AMG AMG4781ER Bedienungsanleitung

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 1 of 8

AMG4781ER Instruction Sheet

D32037-00.doc

AMG4781ER Instruction

Manual

8 Video Transmit Unit with Ethernet

The AMG4781ER is a rackmount eight channel video transmit unit designed to transmit 8 video

signals and provide full duplex 100BaseT Ethernet connectivity over two singlemode fibres.

The AMG4781ER is designed to plug into an AMG2009 or AMG2015 subrack, which in turn fits into a

19" rack system.

The AMG4781ER is designed to operate with AMG4782E or rackmount equivalent AMG4782ER eight

channel video receive unit in a point to point configuration.

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 2 of 8

AMG4781ER Instruction Sheet

D32037-00.doc

Contents

Introduction 3

Unit Functional Schematic.................................................................................................................. 3

Optical Connection ............................................................................................................................. 3

Ethernet Operation 3

Connections 4

Video Input Connections .................................................................................................................... 4

Optical Connections ...........................................................................Error! Bookmark not defined.

Power Connection .............................................................................................................................. 4

Ethernet Connection........................................................................................................................... 4

Front Panel Indicators 5

Power LED.......................................................................................................................................... 5

Video Input LED’s ............................................................................................................................... 5

Fibre Optic LED’s ............................................................................................................................... 5

Ethernet Data LED’s ........................................................................................................................... 5

Physical Information 6

Dimensions......................................................................................................................................... 6

Mounting Details................................................................................................................................. 6

Removal / replacement from / to the Case......................................................................................... 6

Safety 6

Maintenance and Repair 6

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 3 of 8

AMG4781ER Instruction Sheet

D32037-00.doc

Introduction

Unit Functional Schematic

The AMG4781ER transmits up to 8 video

signals to the AMG4782E.

Ethernet connectivity is also provided

between the two units.

Optical Connection

The AMG4781ER is connected as illustrated below when used with an AMG4782ER 8-channel

receive unit acting as a point to point system.

Ethernet Operation

In order for the AMG system to transmit Ethernet signals, an onboard RJ45 Ethernet interface or

X16003 Ethernet interface adaptor should be fitted to both the Transmit unit and the Receive unit.

The Ethernet interface can operate at either 10Mbits/s half duplex, or 100Mbit/s full duplex, and data is

transmitted from one port the other port with the minimum of delay or buffering.

The 100BaseT port does not implement MDI/MDIX; it should be connected with a straight though

cable to an external switch port and with a cross over cable when connected directly to a PC or DTE.

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 4 of 8

AMG4781ER Instruction Sheet

D32037-00.doc

Connections

Video Input Connections

No. of channels....................................8

Connector ............................................75 ohm BNC Socket.

Input Impedance..................................75 ohm terminated.

Input Level ...........................................1 volt p-p nominal

Frequency Response...........................10Hz to 7MHz.

Optical Connections

PRIMARY OPTO OUT

Connector ............................................LC/PC

Primary Optical Launch Power............-5dBm

Wavelength..........................................1310nm

Optical Fibre ........................................Singlemode

PRIMARY OPTO IN

Connector ............................................LC/PC

Primary Optical Sensitivity...................-22dBm

Wavelength..........................................1310nm

Optical Fibre ........................................Singlemode

Power Connection

Power supply .......................................from plug in connection on the AMG2009 / AMG2015 subrack

Power consumption.............................10 Watts max.

Ethernet Connection

Ethernet Data Connector ....................RJ45

Interface...............................................Auto-negotiation up to 100BASE-TX full duplex

Ethernet Data Rate..............................Maximum 100Mb/s total Ethernet traffic on fibre

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 5 of 8

AMG4781ER Instruction Sheet

D32037-00.doc

Front Panel Indicators

Power LED

Power ..................................................Green - unit powered

Off - no power applied to unit

Video Input LED’s

Video Present CH1-8 ..........................Green - video signal present on input BNC

R/G - channel present but no video on I/P BNC

Fibre Optic LED’s

Primary Opto Sync TX.........................Green - optical channel transmitting

Off - optical channel not transmitting

Primary Opto Sync RX ........................Green - optical channel receiving

Org - optical channel receiving but not sync.

Off - optical channel not transmitting

Ethernet Data LED’s

BANK A

Data Present TX (Ethernet).................Green - data present on the Ethernet input

Off - no data present on the Ethernet input

This represents the Ethernet signals being transmitted onto the optical fibre

Data Present RX (Ethernet) ................Green - data present on the Ethernet input

Off - no data present on the Ethernet input

This represents the Ethernet signals being received from the optical fibre

BANK B

Data Present TX .................................Green - RJ45 Ethernet port operating at 100Mbit/s

Red - RJ45 Ethernet port operating at 10Mbit/s

Data Present RX..................................Green - RJ45 Ethernet port operating full duplex

Off - RJ45 Ethernet port operating half duplex

Note: the RJ45 Ethernet auto-negotiates up to 100Mbit/s full duplex.

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 6 of 8

AMG4781ER Instruction Sheet

D32037-00.doc

Physical Information

Dimensions

Height...................................................3U Plug-in

Width....................................................14HP

Depth ...................................................170mm excluding connectors

Weight..................................................750grams

Mounting Details

The unit is designed to be mounted within an AMG2009 or AMG2015 Subrack on standard card

guides.

Removal / replacement from / to the Case

Note: - The AMG unit PCB's are static sensitive. Handle with proper care and use normal electrostatic

discharge (ESD) procedures. Use properly grounded protection (for example, wrist straps) when

handling the PCB.

To remove units from the case to access the data expansion boards and the daughter boards, remove

the 2 or 4 fixing screws on the rear panel and slide the PCB's out of the case.

Ensure that the fibres do not snag or get trapped.

To replace the PCB's into the case, slide the PCB's gently into the case aligning the boards with the

appropriate slots. Ensure that the fibre do not snag or get trapped.

Safety

AMG Optical Fibre Products use Class 1 laser systems in accordance with EN 60825-2:2000.

It is always advisable to follow good practice when working with optical fibre systems. This includes:

Do not stare with unprotected eyes or with any unapproved collimating device at fibre

ends or connector faces, or point them at other people.

Use only approved filtered or attenuating viewing aids

For other safety issues and advice on good practice associated with optical fibre systems, please see

EN 60825-2:2000 or your local safety officer.

Maintenance and Repair

There are no user serviceable parts within AMG products. See unit data sheet for full specification.

In case of problem or failure, please call your local support centre or contact: AMG Systems Ltd. at

3 The Omega Centre, Stratton Business Park, Biggleswade, Beds., SG18 8QB, UK.

Phone +44 (0) 1767 600 777

Technical Support +44 (0) 1767 604 491

Email techsupport@amgsystems.com

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 7 of 8

AMG4781ER Instruction Sheet

D32037-00.doc

This page is intentionally blank.

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 8 of 8

AMG4781ER Instruction Sheet

D32037-00.doc

This page is intentionally blank.

Inhaltsverzeichnis

Andere AMG Sender Handbücher

AMG

AMG AMG4681-1550-C Bedienungsanleitung

AMG

AMG AMG4683E Bedienungsanleitung

AMG

AMG AMG4707AG-DR-SF Bedienungsanleitung

AMG

AMG AMG4783R-SF-CWDMn-C Bedienungsanleitung

AMG

AMG AMG5525 Bedienungsanleitung

AMG

AMG AMG4787BER-SF Bedienungsanleitung

AMG

AMG AMG5513 Bedienungsanleitung

AMG

AMG AMG4647-ULTRA1 Bedienungsanleitung

AMG

AMG AMG4783BxE-SF Bedienungsanleitung

AMG

AMG AMG4683B ER Series Bedienungsanleitung

AMG

AMG AMG4687B Bedienungsanleitung

AMG

AMG AMG4783E-DR-SF Bedienungsanleitung

AMG

AMG AMG4784R Bedienungsanleitung

AMG

AMG AMG4684B R Series Bedienungsanleitung

AMG

AMG AMG4707AEG Bedienungsanleitung

AMG

AMG AMG5713A6B9-DIN Bedienungsanleitung

AMG

AMG AMG4681R-CWDMn Bedienungsanleitung

AMG

AMG AMG3741G-DR-SF Bedienungsanleitung

AMG

AMG AMG4783B R-SF Series Bedienungsanleitung

AMG

AMG AMG5513A5B9 Bedienungsanleitung

AMG

AMG AMG4687BER Bedienungsanleitung

AMG

AMG AMG2683 Bedienungsanleitung

AMG

AMG AMG4683ER Bedienungsanleitung

AMG

AMG AMG5611R Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung