American DJ Deco 250 Bedienungsanleitung

American DJ

4295 Charter Street

Los Angeles CA. 90058

www.americandj.com

12/03

User Instructions

Unpacking: Thank you for purchasing the Deco 250™ by American

DJ®. Every Deco 250™ has been thoroughly tested and has been

shipped in perfect operating condition. Carefully check the shipping

carton for damage that may have occurred during shipping. If the

carton appears to be damaged, carefully inspect your xture for any

damage and be sure all equipment necessary to operate the unit has

arrived intact. In the event damage has been found or parts are miss-

ing, please contact our toll free customer support number for further

instructions. Do not return this unit to your dealer without rst contact-

ing customer support.

Introduction: This unit uses 11 pieces of individual textured glass

mounted on a wheel and a 11 colored tiles to produce vibrant colors

and extravagant gobo patterns. The Deco 250™ is an intelligent fixture

that can operate in DMX mode, as a stand alone sound active piece,

or in a Master/Slave configuration. The Deco 250™ alsp comes with

several built in programs. This piece is best used with a fog or haze

machine to enhance the beam output. When used in DMX mode the

fixture requires 3 DMX channels. When used as a stand alone unit

or when used in multiples linked in a master/slave configuration an

optional MINI/C controller may be used to control a blackout function.

Customer Support: American DJ® provides a toll free customer sup-

port line, to provide set up help and to answer any question should you

encounter problems during your set up or initial operation. You may

also visit us on the web at www.americandj.com for any comments or

suggestions. Service Hours are Monday through Friday 9:00 a.m. to

5:00 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2610

E-mail: [email protected]

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

American DJ®.

Deco 250™ General Information

©American DJ® - www.americandj.com - Deco 250™ Instruction Manual Page 2

©American DJ® - www.americandj.com - Deco 250™ Instruction Manual Page 3

• ELC 24v/250w Lamp

• DMX-512 Compatible

• 11 Textured Glass Gobos, and 11 Colors

• Fan Cooled.

• Master/Slave Operation

• Linkable

Deco 250™ Main Features

The Deco 250™ carries a one year (365 days) limited warranty.

Please fill out the enclosed warranty card to validate your purchase.

All returned service items whether under warranty or not, must be

freight pre-paid and accompany a return authorization (R.A.) number.

If the unit is under warranty, you must provide a copy of your proof of

purchase invoice. Please contact American DJ® customer support for

a R.A. number.

Deco 250™ Product Registration

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required voltage

for your unit.

• Do not attempt to operate this unit if the power cord has been frayed

or broken.

• Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when itʼs cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product outdoors

voids all warranties.

• During long periods of non-use, disconnect the unitʼs main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 13 for cleaning details.

• Heat -The appliance should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances (includ-

ing amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the appliance.

C. The appliance has been exposed to rain or water.

D. The appliance does not appear to operate normally or exhibits a

marked change in performance.

Deco 250™ Safety Precautions

©American DJ® - www.americandj.com - Deco 250™ Instruction Manual Page 4

To optimize the performance of this product, please read these operat-

ing instructions carefully to familiarize yourself with the basic operations

of this unit. These instructions contain important safety information

regarding the use and maintenance of this unit. If you do not wish to

read through the manual, listed below are the master/slave dipswitch

setting. Link the units together using XLR cables and follow the dip-

switch chart for sound activation mode. Please keep this manual with

the unit, for future reference.

Deco 250™ Quick Start Instructions

Deco 250™ Master/Slave Settings

This chart details the Master/Slave dipswitch setting for Master/Slave

configuration. Use this configuration only when you will be using your

fixtures in a Master/Slave configuration. Be sure the number 2 func-

tion switch is set to the on position for sound-active operation.

