American DJ Fun Factor LED Bedienungsanleitung

12/11

User Instructions

American DJ®- www.americandj.com - Fun Factor LED Instruction Manual Page 2

Fun Factor LED General Information

Unpacking: Thank you for purchasing the Fun Factor LED by Ameri-

can DJ®. Every Fun Factor LED has been thoroughly tested and has

been shipped in perfect operating condition. Carefully check the ship-

ping carton for damage that may have occurred during shipping. If the

carton appears to be damaged, carefully inspect your xture for any

damage and be sure all equipment necessary to operate the unit has

arrived intact. In the event damage has been found or parts are miss-

ing, please contact our toll free customer support number for further

instructions. Please do not return this unit to your dealer without con-

tacting customer support rst.

Introduction: The Fun Factor LED is a intelligent, multi-LED scanner.

The Fun Factor LED can operate as a stand alone fixture or in a Master/

Slave configuration. The Fun Factor LED has three operating modes;

sound active mode, show mode, and DMX control. For best results use

fog or special effects smoke to enhance the beams projections.

Customer Support: American DJ®provides a toll free customer

support line, to provide help and to answer any question should you

encounter problems during your set up or initial operation. You may

also visit us on the web at www.americandj.com for any comments or

suggestions. Service Hours are Monday through Friday 8:00 a.m. to

4:30 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: [email protected]

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Warning! This may cause severe eye damage. Avoid looking directly

into the light source at all times!

For Your Own Personal Safety, Please Read and Understand This

Manual Completely Before You Attempt To Install Or Operate

This Unit!

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt-

age for your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken.

• Do not attempt to remove or break o the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 21 for cleaning details.

• Heat -This fixture should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including

amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. Objects have fallen, or liquid has been spilled into the appliance.

B. The appliance has been exposed to rain or water.

C. The appliance does not appear to operate normally or exhibits a

marked change in performance.

Fun Factor LED Safety Precautions

American DJ®- www.americandj.com - Fun Factor LED Instruction Manual Page 4American DJ®- www.americandj.com - Fun Factor LED Instruction Manual Page 3

• DMX-512 Protocol Compatible (1, 4, or 8 DMX Channels)

• X/Y Mirror Control

• 3 Operating Modes - Sound Active, Show Mode, and DMX Control

• Internal Microphone

• Digital Display for Address and Function Setting

• UC3 Controller (Not Included)

Fun Factor LED Features

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

American DJ®.

American DJ®will not accept any liability for any resulting damages

caused by the non-observance of this manual or any unauthorized

modication to this unit.

Fun Factor LED Handling Precautions

Fun Factor LED Warranty Registration

The Fun Factor LED carries a 3 year (1095 days) limited warranty.

Please fill out the enclosed warranty card to validate your purchase

and warranty. You may also register your product online at www.

americandj.com. All returned service items whether under warranty or

not, must be freight pre-paid and accompany a return authorization

(R.A.) number. If the unit is under warranty you must provide a copy

of your proof of purchase invoice. Please contact American DJ® cus-

tomer support for a R.A. number.

To optimize the performance of this product, please read these

operating instructions carefully to familiarize yourself with the basic

operations of this unit. These instructions contain important safety

information regarding the use and maintenance of this unit. Please

keep this manual with the unit, for future reference.

Fun Factor LED General Instructions

American DJ®- www.americandj.com - Fun Factor LED Instruction Manual Page 6American DJ® - www.americandj.com - Fun Factor LED Instruction Manual Page 5

Power Supply: The American DJ®Fun Factor LED contains a auto-

matic voltage switch, which will auto sense the voltage when it is

plugged into the power source. With this switch there is no need to

worry about the correct power voltage, this unit can be plugged in

anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used by most lighting and controller manufactures as a form of

communication between intelligent fixtures and controllers. A DMX

controller sends DMX data instructions from the controller to the fix-

ture. DMX data is sent as serial data that travels from fixture to fixture

via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX

fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models

of dierent manufactures to be linked together and operate from a

single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using

several DMX fixtures try to use the shortest cable path possible. The

order in which fixtures are connected in a DMX line does not influence

the DMX addressing. For example; a fixture assigned a DMX address

of 1 may be placed anywhere in a DMX line, at the beginning, at the

end, or anywhere in the middle. Therefore, the first fixture controlled

by the controller could be the last fixture in the chain. When a fixture

is assigned a DMX address of 1, the DMX controller knows to send

DATA assigned to address 1 to that unit, no matter where it is located

in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX and Master/Slave

Operation): The Fun Factor LED can be controlled via DMX-512 proto-

col. The Fun Factor LED can be a 1, 4, or 8 channel

DMX unit. The DMX address is set electronically

using the controls on the rear panel of the unit. Your

unit and your DMX controller require a approved

DMX-512 110 Ohm Data cable for data input and

data output (Figure 1). We recommend Accu-Cable

DMX cables. If you are making your own cables, be

sure to use standard 110-120 Ohm shielded cable

(This cable may be purchased at almost all profes-

sional sound and lighting stores). Your cables should be made with

Fun Factor LED Set Up

Figure 1

Fun Factor LED Hanging Precautions

Fixture installation must always be secured with a secondary

safety attachment, such as an appropriate safety cable.

Regardless of the rigging option you choose for your Fun

Factor LED always be sure to secure your xture with a safety

cable (not included). Attach a safety cable to the provided

safety bolt.

Caution: For added protection mount the xtures in areas out-

side of walking paths, seating areas, or areas were the xture

might be reached by unauthorized personal.

Before mounting the xture to any surface, make sure that the

installation area can hold a minimum point load of 10 times the

device’s weight.

To avoid injury, never stand directly below the device when

mounting, removing, or servicing the xture.

Always use and install a safety cable ( not included) as a safety

measure to prevent accidental damage and/or injury in the

event the clamp fails.

Be sure to complete all rigging and installation procedures

before connecting the main power cord to the appropriate wall

outlet.

American DJ®- www.americandj.com - Fun Factor LED Instruction Manual Page 7 American DJ®- www.americandj.com - Fun Factor LED Instruction Manual Page 8

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX

xtures may be implemented in a 3-pin DMX line. When inserting stan-

dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,

these adaptors are readily available at most electric stores. The chart

below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Pin 5 - Do Not Use

Pin 4 - Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Fun Factor LED Set Up

a male and female XLR connector on either end of the cable. Also

remember that DMX cable must be daisy chained and cannot be split.

Fun Factor LED Set Up

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

American DJ®- www.americandj.com - Fun Factor LED Instruction Manual Page 10American DJ® - www.americandj.com - Fun Factor LED Instruction Manual Page 9

Fun Factor LED System Menu

System Menu: When making adjustments press ENTER

to conrm your setup and then press and hold the MENU

button for at least 3 seconds. To exit without making any

adjustments press the MENU button.

ADDR - DMX Address Setting.

1. Press the either the MENU, UP, or DOWN buttons until

“ADDR” is displayed, press ENTER.

2. The current address will now be displayed and ashing.

Press the UP or DOWN buttons to nd your desired address.

Press ENTER and then press and hold the MENU button to set

your desired DMX address.

CHND - This will let select your desired DMX channel

mode.

1. Press the either the MENU button until “CHND” is displayed,

press ENTER. Either “1CH”, “4CH” or “8CH” will be displayed

2. Press the UP or DOWN buttons to choose your desired DMX

mode and press ENTER to conm and exit.

SLND - This will let you set unit as a master or slave in a

master/slave conguration.

1. Press the MENU button until “SLND” is displayed, press

ENTER. Either “MAST”, “SL 1” or “SL 2” will be displayed.

2. Press the UP or DOWN buttons until your desired setting is

displayed, press ENTER and then press and hold the MENU

button to conm.

NOTE: In a Master/Slave conguration you can set one xture

to Master and then set the next xture to “SL 2”, the xtures will

now have contrast movement to each other.

Fun Factor LED System Menu Chart

American DJ®- www.americandj.com - Fun Factor LED Instruction Manual Page 11 American DJ®- www.americandj.com - Fun Factor LED Instruction Manual Page 12

2. To activate Blackout tap the UP or DOWN buttons until “Yes”

is displayed, press ENTER to conm. The xture will now be in

Blackout mode. To deactivate Blackout mode, select “No” and

press Enter.

LED - With this function you can have the LED display

turn off after 10 seconds.

1. Press the MENU button until “LED” is displayed, press

ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or

DOWN buttons to select “ON” to keep the LED display on at

all times, or “OFF” to switch to have the LED display switch o

after 10 seconds.

3. Press ENTER to conrm.

DISP - This will “ip” the LED display 180º.

1. Press the MENU button until “dISP” is displayed, press ENTER.

2. Either “dISP” or “dSIP” will now be displayed. Press the MENU

button to “ip” the display.

TEST - This function will run a self test program.

1. Press the MENU button until “TEST” is displayed, press

ENTER.

2. The xture will now run a self test.

FHRS - With this function you can display the running time

of the xture.

1. Press the MENU button until “FHRS” is displayed, press

ENTER.

Fun Factor LED System Menu

SHND: SH 0-SH12 - Show modes 0-12 (Factory programs).

Show mode can run with or without sound active mode.

1. Press the MENU button until “SHND” is displayed, press ENTER.

2. “Sh X” will now be displayed, “X” representing a number

between 0-12. Programs 0-12 are factory programs, while “Sh

0” is random mode. Press the UP or DOWN buttons to nd your

desired show.

3. When you have found your desired show press ENTER, then

press and hold the MENU button for at least 3 seconds to acti-

vate.

SOUN - Sound Active mode.

1. Press the MENU button until “SOUN” is displayed, press

ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or

DOWN buttons to select “ON” to activate sound active mode, or

“OFF” to deactivate sound active mode.

3. Press ENTER, and then press and hold the MENU button for

at least 3 seconds to activate.

SENS - Sound sensitivity control.

1. Press the MENU button until “SENS” is displayed, press ENTER.

2. The display will show a number between 0-100. Press the UP or

DOWN buttons to adjust the sound sensitivity. 0 being the least sen-

sitive and 100 the most sensitive.

3. Press the ENTER button to conrm.

BLND - Blackout or Stand by mode.

1. Press the MENU button until “BLND” is displayed, press

ENTER. Either Yes or No will be displayed.

Fun Factor LED System Menu

American DJ®- www.americandj.com - Fun Factor LED Instruction Manual Page 13 American DJ®- www.americandj.com - Fun Factor LED Instruction Manual Page 14

Operating Modes: The Fun Factor LED can operate in three

different modes. In each mode you can run the fixture as a

stand alone fixture or in a master/slave confiugration. This next

section will detail the differences in the operating modes.

• Sound Active mode -

The fixture will react to sound, chasing through the built-in programs.

• Show mode -

Choose 1 of 12 show modes to run.

•DMX control mode -

This function will allow you to control each individual fixtures traits

with a standard DMX-512 controller such as the Elation®Show

Designer.™

Master-Slave Operation This function will allow you to link up to 16

units together and operate without a controller. The units will be sound

activated. In Master-Slave operation one unit will act as the controlling

unit and the others will react to the controlling units programs. Any unit

can act as a Master or as a Slave.

1. Using approved DMX data cables, daisy chain your units togeth-

er via the XLR connector on the rear of the units. Remember the

Male XLR connector is the input and the Female XLR connector

is the output. The rst unit in the chain (master) will use the female

XLR connector only - The last unit in the chain will use the male

XLR connector only. For longer cable runs we suggest a termina-

tor at the last fixture.

2. Set the Master unit to your desired operating mode.

3. For the slave units press the MENU button until “SLND” is dis-

played, and Press ENTER. Set the slave units to either “SL 1” or

“SL 2”.

4. The slave units will now follow the Master unit.

Universal DMX Control: This function allows you to use a Elation®

universal DMX-512 controller to control the chases and patterns,

dimmer and strobe. A DMX controller allows you to create unique

programs tailored to your individual needs.

1. The Fun Factor LED can be a 1, 4, or 8 DMX channel fixture.

See pages 16-20 for detailed description of the DMX values and

traits.

Fun Factor LED Operation

2. The running time of the xture will now be displayed. Press

MENU to exit.

VER - With this function you can display the version soft-

ware of the xture.

1. Tap the MENU button until “VER” is displayed, press ENTER.

2. The software version will now be displayed. Press MENU to

exit.

Fun Factor LED System Menu

American DJ®- www.americandj.com - Fun Factor LED Instruction Manual Page 16American DJ® - www.americandj.com - Fun Factor LED Instruction Manual Page 15

Fun Factor LED 1 DMX Channel Mode

Channel Value Function

1 SHOWS

0 - 7 BLACKOUT

8 - 27 SHOW 1

28 - 47 SHOW 2

48 - 67 SHOW 3

68 - 87 SHOW 4

88 - 107 SHOW 5

108 - 127 SHOW 6

128 - 147 SHOW 7

148 - 167 SHOW 8

168 - 187 SHOW 9

188 - 207 SHOW 10

208 - 227 SHOW 11

228 - 247 SHOW 12

248 - 255 SOUND ACTIVE

Fun Factor LED Operation

2. To control your fixture in DMX mode, follow the set-up procedures

on pages 6-8 as well as the set-up specifications that are includ-

ed with your DMX controller.

3. Use the controller’s faders to control the various DMX fixture traits.

4. This will allow you to create your own programs.

5. Follow the instructions on page 10 to set the DMX address.

6. For longer cable runs (more than a 100 feet) use a terminator on

the last fixture.

7. For help operating in DMX mode consult the manual included

with your DMX controller.

Sound Active Mode: This mode allows either single unit or several

units linked together, to run to the beat of the music.

1. Tap the MENU button until “SOUN” is displayed, and press

ENTER.

2. Tap the UP or DOWN buttons to choose either OFF or ON, and

press ENTER, then press and hold MENU for 3 seconds to con-

rm. To adjust sound sensitivity see page 11.

3. The optional UC3 Controller (not included) may be used to con-

trol different functions including blackout.

Show Mode: In this mode you can choose 1 of 12 show modes to

run.

1. Tap the MENU button until “SHND” is displayed, and press

ENTER.

2. Tap the UP or DOWN buttons until you nd your desired show,

and press ENTER then press and hold MENU for 3 seconds to

con rm. See page 11 for more info.

3. The optional UC3 Controller (not included) may be used to con-

trol different functions including blackout.

Fun Factor LED UC3 Control

With this feature you can connect the xtures to one another

using the IEC input and output sockets. The quantity that can be

connected is 17 xtures maximum. After 17 xtures you will need

to use a new power outlet. They must be the same xtures. DO

NOT mix xtures.

Fun Factor LED Power Cord Daisy Chain

Blackout Blackout the unit

Function

1. White Strobe(Press and hold on the first time).

2. Sound White Strobe(Press and hold on the

second time).

3. Always Sound Color.

Select Show (Show 1-12).

When exit it will run

Show 0(random show).

ModeSound/Strobe

(LED OFF)

Show

(LED ON)

American DJ®- www.americandj.com - Fun Factor LED Instruction Manual Page 17 American DJ®- www.americandj.com - Fun Factor LED Instruction Manual Page 18

Fun Factor LED 4 DMX Channel Mode

Channel Value Function

1 MODE

0 - 119 PATTERNS

120 - 239 CHASES

240 - 255 SOUND ACTIVE

2 PATTERNS/CHASES

0 - 15 BLACKOUT

16 - 31 PATTERN/CHASE 1

32 - 47 PATTERN/CHASE 2

48 - 63 PATTERN/CHASE 3

64 - 79 PATTERN/CHASE 4

80 - 95 PATTERN/CHASE 5

96 - 111 PATTERN/CHASE 6

112 - 127 PATTERN/CHASE 7

128 - 143 PATTERN/CHASE 8

144 - 159 PATTERN/CHASE 9

160 - 175 PATTERN/CHASE 10

176 - 191 PATTERN/CHASE 11

192 - 207 PATTERN/CHASE 12

208 - 223 PATTERN/CHASE 13

224 - 239 PATTERN/CHASE 14

240 - 255 PATTERN/CHASE 15

3 PATTERN STROBING/CHASE SPEED

0 - 9 BLACKOUT (PATTERN)

10 - 255 STROBING SLOW - FAST (PATTERN)

10 - 255 CHASE SPEED SLOW - FAST

4 WHITE LED

0 - 7 OFF

8 - 15 FULL ON

16 - 127 STROBING SLOW - FAST

128 - 143 CHASE 1 SLOW - FAST

144 - 159 CHASE 2 SLOW - FAST

160 - 175 CHASE 3 SLOW - FAST

176 - 191 CHASE 4 SLOW - FAST

192 - 207 CHASE 5 SLOW - FAST

Fun Factor LED 4 DMX Channel Mode

Channel Value Function

4 WHITE LED

208 - 223 CHASE 6 SLOW - FAST

224 - 239 CHASE 7 SLOW - FAST

240 - 255 CHASES 1-7 SLOW - FAST

American DJ® - www.americandj.com - Fun Factor LED Instruction Manual Page 19 American DJ®- www.americandj.com - Fun Factor LED Instruction Manual Page 20

Fun Factor LED 8 Channel Mode - DMX Traits

Channel Value Function

1 MODE

0 - 119 PATTERNS

120 - 239 CHASES

240 - 255 SOUND ACTIVE

2 PATTERNS/CHASES (LENS 1)

0 - 15 BLACKOUT

16 - 31 PATTERN/CHASE 1

32 - 47 PATTERN/CHASE 2

48 - 63 PATTERN/CHASE 3

64 - 79 PATTERN/CHASE 4

80 - 95 PATTERN/CHASE 5

96 - 111 PATTERN/CHASE 6

112 - 127 PATTERN/CHASE 7

128 - 143 PATTERN/CHASE 8

144 - 159 PATTERN/CHASE 9

160 - 175 PATTERN/CHASE 10

176 - 191 PATTERN/CHASE 11

192 - 207 PATTERN/CHASE 12

208 - 223 PATTERN/CHASE 13

224 - 239 PATTERN/CHASE 14

240 - 255 PATTERN/CHASE 15

3 PATTERNS/CHASES (LENS 2)

(SEE CHANNEL 2)

4 PATTERNS/CHASES (LENS 3)

(SEE CHANNEL 2)

5 PATTERNS/CHASES (LENS 4)

(SEE CHANNEL 2)

6 PATTERNS/CHASES (LENS 5)

(SEE CHANNEL 2)

7 PATTERN STROBING/CHASE SPEED

0 - 9 BLACKOUT (PATTERN)

10 - 255 STROBING SLOW - FAST (PATTERN)

10 - 255 CHASE SPEED SLOW - FAST

Fun Factor LED 8 Channel Mode - DMX Traits

Channel Value Function

8 WHITE LED

0 - 7 OFF

8 - 15 FULL ON

16 - 127 STROBING SLOW - FAST

128 - 143 CHASE 1 SLOW - FAST

144 - 159 CHASE 2 SLOW - FAST

160 - 175 CHASE 3 SLOW - FAST

176 - 191 CHASE 4 SLOW - FAST

192 - 207 CHASE 5 SLOW - FAST

208 - 223 CHASE 6 SLOW - FAST

224 - 239 CHASE 7 SLOW - FAST

240 - 255 CHASES 1-7 SLOW - FAST

Inhaltsverzeichnis

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ BU-200 Bedienungsanleitung

American DJ

American DJ X-Scan LED Plus Bedienungsanleitung

American DJ

American DJ Charisma II Bedienungsanleitung

American DJ

American DJ LED Beam Scan Bedienungsanleitung

American DJ

American DJ M-103HD Bedienungsanleitung

American DJ

American DJ GP 250 Bedienungsanleitung

American DJ

American DJ Flight-Moon Bedienungsanleitung

American DJ

American DJ 1.4 Bedienungsanleitung

American DJ

American DJ LED Vision Bedienungsanleitung

American DJ

American DJ DJ Spot 250 Bedienungsanleitung

American DJ

American DJ UV Panel HP Bedienungsanleitung

American DJ

American DJ Jelly Jewel LED Bedienungsanleitung

American DJ

American DJ Pinspot LED RC Bedienungsanleitung

American DJ

American DJ UVLED Bar16 Bedienungsanleitung

American DJ

American DJ Centurion Bedienungsanleitung

American DJ

American DJ Sunray-150D Bedienungsanleitung

American DJ

American DJ FLASHBACK 4 Bedienungsanleitung

American DJ

American DJ Inno Color Beam Z7 Bedienungsanleitung

American DJ

American DJ Snow Flurry Montageanleitung

American DJ

American DJ Fusion FX Bar 4 Bedienungsanleitung

American DJ

American DJ RGBW Bedienungsanleitung

American DJ

American DJ Emerald Scan Bedienungsanleitung

American DJ

American DJ Roto-Balls VS MKII Bedienungsanleitung

American DJ

American DJ Flash-1C Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung