American DJ Fusion FX Bar 4 Bedienungsanleitung

Fusion FX Bar 4

UserGuide

Professional Entertainment Technology

TABLE OF CONTENTS

1. Safety Instruction

2. Technical Specification

3. How To Set The Unit

4. How To Control The Unit

5. Troubleshooting

6. Fixture Cleaning

1. Safety Instruction

WARNING

yPlease keep this User Guide for future consultation. If you sell the unit to another user, be

sure that they also receive this instruction booklet.

yUnpack and check carefully there is no transportation damage before using the unit.

yBefore operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

yIt’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

yThe unit is for indoor use only. Use only in a dry location.

yThe unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that no ventilation slots are blocked.

yDisconnect main power before replacement or servicing.

yMake sure there is no flammable materials close to the unit while operating as it is fire

hazard.

yMaximum ambient temperature is TA: 40℃. Don’t operate it where the temperature is

higher than this.

yIn the event of serious operating problem, stop using the unit immediately. Never try to

repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or

malfunction. Please contact the nearest authorized technical assistance center. Always

use the same type spare parts.

yDo not touch any wire during operation as high voltage might be causing electric shock.

Warning

yTo prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

yThe housing or the lenses must be replaced if they are visibly damaged.

Caution

There are no user serviceable parts inside the unit. Do not open the housing or attempt

any repairs yourself. In the unlikely event your unit may require service, please contact

your nearest dealer.

Please read carefully the instruction, which includes important information

about the installation, usage and maintenance.

Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the

unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the

structure to which you are attaching the unit is secure and is able to support a 10 times

weight of the unit.

2. Technical Specification

yVoltage：AC 100-240V~50/60Hz

yPower Consumption: 22.6W

yLight Source:

LED: 3W x 90pcs White +1pc Tri-color

Laser Power: Green 5mW

yFuse: T 3.15A

yDimension: 542 x 143 x 194 mm

yWeight: 3.7 kg

3. How To Set The Unit

3.1 Control Panel

Display

To show the various menus and the selected functions

LED

DMX On DMX input present

MASTER On Master Mode

SLAVE On Slave Mode

SOUND Flashing Sound activation

Button

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

DMX input/output

For DMX512 link, use 3-pin XLR plug cable to link the unit together.

Remote control

By connect to the 1/4’’ microphone jack to control the unit for Stand by, Function and Mode

function.

Sensitivity

To adjust the sound receiving sensitivity

Power input/output

Connecting for mains power

3.2 Main Function

To select any of the given functions, press the MENU button up to when the required one is

showing on the display. Select the function by ENTER button and the display will blink. Use

DOWN and UP button to change the mode. Once the required mode has been selected,

press the ENTER button to setup or it will automatically return to the main functions without

any change after idling 8 seconds. To go back to the functions without any change press the

MENU button. The main functions are showing below:

DMX 512Address Setting

Press the MENU button up to when the is showing on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to change the DMX512 address.

Once the address has been selected, press the ENTER button to store or it will

automatically return to the main functions without any change after idling 8 seconds. To go

back to the main functions without any change press the MENU button.

ShowMode

Press the MENU button up to when the is showing on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select the (random

show) or (show 1) or …(show 6). Once the show has been selected,

press the ENTER button to store or it will automatically return to the main functions without

any change after idling 8 seconds. To go back to the main functions without any change

press the MENU button.

Show 1 – Moon flower show

Show 2 – Ø5 LED show

Show 3 – Laser show

Show 4 – Ø5 LED and Moon flower show

Show 5 –Laser and Ø5 LED show

Show 6 –Laser and moon flower show

Master/Slave Mode

Press the MENU button up to when the is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to select the

(master mode) or (slave 1 mode) or (slave 2 mode). Once the mode has

been selected, press the ENTER button to store or it will automatically return to the main

functions without any change after idling 8 seconds. To go back to the main functions

without any change press the MENU button.

Sound Mode

Press the MENU button until the is showing on the display. Pressing ENTER button

and the display will blink. Use DOWN and UP button to select the (sound on) or

(sound off) mode. Once the mode has been selected, press the ENTER button to

store or it will automatically return to the main functions without any change after idling 8

seconds. To go back to the main functions without any change press the MENU button.

Blackout Mode

Press the MENU button up to when the is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to select the

(blackout) or (no blackout) mode. Once the mode has been selected, press the

ENTER button to store or it will automatically return to the main functions without any

change after idling 8 seconds. To go back to the main functions without any change press

the MENU button.

Led Display

Press the MENU button up to when the is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to select the

(Led on) or (Led off) mode. Once the mode has been selected, press the ENTER

button to store or it will automatically return to the main functions without any change after

idling 8 seconds. To go back to the main functions without any change press the MENU

button.

Display Inversion

It is good for you to install the unit on the floor or under ceiling. Press the MENU button up to

when the is blinking on the display, press ENTER button to confirm. Use DOWN

and UP button to change to the mode (display normal) or (display

inversion), press the ENTER button to store or it will automatically return to the main

functions without any change after idling 8 seconds. To go back to the main functions

without any change press the MENU button.

Self-Test

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and the unit will run self-test by built-in program. To go back to the functions press the

MENU button again.

Fixture Hours

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and the display will show the number of working hours of the unit. To go back to the

functions press the MENU button again.

Software version

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and the display will show the version of software of the unit. To go back to the

functions press the MENU button again.

Reset

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and all channels of the unit will return to their standard position. To go back to the

functions without any change press the MENU button again.

4. How To Control The Unit

You can operate the unit in three ways:

1. By master/slave built-in preprogram function

2. By easy controller

3. By universal DMX controller

No need to turn the unit off when you change the DMX address, as new DMX address

setting will be effected at once. Every time you turn the unit on, it will show on the

display, after that the unit will be ready to receive DMX signal or run the built in programs.

4.1 Master/Slave Built In Preprogrammed Function

By linking the units in master/slave connection, the first unit will control the other units to

give an automatic, sound activated, synchronized light show. This function is good when you

want an instant show. You have to set the first unit in (master mode) and select

(show 0) or (show 1) or … or (show 6). Its DMX input jack will

have nothing plugged into it, Its master LED will be constantly on and sound LED will flash to

the music. The other units will have to set in (slave 1 mode) or (slave 2

mode), Their DMX cables plugged into the DMX input jacks (daisy chain) and the slave led

lights will constantly on.

2-light show

In slave mode, means the unit works normally and means 2-light show. In

order to create a great light show, you can set on the second unit to get contrast

movement to each other, even if you have two units only.

4.2 Easy Controller

The easy remote control is used only in master/slave mode. By connecting to the 1/4”

microphone jack of the first unit, you will find that the remote control on the first unit will

control all the other units functions press the MENU button again.

Stand By Blackout the unit

Function 1. Ø 5 LED Strobe

2. Moon flower strobe

Select show

Show1-6

Mode Sound (LED OFF) LED ON

4.3 DMX Controller

Using universal DMX controller to control the units, you have to set DMX address from 1 to

512 channel so that the units can receive DMX signal.

Press the MENU button up to when the is showing on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to change the DMX512 address.

Once the address has been selected, press the ENTER button to store or it will

automatically return to the main functions without any change after idling 8 seconds. To go

back to the main functions without any change press the MENU button. Please refer to the

following diagram to address your DMX512 channel for the first 4 units：

4.4 DMX 512 Configuration

4.5 DMX512 Connection

The DMX 512 is widely used in intelligent lighting control, with a maximum of 512 channels.

1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin

adapter-cable.

2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm

1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it

in the DMX-output of the last unit.

3. Connect the unit together in a `daisy chain` by XLR plug from the output of the unit to

the input of the next unit. The cable can not branched or split to a `Y` cable. DMX 512 is

a very high-speed signal. Inadequate or damaged cables, soldered joints or corroded

connectors can easily distort the signal and shut down the system.

4. The DMX output and input connectors are pass-through to maintain the DMX circuit,

when power is disconnected to the unit.

5. Each lighting unit needs to have an address set to receive the data sent by the

controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).

6. The end of the DMX 512 system should be terminated to reduce signal errors.

7. 3 pin XLR connectors are more popular than 5 pin XLR.

3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

Pin 4/5: Not used.

5. Troubleshooting

Following are a few common problems that may occur during operation. Here are

some suggestions for easy troubleshooting:

A. The unit does not work, no light and the fan does not work

1. Check the connection of power and main fuse.

2. Measure the mains voltage on the main connector.

3. Check the power on LED.

B. Not responding to DMX controller

1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.

2. If the DMX LED is on and no response to the channel, check the address settings and

DMX polarity.

3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB

of the unit or the previous one.

4. Try to use another DMX controller.

5. Check if the DMX cables run near or run alongside to high voltage cables that may

cause damage or interference to DMX interface circuit.

C. Some units don’t respond to the easy controller

1. You may have a break in the DMX cabling. Check the LED for the response of the

master/ slave mode signal.

2. Wrong DMX address in the unit. Set the proper address.

D. No response to the sound

1. Make sure the unit does not receive DMX signal.

2. Check microphone to see if it is good by tapping the microphone

6. Fixture Cleaning

The cleaning of internal and external optical lenses and/or mirrors must be carried out

periodically to optimize light output. Cleaning frequency depends on the environment in

which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater

accumulation of dirt on the unit’s optics.

yClean with soft cloth using normal glass cleaning fluid.

yAlways dry the parts carefully.

yClean the external optics at least every 20 days. Clean the internal optics at least every

30/60 days.

EC Declaration of Conformity

We declare that our products (lighting equipments) comply with the

following specification and bears CE mark in accordance with the

provision of the Electromagnetic Compatibility (EMC) Directive

89/336/EEC.

EN55014-2: 1997A1: 2001, EN61000-4-2: 1995; EN61000-4-3: 2002;

EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6: 1996,

EN61000-4-11: 1994.

Harmonized Standard

EN60598-1: 2000+ALL: 2000+A12: 2002

Safety of household and similar electrical appliances

Part 1: General requirements

Innovation, Quality, Performance

Andere Handbücher für Fusion FX Bar 4

Inhaltsverzeichnis

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ H2O 250 Montageanleitung

American DJ

American DJ Vizi Scan LED PRO Bedienungsanleitung

American DJ

American DJ Flight-Moon Bedienungsanleitung

American DJ

American DJ Mega Pixel LED Bedienungsanleitung

American DJ

American DJ SS-DMX19CTM Bedienungsanleitung

American DJ

American DJ Snow Flurry Bedienungsanleitung

American DJ

American DJ Aggressor Tri LED Bedienungsanleitung

American DJ

American DJ Onyx II Bedienungsanleitung

American DJ

American DJ LED Vision Bedienungsanleitung

American DJ

American DJ Concept Color Bedienungsanleitung

American DJ

American DJ DJ Scan 250 Bedienungsanleitung

American DJ

American DJ Accu Scan 250 Montageanleitung

American DJ

American DJ LED Beam Scan Bedienungsanleitung

American DJ

American DJ Super Jewel Bedienungsanleitung

American DJ

American DJ Roto-Balls VS MKII Bedienungsanleitung

American DJ

American DJ X-Scan LED Plus Bedienungsanleitung

American DJ

American DJ Flat Par Tri7X Bedienungsanleitung

American DJ

American DJ Revo Sweep Bedienungsanleitung

American DJ

American DJ H2O LED Bedienungsanleitung

American DJ

American DJ PDP-800 Bedienungsanleitung

American DJ

American DJ Color Flash 4 Bedienungsanleitung

American DJ

American DJ Accu Spot 250 Hybrid Bedienungsanleitung

American DJ

American DJ Snow Flurry Montageanleitung

American DJ

American DJ DP-DMX-20L Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung