s and or Dealer’s sole remedy shall be such repair or replacement as is expressly

provided above; and under no circumstances shall American DJ® be liable for any loss or

damage, direct or consequential, arising out of the use of, or inability to use, this product.

G. This warranty is the only written warranty applicable to American DJ® Products and

supersedes all prior warranties and written descriptions of warranty terms and conditions

heretofore published.

H. Lamps are not covered under this or any other warranty either written or implied.

Fire Bowl™ Warranty

Please Note: Specications and improvements in the design

of this unit and this manual are subject to change without any

prior written notice.

Inhaltsverzeichnis

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ Deco 250 Bedienungsanleitung

American DJ

American DJ Snap Shit DMX/D Bedienungsanleitung

American DJ

American DJ Trance Wheel Bedienungsanleitung

American DJ

American DJ S-1500/DMX Bedienungsanleitung

American DJ

American DJ HMI 575TM Bedienungsanleitung

American DJ

American DJ BPP-20 Bedienungsanleitung

American DJ

American DJ Fusion Tri FX Bar Bedienungsanleitung

American DJ

American DJ DJ Spot LED Betriebsanleitung

American DJ

American DJ Color Gem Bedienungsanleitung

American DJ

American DJ MACE II Bedienungsanleitung

American DJ

American DJ Trance Wheel 250 Bedienungsanleitung

American DJ

American DJ Fusion FX Bar 4 Bedienungsanleitung

American DJ

American DJ Festive Light Pak II Bedienungsanleitung

American DJ

American DJ Theatrix PRO 48 LED Bedienungsanleitung

American DJ

American DJ AVIATOR-SP8 Bedienungsanleitung

American DJ

American DJ Warp! Bedienungsanleitung

American DJ

American DJ Emerald Star Bedienungsanleitung

American DJ

American DJ Flat Par Tri18X Bedienungsanleitung

American DJ

American DJ RotoPod Bedienungsanleitung

American DJ

American DJ Jelly Par Profile Bedienungsanleitung

American DJ

American DJ Spektra 250 Bedienungsanleitung

American DJ

American DJ SWEEPER BEAM LED Bedienungsanleitung

American DJ

American DJ SATURN 4 Bedienungsanleitung

American DJ

American DJ Revo I Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung