AMG AMG5513A5B9 Bedienungsanleitung
AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 1 of 12 AMG5513A5B9 Instruction Sheet
D17369-00.doc
AMG5513A5B9
Instruction Manual
Transmit Unit with one Bi-directional Data Signal, two Bi-
directional Alarms and one Bi-directional Audio Channel
for a Singlemode Fibre Link
The AMG5513A5B9 is a standalone transmit unit designed to transmit & receive 1 data signal, 2 Bi-
directional alarms plus 1 Bi-directional audio channel over one Singlemode optical fibre.
The AMG5513A5B9 is designed to be powered using an AMG2001 standalone power supply.
The AMG5513A5B9 is designed to operate with an AMG5514A5B9 / AMG5514A5B9R receive unit in
a point to point configuration. The R suffix in the partno. indicates a rackmount configuration.
AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 2 of 12 AMG5513A5B9 Instruction Sheet
D17369-00.doc
Contents
Introduction 3
Unit Functional Schematic .................................................................................................................. 3
Optical Connection ............................................................................................................................. 3
Connections 4
Optical Connections Singlemode ....................................................................................................... 4
Power Connection .............................................................................................................................. 4
Data and Alarm Channel Connections ............................................................................................... 4
Audio Connections ............................................................................................................................. 4
Front Panel Indicators 6
Power / Opto LED ............................................................................................................................... 6
Low Speed Data LEDs ....................................................................................................................... 6
Alarm LEDs......................................................................................................................................... 6
Audio LEDs ......................................................................................................................................... 6
Data and Alarm Channel Configuration 7
Data Channel Configuration ............................................................................................................... 7
Data Interface Connections ................................................................................................................ 8
Alarm Channel Configuration ............................................................................................................. 8
Alarm Interface Connections .............................................................................................................. 8
Aux. Alarm Interface Connections ...................................................................................................... 9
Audio Interface Connections .............................................................................................................. 9
Audio Channel Configuration .............................................................................................................. 9
Physical Information 10
Dimensions ....................................................................................................................................... 10
Mounting Details ............................................................................................................................... 10
Safety 10
Maintenance and Repair 10
AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 3 of 12 AMG5513A5B9 Instruction Sheet
D17369-00.doc
Introduction
Unit Functional Schematic
The
AMG5513A5B9
transmits 1 data, 2 Bi-
directional alarms and 1 audio signal to the
AMG5514A5B9 receive unit.
It also receives 1 data, 2 Bi-directional
alarms and 1 audio signal transmitted from
the AMG5514A5B9.
Optical Connection
The AMG5513A5B9 connections are illustrated in the following example which shows an
AMG5513A5B9 transmit unit together with an AMG5514A5B9 standalone receive unit configured as a
single channel point to point system.
AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 4 of 12 AMG5513A5B9 Instruction Sheet
D17369-00.doc
Connections
Optical Connections Singlemode
No. of Optical Connections .................. 1
Optical Fibre ........................................ Singlemode
Connector ............................................ SC/PC
Primary Optical Launch Power ............ -10dBm
Transmit Wavelength ........................... 1310nm
Primary Optical Sensitivity ................... -30dBm
Receive Wavelength ............................ 1510nm
Minimum Optical Dynamic Range ....... 20dB.
Power Connection
Connector Type ................................... Removable 2-pin, 3.81mm, Screw Terminal
Connector Partno. ................................ Phoenix 1803578
Supply Voltage ..................................... +12 to +15 Volts DC
Maximum Power .................................. 5 Watts
Data and Alarm Channel Connections
No. of Integral Data Channels ............. 1 Selectable RS-232 / RS-422 / RS-485
No. of Alarms ....................................... 2
Connectors .......................................... Removable 5-pin, 8-pin, 2.5mm, Spring Terminal
Connector Partnos. .............................. Phoenix 1881354, 1881383
Integral Data Interfaces RS-232, RS-422 or R-S485. Selected by slide switch inside enclosure. *See
appropriate section on how to remove the case for access to the data switches
RS-485 – Switch Position - Top
RS-422 – Switch Position - Middle
RS-232 – Switch Position - Bottom
Alarm Input .......................................... Contact Closure pull-up is 330R to +3V3
Alarm Output ........................................ Solid-state Relay, maximum 150mA at 125Vac/dc, Ron < 6.5Ω
Audio Connections
No. of Audio Channels ......................... 1
Connectors .......................................... Removable 5-pin, 2.5mm, Spring Terminal
Connector Partno. ................................ Phoenix 1881354
Input level ............................................ 0dBm
Input overload level .............................. +6dBm
Input impedance .................................. 10kΩ / 600Ω
Output impedance ............................... 600Ω
Frequency response ........................... 10Hz to 20KHz
AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 5 of 12 AMG5513A5B9 Instruction Sheet
D17369-00.doc
Audio Input impedance is selected by removable jumper JP1 or JP2 on Audio Expansion board inside
enclosure. *See appropriate section on how to remove the case for access to the data/audio switches.
1-2 – High Impedance 10kΩ
2-3 – Balanced 600Ω
AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 6 of 12 AMG5513A5B9 Instruction Sheet
D17369-00.doc
Front Panel Indicators
Power / Opto LED
Power / Opto ........................................ Green - Unit powered, Opto sync.
Red - Unit powered, no Opto sync.
Off - No power applied to unit
Low Speed Data LEDs
Data Present IN (RS485 or RS422) .... Green - logic zero (+V, -V) present on IN+, IN-
Red - logic one (-V,V+) present on IN+, IN-
Off - tri-state off or no connection on IN+, IN-
Data Present IN (RS232) ..................... Green - logic zero (+V) present on input IN+
Red - logic transitions present on input IN+
Off - logic one (-V) present on input IN+
IN corresponds to the data signals being transmitted onto the optical fibre.
Data Present OUT (RS485 or RS422) Green - logic zero (+V,-V) present on OUT+, OUT-
Red - logic one (-V,+V) present on OUT+, OUT-
Off - tri-state off or no connection on OUT+, OUT-
Data Present OUT (RS232) ................. Green - logic zero (+V) present on OUT+
Red - logic transitions present on OUT+
Off - logic one (-V) present on OUT+
OUT corresponds to the data signals being received from the optical fibre.
Alarm LEDs
Channel 1
ALARM IN ............................................ Green - Alarm ON / Contacts closed.
Off - Alarm OFF / Contacts open.
ALARM OUT ........................................ Green - Alarm ON / Contacts closed.
Off - Alarm OFF / Contacts open.
Channel 2
ALARM IN ............................................ Green - Alarm ON / Contacts closed.
Off - Alarm OFF / Contacts open.
ALARM OUT ........................................ Green - Alarm ON / Contacts closed.
Off - Alarm OFF / Contacts open.
Audio LEDs
Audio Present TX ................................. Green - audio present > -40dBm
Red - audio present > 0dBm (overload at +6dBm)
Off - audio not present or < -40dBm
This represents the audio signals being transmitted on the optical fibre
Audio Present RX ................................ Green - audio present > -40dBm
Red - audio present > 0dBm (overload at +6dBm)
Off - audio not present or < -40dBm
This represents the audio signals being received from the optical fibre.
AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 7 of 12 AMG5513A5B9 Instruction Sheet
D17369-00.doc
Data and Alarm Channel Configuration
The AMG5513A5B9 transmit unit sends and receives data to/from an AMG5514A5B9 or rackmount
equivalent AMG5514A5B9R receive unit. The physical data interface RS-485, RS-422 or RS-232 is
selectable by the user with the slide switch mounted on the main PCB inside the enclosure.
Two bi-directional alarms are also provided. Each alarm input is typically connected to a contact
closure switch. An alarm output can receive an on/off signal from an AMG5514A5B9 and is typically
used to convey contact closure status.
Data Channel Configuration
Each low speed data channel provides an RS-232, RS-422 (full duplex, four wire) or RS-485 (half
duplex, two wire) interface defined by the corresponding mode switch inside the enclosure. Every data
channel as shipped from the factory is set up for RS-485 operation unless otherwise requested.
The data input for both the RS-485 and the RS-422 modes detects a tri-state input condition by
monitoring the differential voltage level across the input. A differential level below 600mV positive or
negative will be detected as a tri-state condition. A level above 600mV positive or negative will be
detected as a logic 1 or logic 0 respectively. It is important therefore to terminate the RS-485 bus or
the RS-422 input bus using 120Ω if a pre-bias is present on the RS-485 or RS-422 bus.
A large number of third party equipment manufacturers apply a pre-bias on their RS-485 bus. This pre-
bias is applied by pulling one arm of the RS-485 bus high (+5 volts) and the other arm low (0 volts)
using high value resistors within the third party equipment. In order to ensure that the AMG equipment
detects a tri-state condition, then these resistors should have a value above 5kΩ. If the third party
bias resistors are less the 750Ω the bus can be multiple terminated as required to ensure that a tri-
state level is detected.
The system detects a tri-state input condition on the data channel bus when in RS-485 or RS-422
mode.
AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 8 of 12 AMG5513A5B9 Instruction Sheet
D17369-00.doc
Data Interface Connections
Connector
Pin No.
Data Channel
RS-485
[switch top]
RS-422
[switch middle]
RS-232
[switch bottom]
1
IN + (A) IN
2
IN - (B)
3
GND GND GND
4
5
6
7
IN/OUT + (A) OUT + (A)
8
IN/OUT - (B) OUT - (B) OUT
Note: (A) or (B) in brackets in the above table refers to RS-485 / RS-422 data specification.
Alarm Channel Configuration
The AMG5513A5B9 provides 2 bi-directional contact closure inputs / alarm outputs. Each ALARM IN
input is via an internal 10kΩ series resistor with a 47kΩ pull-up resistor to the internal +3V3 supply.
Each ALARM OUT output can receive an on/off signal from an AMG5514A5B9 and is typically used to
convey contact closure status. Each alarm output is an NPN open collector circuit with a maximum
rated continuous load of 500mA / 24Vdc.
Alarm Interface Connections
Connector
Pin No.
Alarm Interface
Alarm IN
Alarm OUT
1
2
3
GND
4
ALARM IN +
5
ALARM OUT -
6
ALARM OUT +
7
8
AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 9 of 12 AMG5513A5B9 Instruction Sheet
D17369-00.doc
Aux. Alarm Interface Connections
Connector
Pin No.
Alarm Interface
Alarm IN
Alarm OUT
1
ALARM OUT +
2
ALARM OUT -
3
GND
4
ALARM IN +
5
ALARM IN -
(GND)
Audio Interface Connections
Connector Pin
No.
Balanced Input
600Ω
High Z input 10kΩ
1
OUT - OUT -
2
OUT + OUT +
3
GND GND
4
IN + IN
5
IN - GND
Audio Channel Configuration
The AMG5513A5B9 provides one bi-directional audio channel.
The audio channel input can be configured as a single-ended high impedance 10kΩ input with GND
reference or alternativly as a balanced 600Ω input pair. The input impedance is selected using
jumpers on the audio expansion board JP1 (Channel 1) or JP2 (Channel 2), the default setting is
balanced 600Ω.
JP1/JP2 1-2 – High Impedance 10kΩ
JP1/JP2 2-3 – Balanced 600Ω
AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 10 of 12 AMG5513A5B9 Instruction Sheet
D17369-00.doc
Physical Information
Dimensions
Height................................................... 112mm
Width .................................................... 170mm (excluding connectors)
Depth ................................................... 70mm
Weight .................................................. 750grams
Mounting Details
The AMG unit is supplied with a clip-on mounting bracket which should be attached to a panel or wall
using 2 off 4.0mm screws, see diagram on page 1 for dimensions. The unit is clipped into the
mounting bracket, and is then held firmly in position.
Safety
AMG Optical Fibre Products use Class 1 laser systems in accordance with EN 60825-2:2000.
It is always advisable to follow good practice when working with optical fibre systems. This includes:
Do not stare with unprotected eyes or with any unapproved collimating device at fibre
ends or connector faces, or point them at other people.
Use only approved filtered or attenuating viewing aids
For other safety issues and advice on good practice associated with optical fibre systems, please see
EN 60825-2:2000 or your local safety officer.
Maintenance and Repair
There are no user serviceable parts within AMG products. See unit data sheet for full specification.
In case of problem or failure, please call your local support centre or contact: AMG Systems Ltd. at
3 The Omega Centre, Stratton Business Park, Biggleswade, Beds., SG18 8QB, UK.
Phone +44 (0) 1767 600 777
Technical Support +44 (0) 1767 604 491
Email techsupport@amgsystems.com
Inhaltsverzeichnis
Andere AMG Sender Handbücher
AMG
AMG AMG5913-2A9 Bedienungsanleitung
AMG
AMG AMG5913-2A9R Bedienungsanleitung
AMG
AMG AMG4627B Bedienungsanleitung
AMG
AMG AMG4643-DR-SF Bedienungsanleitung
AMG
AMG AMG4723 Bedienungsanleitung
AMG
AMG AMG5611R Bedienungsanleitung
AMG
AMG AMG5713A6B9-HP Bedienungsanleitung
AMG
AMG AMG3727BE Bedienungsanleitung
AMG
AMG AMG4681R-CWDMn Bedienungsanleitung
AMG
AMG AMG4787BER-SF Bedienungsanleitung
AMG
AMG AMG2648 Bedienungsanleitung
AMG
AMG AMG4783BxE-SF Bedienungsanleitung
AMG
AMG AMG4713E Bedienungsanleitung
AMG
AMG AMG4784R Bedienungsanleitung
AMG
AMG AMG5613A9R Bedienungsanleitung
AMG
AMG AMG5903A966B9 Bedienungsanleitung
AMG
AMG AMG4687BR Bedienungsanleitung
AMG
AMG AMG4747AG-SF Bedienungsanleitung
AMG
AMG AMG3743E Bedienungsanleitung
AMG
AMG AMG4713Bx-SF Bedienungsanleitung
Beliebte Sender Handbücher anderer Marken
Dejero
Dejero EnGo 3x Bedienungsanleitung
Rosemount
Rosemount 4600 Bedienungsanleitung
Speaka Professional
Speaka Professional 2342740 Bedienungsanleitung
trubomat
trubomat GAB 1000 Bedienungsanleitung
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Bedienungsanleitung
Rondish
Rondish UT-11 Bedienungsanleitung