©American DJ® - www.americandj.com - Deco 250™ Instruction Manual Page 6©American DJ® - www.americandj.com - Deco 250™ Instruction Manual Page 5

Deco 250™ Controls and Functions

REAR

1. Cooling Fan -

Keep the fan grill clean. Never block the fan vents, always allow at least

four inches between the fan and any other surface. Improper cooling

may result in premature lamp failure.

2. MINI/C Controller Jack -

This is for use the optional MINI/C Black out controller only. Do not

attempt to connect an audio signal this jack, this will damage the

PC board and void your manufactures warranty!

Deco 250™ Controls and Functions

3. Power Cord -

Connect only to a matching power outlet. Never use this xture is the

ground prong has been removed or broken off.

4. XLR Input Jack -

This jack is used to accept an incoming DMX signal or Master/Slave

signal.

5. Breaker -

A 10A built-in safety breaker to reduce the risk of electrical shock or

re and protect the circuitry. In the case of a internal short or power

surge.

6. XLR Output Jack -

This jack is used to transmit the incoming DMX signal to another DMX

xture, or in master/slave mode transmit a Master/Slave signal to the

next Deco 250™ in the chain. For best results in DMX or Master/Slave

mode terminate this jack if it is the last unit in the chain. See “Termina-

tor” on page 11.

7. Audio Sensitivity Knob -

This adjusts audio sensitivity of the INTERNAL MICROPHONE. Turn-

ing the sensitivity knob in the clockwise direction will increase the sen-

sitivity to sound. Turning the knob in the counter clockwise direction

will decrease the xture’s sensitivity to sound.

8. Dipswitches -

These switches serve two functions. In master slave mode these

switches are used to assign a specic head address. In DMX mode

these switches are used to assign a DMX address to the unit. In DMX

mode each switch corresponds to a specic value based on binary

code. See page 7 for a detailed explanation of DMX binary code.

1 8765432









Operating Modes:

You may operate your Deco 250™ in three different ways:

• Stand Alone Mode - The unit will react to sound, chasing through

the built in programs. You may also use the optional MINI/C Remote

to control a blackout function.

• Master/Slave Mode - This mode allows you to daisy chain up to 4

units together to get a synchronized light show that will react to sound

and chase through the several built in programs.

• DMX Mode - This function will allow you to control each individual

fixtures traits with a standard DMX 512 controller such as the LSC®

Show Designer.™

Note: Sound Acitve and Master-Slave operation require sound to acti-

vate! If the units do not move adjust the volume sensitivity knob on the

rear of the xture.

Note: To conserve lamp life, the unit will automatically turn off the lamp

when the xture has been inactive for longer than 60 seconds. This is

not a malfunction and will aid lamp and unit longevity by decreasing

heat.

Stand-Alone Operation (Sound Active): This function allows a

single unit to run to the beat of the music or run any of the built in pro-

grams. Only use this function when running a single unit, or when run-

ning several units as individuals.

1. To activate the Sound-Active mode or a built in program, refer to

the Special Function list on page 15.

2. The unit will now react to the low frequencies of music via the

internal microphone. The unit is preset to activate at a certain

sound pressure level. Occasionally the unit will not react to certain

high pitch sounds.

3. The optional MINI/C Controller may be used with this mode to

control stand-by (blackout).

Master-Slave Operation (Sound Active): This function will allow

you to link up to 4 units together and operate without a controller or with

the MINI/C. The units will react to sound. In Master-Slave operation one

unit will act as the controlling unit and the others will react to the control-

ling units programs. Any unit can act as a Master or as a Slave.

Deco 250™ Operation

©American DJ® - www.americandj.com - Deco 250™ Instruction Manual Page 8©American DJ® - www.americandj.com - Deco 250™ Instruction Manual Page 7

Deco 250™ Operation

1. Using standard XLR microphone cables, daisy chain your units

together via the XLR connector on the rear of the units. Remember

the Male XLR connector is the input and the Female XLR connec-

tor is the output. The rst unit in the chain (master) will use the

female XLR connector only - The last unit in the chain will use the

male XLR connector only. For longer cable runs we suggest a

terminator at the last fixture.

2. Follow the chart on page 15 for proper unit dipswitch settings.

3. The optional MINI/C Controller may be used with this mode to

control stand-by (blackout).

4. After all the units settings have been set and are plugged in, they

will begin to run to sound. If there is no sound present the units

will blackout to preserve and extended lamp life.

Universal DMX Control: This function allows you to use a univer-

sal DMX-512 controller such as the LSC® DMX Operator™ or Show

Designer.™ to control the textured glass gobo wheel, the color arm,

and mirror kit. Using a DMX controller will allow you to customize pro-

grams and expand functionality. Operating through a DMX controller

gives freedom to create unique programs tailored to oneʼs individual

needs.

1. The Deco 250™ uses 3 DMX channels. Channel 1 controls

the textured glass gobo wheel, channel 2 controls the color

arm and channel 3 controls the dichric mirror. See page 14 for

detailed description of the DMX traits.

2. To control your fixture in DMX mode, follow the set-up proce-

dures on pages 9 - 11 as well as the set-up specifications that are

included with your DMX controller. Assign a DMX address to the

unit.

3. Use the controllerʼs faders to control the various DMX fixture traits.

4. This will allow you to create your own programs.

5. For help operating in DMX operation consult the manual included

with your DMX controller.

6. For longer cable runs (more than a 100 feet) use a terminator on

the last fixture.

dipswitch 10 it is used for special functions such as sound activation.

Each dipswitch has a preset value. A specific DMX address is set by

combining the dipswitches that sum your desired value. For example:

To achieve a DMX address of 21, combine dipswitches 1, 3, and 5.

Sense dipswitch 1 has a value of 1, dipswitch 3 has a value of 4, and

dipswitch 5 has a value of 16, the combination of the create a DMX

value of 21.

Set DMX address 21: Set DMX address 201:

Dipswitch # 1 = 1 Dipswitch # 1 = 1

Dipswitch # 3 = 4 Dipswitch # 4 = 8

Dipswitch # 5 = 16 Dipswitch # 7 = 64

= 21 Dipswitch # 8 = 128

= 201

Data Cable (DMX Cable) Requirements (For DMX and Master/

Slave Operation): The Deco 250™ can be controlled via DMX-512

protocol. The American DJ® Deco 250™ is a three channel DMX unit.

The DMX address is set on the back panel of the Deco 250™. Your unit

and your DMX controller require a standard 3-pin

XLR connector for data input and data output

(Figure 1). If you are making your own cables, be

sure to use standard two conductor shielded cable

(This cable may be purchased at almost all pro

sound and lighting stores). Your cables should be

made with a male and female XLR connector on

either end of the cable. Also remember that DMX

cable must be daisy chained and can not be split.

©American DJ® - www.americandj.com - Deco 250™ Instruction Manual Page 10

©American DJ® - www.americandj.com - Deco 250™ Instruction Manual Page 9

Power Supply: Before plugging your unit in, be sure the source volt-

age in your area matches the required voltage for your American DJ®

Deco 250.™ The American DJ® Deco 250™ is available in a 120v and

220v version. Because line voltage may vary from venue to venue,

you should be sure your unit voltages matches the wall outlet voltage

before attempting to operate you xture.

DMX-512: DMX is short for Digital Multiplex. This is a universal

protocol used as a form of communication between intelligent fixtures

and controllers. A DMX controller sends DMX data instructions from

the controller to the fixture. DMX data is sent as serial data that

travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR

terminals located on all DMX fixtures (most controllers only have a

DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of

different manufactures to be linked together and operate from a single

controller, as long as all xtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX

fixtures try to use the shortest cable path possible. The order in which

fixtures are connected in a DMX line does not influence the DMX

addressing. For example; a fixture assigned a DMX address of 1 may

be placed anywhere in a DMX line, at the beginning, at the end, or

anywhere in the middle. When a fixture is assigned a DMX address of

1, the DMX controller knows to send DATA assigned to address 1 to

that unit, no matter where it is located in the DMX chain.

Dip-switches in DMX mode: This unit uses dipswitches to assign a

DMX address. Each dipswitch represents a binary value.

Dipswitch 1 address equals 1

Dipswitch 2 address equals 2

Dipswitch 3 address equals 4

Dipswitch 4 address equals 8

Dipswitch 5 address equals 16

Dipswitch 6 address equals 32

Dipswitch 7 address equals 64

Dipswitch 8 address equals 128

Dipswitch 9 address equals 256

Dipswitch 10 - Some units omit dipswitch 10. When a unit does include

Deco 250™ Set Up

ON 1 98765432 10

1282 8 32

256651641

DMX CHANNEL

Figure 1

Deco 250™ Set Up

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cableʼs shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLRʼs outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Deco 250™ Lamp Replacement

©American DJ® - www.americandj.com - Deco 250™ Instruction Manual Page 11 ©American DJ® - www.americandj.com - Deco 250™ Instruction Manual Page 12

Caution: Always replace with the exact same type lamp, unless oth-

erwise specified by an authorized American DJ® technician. Replace

with anything other than the specified part can damage your unit and

will void your manufactures warranty.

Warning: If you continue to blow either the lamp or the breaker,

STOP using the unit. Contact customer support for further instruc-

tions, you may have to return the unit for servicing. Continuing to use

the unit may cause serious damage.

Breaker Reset: This unit is equipped with a built-in safety breaker.

This breaker is designed to close the power circuit in the event of an

internal short or power surge. This will reduce the risk of electrical

shock or re and protect the circuitry. To reset the breaker, push the

breaker button in until you hear it “pop” back in to place. If the break-

er continues to pop, stop using the unit and contact our customer

support team, the unit may need to be returned for service.

Lamp Replacement: Caution! Never attempt to change the lamp

while the fixture is plugged in. Always disconnect the main power

and allow the unit ample time to cool before attempting to replace the

lamp. Lamp replacement has been made simple by incorporating the

use of a flip-up front cover that is retained by a thumb screw.

1. Be sure to follow the proper handling procedures that deal with

halogen lamps.

2. Remove the thumb screw on the top of the unit.

3. After removing the thumb screw, pull off socket assembly protec-

tive cover.

4. Carefully remove the old lamp and discard it in the trash.

5. Replace the lamp with an exact match and reassemble in reverse order.

Deco 250™ Set Up

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number ZDMX/T) will decrease the possibilities of erratic

behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin XLR

connectors for DATA transmission in place of 3-pin. 5-pin XLR xtures

may be implemented in a 3-pin XLR DMX line. When inserting standard

5-pin XLR connectors in to a 3-pin line a cable adaptor must be used,

these adaptors are readily available at most electric stores. The chart

below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Halogen Lamp Warning: This fixture is fitted

with halogen lamps which are highly susceptible

to damage if improperly handled. Never touch the

lamps with your bare fingers as the oil from your

hands will shorten lamp life. Also, never move the

fixture until the lamps have had ample time to cool.

Remember, lamps are not covered under warranty

conditions.

©American DJ® - www.americandj.com - Deco 250™ Instruction Manual Page 14

Deco 250™ Cleaning

Deco 250™ Trouble Shooting

Fixture Cleaning: Due to fog residue, smoke, and dust cleaning the

internal and external optical lenses and mirror should be carried out

periodically to optimize light output. Cleaning frequency depends on

the environment in which the fixture operates (I.e. smoke, fog residue,

dust, dew). In heavy club use we recommend cleaning on a monthly

basis. Periodic cleaning will ensure longevity, and crisp output.

1. Use normal glass cleaner and a soft cloth to wipe down the outside

casing.

2. Use a brush to wipe down the cooling vents and fan grill.

3. Clean the external optics and mirror with glass cleaner and a soft

cloth every 20 days.

4. Clean the internal optics with glass cleaner and a soft cloth every

30-60 days.

5. Always be sure to dry all parts completely before plugging the unit

back in.

Trouble Shooting: Listed below are a few common problems that you

may encounter, with solutions.

No light output from the unit;

1. Be sure you have connected your unit into a wall outlet with a

matching power supply.

2. Be sure the breaker has not blown. The breaker is located on the

rear panel of the unit.

3. Remove the lamp cover and be sure the lamp is seated in its

socket properly. Occasionally lamps become loose during shipping

be sure the lamp is push in to its socket all the way.

Unit does not respond to sound;

1. Low frequencies (bass) should cause the unit to react to sound.

Tapping on the microphone, quiet or high pitched sounds may not

activate the unit.

©American DJ® - www.americandj.com - Deco 250™ Instruction Manual Page 13

Deco 250™ DMX Traits

Channel Value Function

1 0 - 255 TEXTURED GLASS GOBO

0 OFF

01 - 21 SPOT

22 - 43 GOBO 1

44 - 65 GOBO 2

66 - 87 GOBO 3

88 - 109 GOBO 4

110 - 131 GOBO 5

132 - 153 GOBO 6

154 - 175 GOBO 7

176 - 197 GOBO 8

198 - 219 GOBO 9

220 - 241 GOBO 10

242 - 254 GOBO 11

255 GOBO WHEEL ROTATION

2 0 - 255 COLOR ARM

0 BLACKOUT

01 MULTI-COLOR 1

MULTI-COLOR 2

MULTI-COLOR 3

MULTI-COLOR 4

MULTI-COLOR 5

MULTI-COLOR 6

MULTI-COLOR 7

MULTI-COLOR 8

MULTI-COLOR 9

MULTI-COLOR 10

254 MULTI-COLOR 11

255 RAINBOW EFFECT

©American DJ® - www.americandj.com - Deco 250™ Instruction Manual Page 15

Deco 250™ Special Functions List

  









 

 







 



  

 



 



















      

 

   

   

 

  



 

   

   

   

   

   

   



 





   





   







 

      







 

   







 

 

 

MASTER/SLAVE DIPSWITCH SETTINGS

Channel Value Function

3 0 - 255 MIRROR

0 STOP

01 - 127 COUNTER-CLOCKWISE ROTATION

FAST SLOW

128 STOP

129 - 255 CLOCKWISE ROTATION

SLOW FAST

Deco 250™ DMX Traits

A Division of the American DJ® Group of Companies

4295 Charter Street Los Angeles, CA 90058 USA

Tel: 323-582-2650 Fax: 323-582-2610

Web: www.americandj.com E-mail: [email protected]

Technical Specifications:

Model: Deco 250™

Lamps: LL-ELC, 24v/250w

Voltage: 120v~60Hz / 220v~50/60Hz

Dimensions: 10.3” x 9.5” x 5”

262mm x 240mm x 130mm

Colors: 11

Textured Glass: 11, Plus Spot

Weight: 12.76 Lbs. / 5.8 Kgs

Breaker: 10A

Duty Cycle: None

DMX: 2 Channels

Sound Active: Yes

Working Position: Any Safe, Secure Position

Warranty: 1 Year (365 days)

Please Note: Specications and improvements in the design

of this unit and this manual are subject to change without any

prior written notice.

Deco 250™ Warranty

1-YEAR LIMITED WARRANTY

A. American DJ® hereby warrants, to the original purchaser, American DJ® products to be

free of manufacturing defects in material and workmanship for a period of 1 Year (365 days)

from the date of purchase. This warranty shall be valid only if the product is purchased

within the United States of America, including possessions and territories. It is the owner’s

responsibility to establish the date and place of purchase by acceptable evidence, at the

time service is sought.

