American DJ Prismatic Bedienungsanleitung

User Instructions

©American DJ® - www.americandj.com - Prismatic Instruction Manual Page 2

Unpacking: Thank you for purchasing the Prismatic by American DJ®.

Every Prismatic has been thoroughly tested and has been shipped in

perfect operating condition. Carefully check the shipping carton for

damage that may have occurred during shipping. If the carton appears

to be damaged, carefully inspect your unit for any damage and be sure

all equipment necessary to operate the unit has arrived intact. In the

event damage has been found or parts are missing, please contact

our toll free customer support number for further instructions. Please

do not return the unit to your dealer without ﬁrst contacting customer

support.

Introduction: Thank you for purchasing the American DJ® Prismatic.

™

The Prismatic is a small, lightweight ﬁxture that produces a very color-

ful effect. The unit has 2-way mode switch that allows the unit to be

operated in two different modes (see page 5 for operating modes). To

optimize beam intensity use this ﬁxture with a fog machine or other

type of special effect smoke.

Customer Support: American DJ® provides a toll free customer sup-

port line, to provide set up help and to answer any question should

you encounter problems during your set up or initial operation. You

may also visit us on the web at www.americandj.com for any com-

ments or suggestions. For service related issue please contact Ameri-

can DJ®. Service Hours are Monday through Friday 9:00 a.m. to 5:00

p.m. Paciﬁc Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2610

E-mail: [email protected]

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or ﬁre, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

American DJ.

PLEASE recycle the shipping carton whenever possible.

Prismatic General Introduction

American DJ®

4295 Charter Street

Los Angeles, CA. 90058

www.americandj.com

8/06

PRISMATIC

American DJ®

©American DJ® - www.americandj.com - Prismatic Instruction Manual Page 4©American DJ® - www.americandj.com - Prismatic Instruction Manual Page 3

Please carefully read and understand the instructions in this manual

thoroughly before attempting to operate this unit. These instructions

contain important safety information regarding the use and mainte-

nance of this unit. Please keep this manual with the unit, for future

reference.

Prismatic General Instructions Prismatic Precautions

Prismatic Warranty Registration

The Prismatic carries a one year (365 days) limited warranty. Please

fill out the enclosed warranty card to validate your purchase. All

returned service items whether under warranty or not, must be freight

pre-paid and accompany a return authorization (R.A.) number. If the

unit is under warranty you must provide a copy of your proof of pur-

chase invoice. Please contact American DJ® customer support for a

R.A. number.

Safety Issues: This unit may blow the fuse if the maximum allotted load

of 5 amps is reached. If the fuse needs replacement, always replace the

fuse with same exact type that was remove, unless otherwise instructed

by an authorized American DJ® service technician. Use of a different type

fuse from that which is recommended may cause fire or electric shock

and will void the manufactures warranty.

• To reduce the risk of electrical shock or ﬁre, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit

• Do not attempt to operate this unit if the power cord has been frayed

or broken

• Do not attempt to remove or break off the ground prong from the

electrical cord. This prong is used to reduce the risk of electrical

shock and ﬁre in case of an internal short

• Disconnect from main power before making any type of connection

• Do not remove the cover under any conditions. There are no user

serviceable parts inside

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall

• Do not attempt to operate this unit, if it becomes damaged

• This unit is intended for indoor use only, use of this product outdoors

voids all warranties

• During long periods of non-use, disconnect the unit’s main power

• Always mount this unit in safe and stable matter

• Power cords should be routed so they are not likely to be walked on,

pinched by items placed upon or against them.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 9 for cleaning details

• Heat -The appliance should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including

amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the unit.

C. The unit has been exposed to rain or water.

D. The unit does not appear to operate normally or exhibits a

marked change in performance.

Prismatic Cleaning

Fixture Cleaning:

Due to fog residue, smoke, and dust cleaning the internal and exter-

nal lenses should be carried out periodically to optimize light output.

1. Use normal glass cleaner and a soft cloth to wipe down the

outside casing.

2. Clean the external optics with glass cleaner and a soft cloth every

20 days.

4. Clean the internal optics with glass cleaner and a soft cloth every

30-60 days.

5. Always be sure to dry all parts completely before plugging the unit

back in.

Cleaning frequency depends on the environment in which the fixture

operates (I.e. smoke, fog residue, dust, dew). In heavy use we rec-

ommend cleaning on a monthly basis. Periodic cleaning will ensure

longevity, and crisp beam output.

©American DJ® - www.americandj.com - Prismatic Instruction Manual Page 5 ©American DJ® - www.americandj.com - Prismatic Instruction Manual Page 6

Prismatic Fuse & Lamp Replacement Prismatic Operation

Power Supply: Before plugging your unit in, be sure the source

voltage in your area matches the required voltage for your American

DJ® Prismatic before attempting operation.

General Operation: Just plug this light in, and watch it go. This fix-

ture is designed to operate as a stand alone unit. It has been tested

and the lamp has been installed at the factory there is no assembly

necessary. The Prismatic is ready to be plugged in, out of the box.

There is no power switch, after plugging in the unit the lamp should

turn on, and the internal prism will be sound active. If there is no lamp

output check the fuse and bulb. If the fuse and bulb are good, please

return the unit for servicing.

Operating Modes:

This unit comes with a 2-way operating switch located on the bottom

of the unit. The switch controls two (2) different operating modes.

Switch in the up position: Mode 1 - In this mode the gobo/color

wheel will spin continuously in one direction, while the internal prism

will react to sound.

Switch in the down position: Mode 2 - In this mode the gobo/color

wheel will remain static, while the internal prism will react to sound.

Focusing:

The unit has a fully focusing lens. The lens is focused by manually

turning the lens in either a clockwise or counter-clockwise direction.

Caution: Always replace with the exact same type lamp, unless oth-

erwise specified by an authorized American DJ® technician. Replace

with anything other than the specified part can damage your unit and

will void your manufactures warranty.

Warning: If after you have replaced the lamp or fuse and you con-

tinue to blow either one, STOP using the unit. Contact customer sup-

port for further instructions, you may have to return the unit for ser-

vicing. Continuing to use the unit may cause serious damage.

Fuse Replacement: First unplug the power. Locate the unit’s power

cord. The fuse holder is located above the power cord. Using a flat-

head screw driver unscrew the fuse holder. Remove the bad fuse and

replace with a new one.

Lamp Replacement: Caution! Never open the unit when in use.

Always disconnect the main power and allow the fixture ample time

to cool before attempting to replace the lamp. Again, please remem-

ber to always replace with the exact same type lamp.

1. Be sure to follow the proper procedures when handling halogen

lamps. Never touch the new lamp with your bare fingers.

2. Unscrew the single thumb screw located at the back of the unit.

3. Once the thumb screw has been removed, remove the lamp

cover plate to expose the lamp.

4. Remove and replace the lamp with an exact match.

5. Reassemble in reverse order.

Halogen Lamp Warning! This fixture is fitted with

halogen lamps which are highly susceptible to

damage if improperly handled. Never touch the

lamps with your bare fingers as the oil from your

hands will shorten lamp life. Also, never move the

fixture until the lamps have had ample time to cool.

Remember, lamps are not covered under warranty

conditions.

©American DJ® - www.americandj.com - Prismatic Instruction Manual Page 7

1 YEAR LIMITED WARRANTY

A. American DJ® hereby warrants, to the original purchaser, American DJ® products to be

free of manufacturing defects in material and workmanship for a period of one Year (365

days) from the date of purchase. This warranty shall be valid only if the product is pur-

chased within the United States of America, including possessions and territories. It is the

owner’s responsibility to establish the date and place of purchase by acceptable evidence,

at the time service is sought.

B. For warranty service, send the product only to the American DJ® factory. All shipping

charges must be pre-paid. If the requested repairs or service (including parts replacement)

are within the terms of this warranty, American DJ® will pay return shipping charges only

to a designated point within the United States. If the entire instrument is sent, it must be

shipped in its original package. No accessories should be shipped with the product. If any

accessories are shipped with the product, American DJ® shall have no liability whatsoever

for loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is

modiﬁed in any manner which American DJ® concludes, after inspection, affects the reli-

ability of the product; if the product has been repaired or serviced by anyone other than

the American DJ® factory unless prior written authorization was issued to purchaser by

American DJ®; if the product is damaged because not properly maintained as set forth in

the instruction manual.

D. This is not a service contract, and this warranty does not include maintenance, cleaning

or periodic check-up. During the period speciﬁed above, American DJ® will replace defec-

tive parts at its expense, and will absorb all expenses for warranty service and repair labor

by reason of defects in material or workmanship. The sole responsibility of American DJ®

under this warranty shall be limited to the repair of the product, or replacement thereof,

including parts, at the sole discretion of American DJ®. All products covered by this war-

ranty were manufactured after January 1, 1990, and bear identifying marks to that effect.

E. American DJ® reserves the right to make changes in design and/or improvements upon

its products without any obligation to include these changes in any products theretofore

manufactured.

F. No warranty, whether expressed or implied, is given or made with respect to any acces-

sory supplied with products described above. Except to the extent prohibited by applicable

law, all implied warranties made by American DJ® in connection with this product, includ-

ing warranties of merchantability or ﬁtness, are limited in duration to the warranty period

set forth above. And no warranties, whether expressed or implied, including warranties of

merchantability or ﬁtness, shall apply to this product after said period has expired. The

consumer’s and or Dealer’s sole remedy shall be such repair or replacement as is expressly

provided above; and under no circumstances shall American DJ® be liable for any loss or

damage, direct or consequential, arising out of the use of, or inability to use, this product.

G. This warranty is the only written warranty applicable to American DJ® Products and

supersedes all prior warranties and written descriptions of warranty terms and conditions

heretofore published.

H. Lamps are not covered under this or any other warranty either written or implied.

Prismatic Warranty

©American DJ®

American DJ World Headquarters:

4295 Charter Street Los Angeles, CA 90058 USA

Tel: 323-582-2650 / Fax: 323-582-2610

Web: www.americandj.com / E-mail: [email protected]

Technical Specifications:

Model: Prismatic

Voltage: 120v~60Hz or 230v~50Hz

Lamp: LL-EFP 12v/100w

Fuse: 5 Amp (120v)/ 3.15 Amp (230v)

Dimensions: 10.71”(L) x 7.16”(W) x 9.49”(H)

Colors: Multi-Colored Mirror

Gobos: 1 Interchangeable (26mm -

20mm viewable)

Weight: 3.97 Lbs. / 1.8 Kgs.

Duty Cycle: None

Ventilation: Fan Cooled

Warranty: 1 Year (365 Days)

Please Note: Speciﬁcations and improvements in the design

of this unit and this manual are subject to change without any

prior written notice.

Prismatic Specifications

Inhaltsverzeichnis

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ Flat Par Tri18X Bedienungsanleitung

American DJ

American DJ Spherion Tri LED Bedienungsanleitung

American DJ

American DJ SWEEPER BEAM LED Bedienungsanleitung

American DJ

American DJ Spherion WH LED Bedienungsanleitung

American DJ

American DJ Duo Scan RG Bedienungsanleitung

American DJ

American DJ T4 Bedienungsanleitung

American DJ

American DJ Aggressor Tri LED Bedienungsanleitung

American DJ

American DJ Color 150/RG Bedienungsanleitung

American DJ

American DJ Fusion FX Bar 4 Bedienungsanleitung

American DJ

American DJ Punch LED PRO Bedienungsanleitung

American DJ

American DJ LunarPod Bedienungsanleitung

American DJ

American DJ P64 LED UV Bedienungsanleitung

American DJ

American DJ Fusion Tri FX Bar Bedienungsanleitung

American DJ

American DJ FS-DMXT Bedienungsanleitung

American DJ

American DJ Theatrix PRO 48 LED Bedienungsanleitung

American DJ

American DJ Colorwash 4 Bedienungsanleitung

American DJ

American DJ H2O 250 Montageanleitung

American DJ

American DJ LED Touch Bedienungsanleitung

American DJ

American DJ Trance Wheel 250 Bedienungsanleitung

American DJ

American DJ User Instructions Bedienungsanleitung

American DJ

American DJ Snow Flurry Bedienungsanleitung

American DJ

American DJ Ruby Royal Bedienungsanleitung

American DJ

American DJ Roto-Balls VS MKII Bedienungsanleitung

American DJ

American DJ Micro Image RGB Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung