AMS AS5 47D-TO EK ST Series Bedienungsanleitung

Eval Kit Manual

DN[Document ID]

ams Eval Kit Manual

Page 1

[v1-00] 2014-Jul-02

Document Feedback

AS5x47

Standard Board

AS5x47-EK_SB

Downloaded from Arrow.com.

AS5x47 Standard Board

ams Eval Kit Manual

Page 2

[v1-00] 2014-Jul-02

Document Feedback

Table of Contents

1Introduction .......................................................................................................................... 3

1.1 Kit Content ........................................................................................................................... 3

2Getting Started..................................................................................................................... 3

3Ordering & Contact Information ........................................................................................... 6

4Copyrights & Disclaimer....................................................................................................... 7

5Revision Information ............................................................................................................ 8

Downloaded from Arrow.com.Downloaded from Arrow.com.

AS5x47 Standard Board

ams Eval Kit Manual

Page 3

[v1-00] 2014-Jul-02

Document Feedback

1 Introduction

The evaluation kit allows an easy and fast evaluation of the AS5x47 rotary magnetic position sensor

in the lab or together with an existing system. It includes all required material to evaluate all product

features.

This small adapterboard is fully assembled with AS5x47 position sensor and its necessary external

components. All relevant signals are available on a dual-row 2.54mm 8-pin header footprint and can

be easily wired to an existing application.

The USB I&P Box is an easy-to use programming and demonstration tool. It can be used to

configure the device and to program a configuration.

A small magnet holder and a knob with a magnet attached on its shaft is enclosed to show the

functionality of the AS5x47.

The AS5x47 is a Hall-based rotary magnetic position sensor with high resolution for fast and

accurate absolute angle measurement over a full turn of 360 degrees. Based on planar Hall

technology, this device can measure the orthogonal component of the flux density (Bz) of a 2-pole

magnet diametrically magnetized. Thanks to its robust architecture the AS5x47x is immune to

homogenous external magnetic stray field.

The 4-wire standard SPI interface allows an external unit (e.g. microcontroller) to communicate with

the AS5x47 as well as to program it without the need of a special programmer.

The absolute position can be read out through the SPI. An incremental angle measurement is

provided as ABI signal with a maximum resolution of 2000 positions per revolution. Easy control of

BLDC motors can be achieved using the UVW interface with a programmable number of pole pairs

from 3 to 6.

1.1 Kit Content

This kit contains following material listed in Table 1. Additional material can be found on our

webpage.

Table 1:

Kit Content

No.

Item

SAP

Info

USB I&P Box

990600795

Programming and Interface Box

AS5x47_EK_AB

Adapterboard including reference magnet

RMH05-DK-XX-1.0

990600534

Rotary Magnet Holder with Knob

For a detailed description of each item please refer to the specific manual. All manuals are available

online on the ams AG website.

2 Getting Started

The AS5x47 adapter board is ideal for rapid setup for the AS5x47 postion sensor because it

includes all necessary tools to operate and configure the AS5x47.

This first steps describes how to connect and use the USB I&P Box together with the AS5x47 Demo

Software and the adapter board.

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

AS5x47 Standard Board

ams Eval Kit Manual

Page 4

[v1-00] 2014-Jul-02

Document Feedback

1st Install the AS5x47 Demo Software

The Software is located on the USB drive that comes with the USB I&P Box or it can be

downloaded from ams webpage. After Installation run the software.

2nd Assemble the Hardware Setup

Follow the Instructions shown below in Figure 1 to set-up the kit.

Figure 1:

Setup Instructions

Note: It might be necessary to perform a firmware update on the USB I&P Box if a wrong firmware

was detected. In this case, the user will be prompted to allow an automatic firmware upgrade.

3rd Start using the software

Following parts of the software are used to perform a configuration and to read-out the AS5600.

Refer to Figure 2 for reference. Read the software user manual for details.

A. Perform your desired settings

B. Read/Write/Burn/Export or Import your configuration

C. Verify the results

USB

A. Short J1 on the adapterboard to set-up the 3V3 mode

Connect the USB I&P Box with the AS5x47_EK_AB using the

10-way cable

C. Place the RMH05 over the adapterboard

D. Connect the USB I&P Box using the USB cable to Computer.

The USB device is detected in Windows and by the AS5x47

Demo Software. The setup is ready for demonstration.

SPI-MISO

SPI-MOSI

GND

SPI-CLK

SPI-CS(0)

VDD

Index

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

AS5x47 Standard Board

ams Eval Kit Manual

Page 5

[v1-00] 2014-Jul-02

Document Feedback

Figure 2:

General Software Instructions

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

AS5x47 Standard Board

ams Eval Kit Manual

Page 6

[v1-00] 2014-Jul-02

Document Feedback

3 Ordering & Contact Information

Ordering Code

Description

AS5x47-EK_SB

AS5x47 Eval Kit Standard Board

Buy our products or get free samples online at:

www.ams.com/ICdirect

Technical Support is available at:

www.ams.com/Technical-Support

Provide feedback about this document at:

www.ams.com/Document-Feedback

For further information and requests, e-mail us at:

ams_sales@ams.com

For sales offices, distributors and representatives, please visit:

www.ams.com/contact

Headquarters

ams AG

Tobelbaderstrasse 30

8141 Unterpremstaetten

Austria, Europe

Tel: +43 (0) 3136 500 0

Website: www.ams.com

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

AS5x47 Standard Board

ams Eval Kit Manual

Page 7

[v1-00] 2014-Jul-02

Document Feedback

4 Copyrights & Disclaimer

translated, stored, or used without the prior written consent of the copyright owner.

Demo Kits, Evaluation Kits and Reference Designs are provided to recipient on an “as is” basis for

demonstration and evaluation purposes only and are not considered to be finished end-products

intended and fit for general consumer use, commercial applications and applications with special

requirements such as but not limited to medical equipment or automotive applications. Demo Kits,

Evaluation Kits and Reference Designs have not been tested for compliance with electromagnetic

compatibility (EMC) standards and directives, unless otherwise specified. Demo Kits, Evaluation Kits

and Reference Designs shall be used by qualified personnel only.

ams AG reserves the right to change functionality and price of Demo Kits, Evaluation Kits and

Reference Designs at any time and without notice.

Any express or implied warranties, including, but not limited to the implied warranties of

merchantability and fitness for a particular purpose are disclaimed. Any claims and demands and any

direct, indirect, incidental, special, exemplary or consequential damages arising from the inadequacy

of the provided Demo Kits, Evaluation Kits and Reference Designs or incurred losses of any kind (e.g.

loss of use, data or profits or business interruption however caused) as a consequence of their use

are excluded.

ams AG shall not be liable to recipient or any third party for any damages, including but not limited to

personal injury, property damage, loss of profits, loss of use, interruption of business or indirect,

special, incidental or consequential damages, of any kind, in connection with or arising out of the

furnishing, performance or use of the technical data herein. No obligation or liability to recipient or

any third party shall arise or flow out of ams AG rendering of technical or other services.

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

AS5x47 Standard Board

ams Eval Kit Manual

Page 8

[v1-00] 2014-Jul-02

Document Feedback

5 Revision Information

Initial version 1-00

Changes from 0-00 (2014-Jul-2) to current revision 1-00 (2014-Jul-2)

Page

Initial version

Note: Page numbers for the previous version may differ from page numbers in the current revision.

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AMS Hauptplatine Handbücher