AMG AMG5513 Bedienungsanleitung

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 1 of 8 AMG5513 Instruction Sheet D17297-

00.doc

AMG5513

Instruction Manual

Transmit Unit with one Bi-directional Data Channel and one

Bi-directional Alarm for a Singlemode Fibre Link

The AMG5513 is a compact standalone transmit unit designed to transmit and receive 1 data signal

plus 1 Bi-directional alarm over one Singlemode optical fibre.

The AMG5513 is designed to be powered using an AMG2001 standalone power supply.

The AMG5513 is designed to operate with an AMG5514 / AMG5514R single channel or AMG5524 /

AMG5524R dual channel receive unit in a point to point configuration. The R suffix in the partno.

indicates a rackmount configuration.

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 2 of 8 AMG5513 Instruction Sheet D17297-

00.doc

Contents

Introduction 3

Unit Functional Schematic..............................................................................................................3

Optical Connection.........................................................................................................................3

Connections 4

Optical Connections Singlemode....................................................................................................4

Power Connection..........................................................................................................................4

Data and Alarm Channel Connections............................................................................................4

Front Panel Indicators 5

Power / Opto LED..........................................................................................................................5

Low Speed Data LEDs...................................................................................................................5

Alarm LEDs ...................................................................................................................................5

Data and Alarm Channel Configuration 6

Data Channel Configuration...........................................................................................................6

Data Interface Connections............................................................................................................6

Alarm Channel Configuration 7

Bi-directional Alarm Interface Connections.....................................................................................7

Physical Information 8

Dimensions....................................................................................................................................8

Mounting Details............................................................................................................................8

Safety 8

Maintenance and Repair 8

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 3 of 8 AMG5513 Instruction Sheet D17297-

00.doc

Introduction

Unit Functional Schematic

The

AMG5513

transmits 1 data channel

and 1 uni-directional alarm signal to the

AMG5514 receive unit.

It also receives 1 data channel and 1 Bi-

directional alarm transmitted from the

AMG5514.

Optical Connection

The AMG5513 connections are illustrated in the following example which shows an AMG5513

transmit unit together with an AMG5514 receive unit configured as a single channel point to point

system.

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 4 of 8 AMG5513 Instruction Sheet D17297-

00.doc

Connections

Optical Connections Singlemode

No. of Optical Connections................. 1

Optical Fibre...................................... Singlemode

Connector.......................................... SC/PC

Primary Optical Launch Power........... -10dBm

Transmit Wavelength......................... 1310nm

Primary Optical Sensitivity.................. -30dBm

Receive Wavelength.......................... 1510nm

Minimum Optical Dynamic Range ...... 20dB.

Power Connection

Connector Type................................. Removable 2-pin, 3.81mm, Screw Terminal

Connector Partno............................... Phoenix 1803578

Supply Voltage................................... +12 to +15Vdc

Maximum Power................................ 1.5 Watts

Data and Alarm Channel Connections

No. of Data Channels......................... 1

No. of Alarm Channels....................... 1

Connector.......................................... Removable 8-pin, 3.81mm, Screw Terminal

Connector Partno............................... Phoenix 1803633

Data Interface.................................... RS-232, RS-422 or R-S485. Selected by slide switch above the

BNC connector.

RS-232 –Switch Position - Left

RS-422 –Switch Position - Centre

RS-485 –Switch Position - Right

Alarm Input........................................ Contact Closure pull-up is 330R to +3V3

Alarm Output ..................................... Solid-state Relay, maximum 150mA at 125Vac/dc, Ron < 6.5Ω

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 5 of 8 AMG5513 Instruction Sheet D17297-

00.doc

Front Panel Indicators

Power / Opto LED

Power / Opto......................................Green - Unit powered, Opto sync.

Red - Unit powered, no Opto sync.

Off - No power applied to unit

Low Speed Data LEDs

Data Present IN (RS485 or RS422).... Green - logic zero (+V, -V) present on IN+, IN-

Red - logic one (-V,V+) present on IN+, IN-

Off - tri-state off or no connection on IN+, IN-

Data Present IN (RS232)................... Green - logic zero (+V) present on input IN+

Red - logic transitions present on input IN+

Off - logic one (-V) present on input IN+

IN corresponds to the data signals being transmitted onto the optical fibre.

Data Present OUT (RS485 or RS422) Green - logic zero (+V,-V) present on OUT+, OUT-

Red - logic one (-V,+V) present on OUT+, OUT-

Off - tri-state off or no connection on OUT+, OUT-

Data Present OUT (RS232)................ Green - logic zero (+V) present on OUT+

Red - logic transitions present on OUT+

Off - logic one (-V) present on OUT+

OUT corresponds to the data signals being received from the optical fibre.

Alarm LEDs

ALARM IN..........................................Green - Alarm ON / Contacts closed.

Off - Alarm OFF / Contacts open.

ALARM OUT......................................Green - Alarm ON / Contacts closed.

Off - Alarm OFF / Contacts open.

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 6 of 8 AMG5513 Instruction Sheet D17297-

00.doc

Data and Alarm Channel Configuration

Data Channel Configuration

The low speed data channel provides an RS-232, RS-422 (full duplex, four wire) or RS-485 (half

duplex, two wire) interface defined by the mode switch on the front panel. The data channel as

shipped from the factory is set up for RS-485 operation unless otherwise requested.

The data input for both the RS-485 and the RS-422 modes detects a tri-state input condition by

monitoring the differential voltage level across the input. A differential level below 600mV positive or

negative will be detected as a tri-state condition. A level above 600mV positive or negative will be

detected as a logic 1 or logic zero respectively. It is important therefore to terminate the RS-485 bus or

the RS-422 input bus using 120Ωif a pre-bias is present on the RS-485 or RS-422 bus.

A large number of third party equipment manufacturers apply a pre-bias on their RS-485 bus. This pre-

bias is applied by pulling one arm of the RS-485 bus high (+5 volts) and the other arm low (0 volts)

using high value resistors within the third party equipment. In order to ensure that the AMG equipment

detects a tri-state condition, then these resistors should have a value above 5kΩ. If the third party

bias resistors are less than 750Ωthe bus can be multiple terminated as required to ensure that a tri-

state level is detected.

The system detects a tri-state input condition on the data channel bus when in RS-485 or RS-422

mode.

Data Interface Connections

Connector

Pin No.

Data Channel

RS-485

[switch right] RS-422

[switch mid] RS-232

[switch left]

1IN + (A) IN

2IN - (B)

3GND GND GND

7IN/OUT + (A) OUT + (A)

8IN/OUT - (B) OUT - (B) OUT

Note: (A) or (B) in brackets in the above table refers to RS-485 / RS-422 data specification.

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 7 of 8 AMG5513 Instruction Sheet D17297-

00.doc

Alarm Channel Configuration

The AMG5513 provides 1 Bi-directional alarm output / contact closure input.

The alarm input is typically connected to a contact closure switch. An ALARM IN+ input incorporates a

330R pull-up resistor to the internal +3V3 supply.

The alarm output can receive an on/off signal from an AMG5514 and is typically used to convey

contact closure status. An alarm output uses a solid-state relay, with a maximum load current of

150mA at 125Vac/dc and Ron < 6.5Ω.

Bi-directional Alarm Interface Connections

Connector Pin

No.

Alarm Interface

Alarm IN Alarm OUT

3GND

4ALARM IN +

5ALARM OUT -

6ALARM OUT +

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 8 of 8 AMG5513 Instruction Sheet D17297-

00.doc

Physical Information

Dimensions

Height................................................ 56mm

Width................................................. 55mm (excluding connectors)

Depth................................................. 25mm

Weight............................................... 200grams

Mounting Details

The unit is designed to be mounted using the clip holder supplied, which can be fixed to a wall or

panel using 2 off 4mm screws.

Safety

AMG Optical Fibre Products use Class 1 laser systems in accordance with EN 60825-2:2000.

It is always advisable to follow good practice when working with optical fibre systems. This includes:

§Do not stare with unprotected eyes or with any unapproved collimating device at fibre

ends or connector faces, or point them at other people.

§Use only approved filtered or attenuating viewing aids

For other safety issues and advice on good practice associated with optical fibre systems, please see

EN 60825-2:2000 or your local safety officer.

Maintenance and Repair

There are no user serviceable parts within AMG products. See unit data sheet for full specification.

In case of problem or failure, please call your local support centre or contact: AMG Systems Ltd. at

3 The Omega Centre, Stratton Business Park, Biggleswade, Beds., SG18 8QB, UK.

Phone +44 (0) 1767 600 777

Technical Support +44 (0) 1767 604 491

Email techsupport@amgsystems.com

Inhaltsverzeichnis

Andere AMG Sender Handbücher

AMG

AMG AMG5525 Bedienungsanleitung

AMG

AMG AMG4713Bx-SF Bedienungsanleitung

AMG

AMG AMG4783B R-SF Series Bedienungsanleitung

AMG

AMG AMG4643-DR-SF Bedienungsanleitung

AMG

AMG AMG4683B ER Series Bedienungsanleitung

AMG

AMG AMG4743-SF Bedienungsanleitung

AMG

AMG AMG5903A966B9 Bedienungsanleitung

AMG

AMG AMG5613A9R Bedienungsanleitung

AMG

AMG AMG6781 Bedienungsanleitung

AMG

AMG AMG4687B Bedienungsanleitung

AMG

AMG AMG4707AEG Bedienungsanleitung

AMG

AMG AMG5803A966G-DF Bedienungsanleitung

AMG

AMG AMG4784R Bedienungsanleitung

AMG

AMG AMG2683 Bedienungsanleitung

AMG

AMG AMG5615 Bedienungsanleitung

AMG

AMG AMG4647B Bedienungsanleitung

AMG

AMG AMG5813R Bedienungsanleitung

AMG

AMG AMG4684B R Series Bedienungsanleitung

AMG

AMG AMG4783BxE-SF Bedienungsanleitung

AMG

AMG AMG5513A5B9 Bedienungsanleitung

AMG

AMG AMG5913-2A9R Bedienungsanleitung

AMG

AMG AMG5611 Bedienungsanleitung

AMG

AMG AMG5611R Bedienungsanleitung

AMG

AMG AMG4783RN-CWDMn Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung