American Dynamics Illustra 400 Bedienungsanleitung

1 Quick Setup Guide

Quick Setup Guide

illustra 400 Fixed IP Indoor Mini-Dome (PoE)

Part Number 8200-2745-03 A0

2 Quick Setup Guide

Quick Setup Guide

WARNING

At close range, infrared light can seriously damage a person's vision. Install this

illuminator with a minimum safety zone of 1.22m ( 4 ft. ) between the illuminator and

the closest possible human contact.

Note: 1.22m ( 4 ft. ) is the actual measurement of the strength of the IR Illuminators

that are being used.

SERVICE WARNING

DO NOT LOOK DIRECTLY INTO AN OPERATONAL IR ILLUMINATOR.

Since the IR light is invisible to the human eye, the only method of verifying a

malfunctioning IR illuminator is to observe the picture at the video output location.

SAFETY PRECAUTIONS

All the following safety and operational instructions to prevent harm or injury to the

operator(s) or other persons should be read carefully before the unit is activated.

Under copyright laws, the contents of this manual may not be copied, photocopied, reproduced,

translated or reduced to any electronic medium or machine-readable form, in whole or in part, without

Rights Reserved,

American Dynamics

6600 Congress Avenue

Boca Raton, FL 33487, U.S.A.

WARNING

To prevent fire or shock hazard, avoid exposing this unit to rain or moisture.

Do not block ventilation openings.

Do not place anything on top of the unit that might spill or fall into it.

Do not attempt to service this unit yourself, as opening or removing covers

may expose you to dangerous voltage or other hazards. Please refer all

servicing to your distributor / retailer.

Do not use liquid cleaners or aerosols for cleaning.

To prevent fire or electric shock, avoid overloading wall outlets or extension

cords.

The installation should be made by a qualified service person.

PoE warning: If the PoE injector is used instead of the supplied power

adaptor, all of the wiring to and from the injector must be routed/ installed

inside a building/ plant and never routed/ installed outside of the building/

plant.

Please only select a power adapter or power certified by UL and marked at

24Vac / 60 Hz, minimum 1A, class 2 or LPS.

Indoor use only.

Please do not look directly at the shining, reflecting surface of the camera

housing. Looking directly could result in eye uncomfortable.

This product should not be used for the same purposes as consumer

electronic devices.

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BYAN INCORRECT

TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE

INSTRUCTIONS.

4 Quick Setup Guide

1. Part Names

1 2 3 4 5 6 7

1. Plug Inlet: A DC 12V inlet that connects to an external power supply.

2. Plug Inlet: An AC 24V inlet that connects to an external power supply.

3. ETHERNET 10/100 Connector: This is a standard RJ-45 connector for 10/100 Mbps Ethernet networks.

PoE (Power over Ethernet) function: Provides power to the device via the same cable as used for the

network connection.

4. AUDIO IN: The connector is used to connect the audio output from other devices to the camera.

5. VIDEO OUT Connector: The connector provides the unit’s composite video signals to a monitor. (This

connector adjusts and improves the images.)

6. AUDIO OUT: Provides the camera’s audio signal to a speaker or stereo.

7. GPIO: This is a 6-PIN connector including the Digital output/input, DC output and GROUND items for

connecting with external devices.

8. USB port: The user can use a USB device cable to connect the IP camera to the USB port on the PC.

9. SD/ SDHC CARD slot: This is used for updating system software and archiving / accessing critical

images.

10. RESET: Recover to factory default.

Quick Setup Guide

2. The Reset Button

You can use the Reset button to return to default, or factory, settings. Press the Reset Button for about 10

seconds. Blue screens will be displayed, and a text saying “RESETTING…” will appear. The device auto

reboots. All settings are back to default. The following items return back to default.

[SETUP]

Network Setup

a. LAN Settings

b. PPPOE Settings

Dynamic DNS

a. DYNAMIC DNS SETTING

IMAGE SETUP

a. Privacy Mask Setting

b. IMAGE SETTINGS

AUDIO AND VIDEO

a. VIDEO PROFILE 1

b. VIDEO PROFILE 2

c. VIDEO PROFILE 3

d. AUDIO SETTINGS

MOTION DECTION

a. Video Motion setting

TIME AND DATE

a. TIME CONFIGURATION

b. AUTOMATIC TIME CONFIGURATION

c. SET DATE AND TIME MANUALLY

Event Setup

a. Server

b. Media

c. Event

d. Recording

[ADVANCED]

DI and DO

a. DI and DO

b. LED

c. VIDEO OUTPUT

ICR

a. ICR

HTTPS

a. HTTPS

Access List

a. Allow List

b. Deny List

Reset button

6 Quick Setup Guide

3. Install, configure and set the IP Dome Camera

The IP Indoor Mini-dome software default setting is DHCP OFF. Users can build the IP Indoor Mini-dome

working environment with a static IP address. The default static IP is 192.168.1.168. You can set an IP

address for the IP Indoor Mini-dome if the LAN unit isn’t connected to a DHCP server. Or turn on the DHCP

setting to use the DHCP protocol if the DHCP server is working in the LAN. The IP Indoor Mini-dome will

obtain an IP address automatically from the DHCP server. The IP Indoor Mini-dome is linked by its Video Out

connection via a BNC connector to a monitor's Video In connection. If this connection is enabled, you will see

information on the monitor screen, such as, the IP Indoor Mini-dome factory default Static IP address.

1. Check the IP class of your PC

Step 1: Select Settings from the Start menu, and then click Control Panel.

Step 2: Double-click the Network Connections icon. The Network Connections dialog box appears.

Step 3: Click the Protocols tab in the Network Connections dialog box.

Step 4: Select Internet Protocol (TCP/IP) and click Properties.

Step 5: Select Use the following IP Address to indicate that you do not wish to use the DHCP, and assign

IPAddress 192.168.1.200 with Subnet mask 255.255.255.0. Click OK when you finish.

Step 6: Choose Close to finish the modification.

2. Install UPnP Packets of your PC

Microsoft Windows XP®does not start the UPnP service by default. Some packets must be installed before it

is initialized, as described below.

Step 1: Select Set Program Access and Default from the Start menu.

Step 2: Click the Add/Remove Windows Components button when the Add or Remove Programs dialog

box appears.

Step 3: Check the Network Services in the Windows Component Wizard dialog box, and then click

Details….

Step 4: Check UPnP User Interface, and choose OK.

Step 5: Click Next when the original Network Component Wizard dialog box returns. After about one

minute the UPnP installation is complete.

Step 6: Select Finish to close.

3. Turn on Services of your PC

After installation, turn on the relative services to start the UPnP protocol. The following procedures will

demonstrate this.

Step 1: Select Settings from the Start menu, and then click Control Panel.

Step 2: Double-click the Administrative Tools icon. The Administrative Tools dialog box appears.

Step 3: Click the Services icon in the Administrative Tools dialog box.

Step 4: Double-click the SSDP Discovery Service icon when the Services dialog box shows up.

Step 5: Choose Automatic in the Startup type, and click OK to start it. The Services dialog box appears

again.

Step 6: Double-click the Universal Plug and Play Device Host icon.

Step 7: Choose Automatic in the Startup type, press the Start button, and click OK to start it.

Step 8: Restart your system.

4. Set the static IP address in the IP Dome Camera.

Step 1: Plug in the IP Dome Camera power connection.

Step 2: Plug the USB connector into your PC’s USB socket and the other end of the connector in the rear of

the dome lens. A window pops up asking if you want to "Run the program", "Open folder to view files",

or "Take no action".

Step 3: Choose "Run the program" and click "OK", and the "USB configuration" window will pop up.

Step 4: Set the Network setting and type in the IP address you desire. Before you change the IP address, you

should note the factory default Static IP address ( 192.168.1.168 ).

Step 5: Click the "Apply" button in the "USB Configuration” window. A message pops up asking you to

confirm the action as "OK".

Step 6: Click "OK", and remove the USB connection from your PC.

Quick Setup Guide

Step 7: Click "Exit" at the bottom of the "USB Configuration” window to close the window. Alternatively you

can click the "Launch" button to see the local camera images immediately. However, you must check

your PC’s IP address and link to your camera with the network connector (RJ-45) before doing so.

Step 8: If you can see the images, then the IP setting is complete.

5. Scan IP Dome Camera through “My Network Place”

After your installation and starting services, the UPnP protocol will take effect.

Step 1: Scan all IP Dome Cameras in My Network Place.

Step 2: Double click the IP DOME CAMERA icon, and the video live stream will pop up automatically without

assigning any IP address in the Microsoft Internet Explorer.

6. Change the IP Dome Camera's control and operational settings.

Step 1: Enter the IP address in the IE Browser. You will now see the IP Dome Camera images.

Step 2: Use the buttons below the images to enter any other operational settings pages.

Step 3: When you change any setting, please remember to click the "Submit” button in each page.

NOTE: Enable DHCP Function: This function can only work if the LAN, which the unit is connected to,

has a DHCP server. If the DHCP server is working, the IP Dome Camera will obtain an IP address

automatically from the DHCP server.

NOTE: The default "User Name" and "Password" are admin and 9999, respectively. If either the user

name or the password is incorrect, please check the input data and rectify it as necessary.

NOTE: When only one unit of the IP Dome Camera is connected to a computer or LAN, you can freely

assign an IP address for the IP Dome Camera. For example, there is a range of IP Dome Camera

IP addresses from 192.168.1.1 to 192.168.1.255. You can pick one for use from the range of the

IP. It is not necessary to set MASK and GATEWAY; leave the settings as default.

When an IP Dome Camera is connected to a WAN, you must acquire a unique, permanent IP

address and correctly configure the MASK and GATEWAY settings according to your network

architecture. If you have any questions regarding those settings, please consult a qualified MIS

professional or your ISP.

8 Quick Setup Guide

Specifications Illustra 400 Fixed IP Indoor Mini-Dome (PoE)

Model

ADCi400-D011