B. For warranty service, send the product only to the American DJ® factory. All shipping

charges must be pre-paid. If the requested repairs or service (including parts replacement)

are within the terms of this warranty, American DJ® will pay return shipping charges only

to a designated point within the United States. If the entire instrument is sent, it must be

shipped in its original package. No accessories should be shipped with the product. If any

accessories are shipped with the product, American DJ® shall have no liability whatsoever

for loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is

modied in any manner which American DJ® concludes, after inspection, affects the reli-

ability of the product; if the product has been repaired or serviced by anyone other than

the American DJ® factory unless prior written authorization was issued to purchaser by

American DJ®; if the product is damaged because not properly maintained as set forth in

the instruction manual.

D. This is not a service contract, and this warranty does not include maintenance, cleaning

or periodic check-up. During the period specied above, American DJ® will replace defec-

tive parts at its expense, and will absorb all expenses for warranty service and repair labor

by reason of defects in material or workmanship. The sole responsibility of American DJ®

under this warranty shall be limited to the repair of the product, or replacement thereof,

including parts, at the sole discretion of American DJ®. All products covered by this war-

ranty were manufactured after January 1, 1990, and bear identifying marks to that effect.

E. American DJ® reserves the right to make changes in design and/or improvements upon

its products without any obligation to include these changes in any products theretofore

manufactured.

F. No warranty, whether expressed or implied, is given or made with respect to any acces-

sory supplied with products described above. Except to the extent prohibited by applicable

law, all implied warranties made by American DJ® in connection with this product, includ-

ing warranties of merchantability or tness, are limited in duration to the warranty period

set forth above. And no warranties, whether expressed or implied, including warranties of

merchantability or tness, shall apply to this product after said period has expired. The

consumer’s and or Dealer’s sole remedy shall be such repair or replacement as is expressly

provided above; and under no circumstances shall American DJ® be liable for any loss or

damage, direct or consequential, arising out of the use of, or inability to use, this product.

G. This warranty is the only written warranty applicable to American DJ® Products and

supersedes all prior warranties and written descriptions of warranty terms and conditions

heretofore published.

H. Lamps are not covered under this or any other warranty, either written or implied.

Inhaltsverzeichnis

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ Quick Scan Sys Bedienungsanleitung

American DJ

American DJ Lotus Bedienungsanleitung

American DJ

American DJ DJ Scan/RG Bedienungsanleitung

American DJ

American DJ SWEEPER BEAM QUAD LED Bedienungsanleitung

American DJ

American DJ Super Jewel Bedienungsanleitung

American DJ

American DJ Shooting Star LED Bedienungsanleitung

American DJ

American DJ Royal 3D Bedienungsanleitung

American DJ

American DJ DJ Scan 250 Bedienungsanleitung

American DJ

American DJ Galaxian Move Bedienungsanleitung

American DJ

American DJ Color Flash 4 Bedienungsanleitung

American DJ

American DJ Rolling Star II Bedienungsanleitung

American DJ

American DJ Snow Flurry Montageanleitung

American DJ

American DJ MINI-Gressor II Bedienungsanleitung

American DJ

American DJ Fusion FX Bar 4 Bedienungsanleitung

American DJ

American DJ Color Shot Bedienungsanleitung

American DJ

American DJ X-CALIBUR Bedienungsanleitung

American DJ

American DJ SATURN 4 Bedienungsanleitung

American DJ

American DJ Dynasty Scan DMX Bedienungsanleitung

American DJ

American DJ Punch LED PRO Bedienungsanleitung

American DJ

American DJ Tempest II/AS Bedienungsanleitung

American DJ

American DJ Roto-Balls VS MKII Bedienungsanleitung

American DJ

American DJ T4 Bedienungsanleitung

American DJ

American DJ Revo Roll LED Bedienungsanleitung

American DJ

American DJ Vortex Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung