AMG AMG4784R Bedienungsanleitung

AMG System

s Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page

AMG4783

Instruction

Sheet

D16742

02.doc

AMG4783 Instruction

Manual

8 Channel Video Transmit Unit with 1 Bi

directional Data

Channel for a Singlemode Fibre Link

The

AMG4783

is a standalone eight channel video transmit unit designed to transmit 8 video signals

and transmit and receive 1

data signal over two Singlemode fibres.

The

AMG4783

is designed to be powered using an

AMG2003

standalone power supply.

The

AMG4783

is designed to operate with

AMG4784

or rackmount equivalent

AMG4784R

eight

channel video receive unit in a point to poi

nt configuration.

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use

Page

AMG4783

Instruction

Sheet

D16742

02.doc

Contents

Introduction

Unit Functional Schematic

................................

..................

Optical Connection

................................

.............................

Connections

Video Input

Connections

................................

....................

Optical Connections

................................

...........................

Power Connection

................................

..............................

Data and Audio Channel Connections

................................

...............................

Data and Audio Channel Configuration

................................

..............................

Data Interface Connections Channel A

................................

..............................

Data Channel A Configuration

................................

............

Front Panel Indicators

Power LED

................................

..........

Video Input LED’s

................................

...............................

Fibre Optic LED’s

................................

...............................

Low Speed Data LEDs

................................

.......................

Physical Information

Dimensions

................................

.........

Mounting Details

................................

Removal / replacement from / to the Case

................................

.........................

Safety

Maintenance and Repair

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information her

ein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page

AMG4783

Instruction

Sheet

D16742

02.doc

Introduction

Unit Functional Schematic

The

AMG4783

transmits up to 8 video and

1 data signal to the

AMG4784

It also receives 1 data channel transmitted

from the

AMG4784

Optical Connection

The

AMG4783

is connected as illustrate

d below when used with an

AMG4784R

channel receive

unit acting as a point to point system.

AMG Systems Ltd. reserves

the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page

AMG4783

Instruction

Sheet

D16742

02.doc

Connections

Video Input Connections

No. of channels

................................

....

Connector

................................

............

75 ohm BNC Socket.

Input Impedance

................................

75 ohm terminated.

Input Level

................................

...........

1 volt p

p nominal

Freque

ncy Response

...........................

10Hz to 7MHz.

Optical Connections

PRIMARY OPTO OUT

Connector

................................

............

LC/PC

Primary Optical Launch Power

............

5dBm

Wavelength

................................

..........

1310nm

Optical Fibre

................................

........

Singlemode

PRIMARY OPTO IN

Connector

................................

............

LC/PC

Primary Optical Sensitivity

...................

22dBm

Wavelength

................................

..........

1310nm

Optical Fi

bre

................................

........

Singlemode

Power Connection

Connector Type

................................

...

2.1mm screw lock long power jack

–

centre positive

Connector Partno.

................................

Switchcraft S761K, AMG G16125

Supply Voltage

................................

.....

13.5 to 18.0 Volts DC.

Maximum Power

................................

10 Watts

Data and Audio Channel Connections

DATA

CHANNEL A

Data Channel A

................................

...

1 channel

Data Connector

................................

....

RJ45

Channel A Interface

On Board Data Interface

–

RS232, RS422 or RS485. Selected by slide switch

above RJ45 connector.

RS485

–

switch position

high (closest to BNC connections)

RS422

–

switch posit

ion

–

middle

RS232

–

switch position

–

low (furthest from BNC connections)

DATA CHANNEL B

Data Channel B

................................

...

Not Present

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page

AMG4783

Instruction

Sheet

D16742

02.doc

Data and Audio Channel Configuration

The

AMG4783

and rackmount equivalent

AMG4783R

sends and rece

ives data to/from Channel A.

Channel B is not available. Channel A is a single data interface selectable by the user with the slide

switch on the rear panel.

Data Interface Connections Channel A

Channel A

RJ45 Pin

No.

RS485

[switch high]

RS422

[switch mid]

RS232

[switch low]

Cat 5/6 Cable

Colour Code T568B

IN + (A)

GND

White/orange

(B)

Orange

White/green

Blue

White/blue

Green

IN/OUT + (A)

OUT + (A)

N/A

White/brown

IN/OUT

(B)

OUT

(B)

OUT

Brown

Note: (A) or (B) in brackets in above table refers to RS485 / RS422 data specification, not Channel A,

Channel B.

Data Channel A Configuration

Channel A is always present and allows for a RS232, RS422 (full duplex, four wire)

or RS485 (half

duplex, two wire) interface depending on the position of the switch located above the RJ45 connector.

The switch signifies the presence of the X16004 Low Speed Data/Audio Interface Board. If there are

LED's present on the RJ45 connector then

an X16003 Ethernet Interface Board is fitted.

The data input for both the RS485 and the RS422 modes detects a tri

state input condition by

monitoring the differential voltage level across the input. A differential level below 600mV positive or

negative w

ill be detected as a tri

state condition. A level above 600mV positive or negative will be

detected as a logic 1 or logic zero respectively. It is important therefore to terminate the RS485 bus or

the RS422 input bus using 120Ωif a pre

bias is present on

the RS485 or RS422 bus.

A large number of third party equipment manufacturers apply a pre

bias on their RS485 bus. This pre

bias is applied by pulling one arm of the RS485 bus high (+5 volts) and the other arm low (0 volts)

using high value resistors wit

hin the third party equipment. In order to ensure that the AMG equipment

detects a tri

state condition, then these resistors should have a value above 5kΩ. If the third party

bias resistors are less the 750Ωthe bus can be double or triple terminated as r

equired to ensure that a

tri

state level is detected.

Note: The Data Channel A is shipped from the factory set up for RS485 operation unless otherwise

requested.

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page

AMG4783

Instruction

Sheet

6742

02.doc

Front Panel Indicators

Power LED

Power

................................

...................

Green

unit powered

Off

no power applied to u

nit

Video Input LED’s

Video Present CH1

...........................

Green

video signal present on input BNC

R/G

channel present but no video on I/P BNC

Fibre Optic LED’s

Primary Opto Sync TX

.........................

Green

optical channel transmitting

Off

optical channel not transmitting

imary Opto Sync RX

.........................

Green

optical channel receiving

Org

optical channel receiving but not sync.

Off

optical channel not transmitting

Low Speed Data LEDs

Channel A

Data Present TX (RS485 or RS422)

...

Green

logic zero (+V,

V) present on IN+, IN

Red

logic one (

V,V+) present on IN+, IN

Off

tri

state off or no connection on IN+, IN

Data Present TX (RS232)

....................

Green

logic zero (+V) present on input IN+

Red

logic transitions present on input IN+

Off

logic one (

V) present on input IN+

This represents the data signals being transmitted on the optical fibre

Data Present RX (RS485 or RS422)

...

Green

logic zero (+V,

V) present on OUT+, OUT

Red

logic one (

V,+V) present on OUT+, OUT

Off

tri

state off or no connection on OUT+, OUT

Data Present RX (RS232)

...................

Green

logic zero (+V) present on OUT+

Red

logic transitions present on OUT+

Off

logic one (

V) present on OUT+

This represents the data signals being received on the optical fibre

AMG Systems Lt

d. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page

AMG4783

Instruction

Sheet

D16742

02.doc

Physical Information

Dimensions

Heigh

................................

..................

112mm

Width

................................

...................

170mm (excluding connectors)

Depth

................................

...................

70mm

Weight

................................

.................

1000grams

Mounting Details

The AMG unit is supplied with a clip

on mounting bracket which should be attached to a panel or wall

using 2 off 4.0mm screws, see diagram on page 1 for dimensions. T

he unit is clipped into the

mounting bracket, and is then held firmly in position.

Removal / replacement from / to the Case

Note:

The AMG unit PCB's are static sensitive. Handle with proper care and use normal electrostatic

discharge (ESD) procedures.

Use properly grounded protection (for example, wrist straps) when

handling the PCB.

To remove units from the case to access the data expansion boards and the daughter boards, remove

the 2 or 4 fixing screws on the rear panel and slide the PCB's out of th

e case.

Ensure that the fibres do not snag or get trapped.

To replace the PCB's into the case, slide the PCB's gently into the case aligning the boards with the

appropriate slots. Ensure that the fibre do not snag or get trapped.

Safety

AMG Optical F

ibre Products use Class 1 laser systems in accordance with EN 60825

2:2000.

It is always advisable to follow good practice when working with optical fibre systems. This includes:



Do not stare with unprotected eyes or with any unapproved collimating devic

e at fibre

ends or connector faces, or point them at other people.



Use only approved filtered or attenuating viewing aids

For other safety issues and advice on good practice associated with optical fibre systems, please see

EN 60825

2:2000 or your local s

afety officer.

Maintenance and Repair

There are no user serviceable parts within AMG products. See unit data sheet for full specification.

In case of problem or failure, please call your local support centre or contact:

AMG Systems Ltd.

3 The Omeg

a Centre, Stratton Business Park, Biggleswade, Beds., SG18 8QB, UK.

Phone

+44 (0) 1767 600 777

Technical Support

+44 (0) 1767 604 491

techsupport@amgsystems.com

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page

AMG4783

Instruction

Sheet

D16742

02.doc

This page is intentionally blank.

Inhaltsverzeichnis

Andere AMG Sender Handbücher

AMG

AMG AMG4683E Bedienungsanleitung

AMG

AMG AMG5803A966G-DF Bedienungsanleitung

AMG

AMG AMG4703E-SF Bedienungsanleitung

AMG

AMG AMG5913-2A9R Bedienungsanleitung

AMG

AMG AMG5611 Bedienungsanleitung

AMG

AMG AMG4707AEG Bedienungsanleitung

AMG

AMG AMG4783RN-CWDMn Bedienungsanleitung

AMG

AMG AMG4783E-DR-SF Bedienungsanleitung

AMG

AMG AMG3743E Bedienungsanleitung

AMG

AMG AMG4787BER-SF Bedienungsanleitung

AMG

AMG AMG4707A-DR-SF Bedienungsanleitung

AMG

AMG AMG4707G Bedienungsanleitung

AMG

AMG AMG4647BR Bedienungsanleitung

AMG

AMG AMG4687B Bedienungsanleitung

AMG

AMG AMG5913-2A9 Bedienungsanleitung

AMG

AMG AMG4713Bx-SF Bedienungsanleitung

AMG

AMG AMG4783B R-SF Series Bedienungsanleitung

AMG

AMG AMG5525 Bedienungsanleitung

AMG

AMG AMG4787R-SF Bedienungsanleitung

AMG

AMG AMG5615 Bedienungsanleitung

AMG

AMG AMG5901 Bedienungsanleitung

AMG

AMG AMG5513A5B9 Bedienungsanleitung

AMG

AMG AMG5713A6B9-DIN Bedienungsanleitung

AMG

AMG AMG3747BE Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung